All Variables Grouped
From Macros Wiki
| Program_Variables | Description |
| PLUGIN_VERSION_1 | Version number of GibbsCAM that the macro plugin |
| PLUGIN_VERSION_2 | was developed for, expressed as 3 values. eg 9.5.1 |
| PLUGIN_VERSION_3 | version_1 = 9, version_2 = 5, version_3 = 1 |
| GIBBSCAM_VERSION_1 | Version number of GibbsCAM that is |
| GIBBSCAM_VERSION_2 | currently running, expressed as 3 values |
| GIBBSCAM_VERSION_3 | same format as plugin_version |
| CURRENT_WG_NUMBER | The current WorkGroup number |
| CURRENT_CS_NUMBER | The current CS number |
| SCREEN_WIDTH | Total screen width, in screen units |
| SCREEN_HEIGHT | Total screen height |
| GIBBSCAM_WINDOW_X1 | Left corner of GibbsCAM window |
| GIBBSCAM_WINDOW_Y1 | Top corner of GibbsCAM window |
| GIBBSCAM_WINDOW_X2 | Right corner of GibbsCAM window |
| GIBBSCAM_WINDOW_Y2 | Bottom corner of GibbsCAM window |
| EXCEL_IS_OPEN | Set to 1 if Excel is currently opened by a macro |
| EXCEL_IS_VISIBLE | Set to 1 if Excel is visible, 0 if hidden |
| Mill Tool Types | Description |
| MTOOL_TYPE_ROUGH_END_MILL | Rough End Mill |
| MTOOL_TYPE_FINISH_END_MILL | Finish End Mill |
| MTOOL_TYPE_BALL_END_MILL | Ball-nosed End Mill |
| MTOOL_TYPE_SHELL_CUTTER | Shell cutter |
| MTOOL_TYPE_FACE_CUTTER | Face Cutter |
| MTOOL_TYPE_FLY_CUTTER | Fly Cutter |
| MTOOL_TYPE_KEY_CUTTER | Key Cutter |
| MTOOL_TYPE_THREAD_MILL | Thread Mill |
| MTOOL_TYPE_DRILL | Drill |
| MTOOL_TYPE_CENTER_DRILL | Center Drill |
| MTOOL_TYPE_SPOT_DRILL | spot Drill |
| MTOOL_TYPE_BORE | Bore |
| MTOOL_TYPE_BACK_BORE | Back Bore |
| MTOOL_TYPE_TAP | Tap |
| MTOOL_TYPE_RIGID_TAP | Rigid Tap |
| MTOOL_TYPE_SPOT_FACE | Spot Face |
| MTOOL_TYPE_REAMER | Reamer |
| MTOOL_TYPE_COUNTERSINK | Countersink |
| MTOOL_TYPE_ROUNDOVER | Roundover |
| MTOOL_TYPE_THREAD_HALF_PROF | Half Profile Thread |
| MTOOL_TYPE_THREAD_FULL_PROF | Full Profile Thread |
| MTOOL_TYPE_CONVEX_TIP | Convex Tip |
| MTOOL_TYPE_BARREL | Barrel |
| MTOOL_TYPE_TAPERED_BARREL | Tapered Barrel |
| MTOOL_TYPE_DOVETAIL | Dovetail |
| MTOOL_TYPE_TAPERED_BARREL | Tapered Barrel |
| MTOOL_TYPE_TANGENT_MILL | Tangent Mill |
| MTOOL_TYPE_FORM | 2D Form Tool |
| MTOOL_TYPE_2DFORM | 2D Form Tool |
| MTOOL_TYPE_3DFORM | 3D Form Tool |
| Lathe Tool Types | Description |
| LTOOL_TYPE_80_DEG | 80 Degree Insert |
| LTOOL_TYPE_75_DEG | 75 Degree Insert |
| LTOOL_TYPE_55_DEG | 55 Degree Insert |
| LTOOL_TYPE_35_DEG | 35 Degree Insert |
| LTOOL_TYPE_ROUND | Round Insert |
| LTOOL_TYPE_SQUARE | Square Insert |
| LTOOL_TYPE_TRIANGLE | Triangular Insert |
| LTOOL_TYPE_TRIGON | Trigon Insert |
| LTOOL_TYPE_PENTAGON | Pentagon Insert |
| LTOOL_TYPE_55_PARA | 55 Degree Parallelogram |
| LTOOL_TYPE_RECTANGLE | Rectangular Insert |
| LTOOL_TYPE_GROOVE | Grooving Tool |
| LTOOL_TYPE_CUTOFF | Cutoff Tool |
| LTOOL_TYPE_THREAD1 | Threading Insert, Type 1 |
| LTOOL_TYPE_THREAD2 | Threading Insert, Type 2 |
| LTOOL_TYPE_THREADN | Threading Insert, Type 1 |
| LTOOL_TYPE_THREADL | Threading Insert, Type 2 |
| LTOOL_TYPE_VPROFILE | V Profile |
| LTOOL_TYPE_FORM | 2D Form Tool |
| LTOOL_TYPE_2DFORM | 2D Form Tool |
| LTOOL_TYPE_3DFORM | 3D Form Tool |
| TOOL_TYPE_UTIL | Utility Tool |
| Long Versions | Description |
| TOOL_ORIENT_UP_RIGHT | Up and Right |
| TOOL_ORIENT_UP_LEFT | Up and Left |
| TOOL_ORIENT_DOWN_LEFT | Down and Left |
| TOOL_ORIENT_DOWN_RIGHT | Down and Right |
| TOOL_ORIENT_RIGHT_UP | Right and Up |
| TOOL_ORIENT_LEFT_UP | Left and Up |
| TOOL_ORIENT_LEFT_DOWN | Left and Down |
| TOOL_ORIENT_RIGHT_DOWN | Right and Down |
| Short Versions | |
| TOOL_ORIENT_UR | Up and Right |
| TOOL_ORIENT_UL | Up and Left |
| TOOL_ORIENT_DL | Down and Left |
| TOOL_ORIENT_DR | Down and Right |
| TOOL_ORIENT_RU | Right and Up |
| TOOL_ORIENT_LU | Left and Up |
| TOOL_ORIENT_LD | Left and Down |
| TOOL_ORIENT_RD | Right and Down |
| Mill Tool Holder Types | Description |
| MTOOL_HOLDER_TYPE_BORE | Bore |
| MTOOL_HOLDER_TYPE_COLLET | Collet |
| MTOOL_HOLDER_TYPE_TG_COLLET | Collet - TG |
| MTOOL_HOLDER_TYPE_DRILL | Drill |
| MTOOL_HOLDER_TYPE_MILL | Mill |
| MTOOL_HOLDER_TYPE_ROT_CLAMP | Rotary Clamp |
| MTOOL_HOLDER_TYPE_SHELL | Shell |
| MTOOL_HOLDER_TYPE_SHRINK_FIT | Shrink Fit |
| MTOOL_HOLDER_TYPE_TAP | Tap |
| Feature_Types | Description |
| FEAT_TYPE_POINT | Point |
| FEAT_TYPE_LINE | Line |
| FEAT_TYPE_ARC | Circular Arc |
| FEAT_TYPE_CURVE | Curve (Spline) |
| FEAT_TYPE_SPLINE | Curve (Spline) |
| FEAT_TYPE_LINE_IJK | Line with IJK tool vector |
| FEAT_TYPE_RAPID | Rapid Move |
| FEAT_TYPE_CTOOL | CTool Marker |
| FEAT_TYPE_MARKER | CTool Marker |
| These variables are set by some of the macro commands | Description |
| PointRef | Reference number of point created |
| LineRef | Reference number of line created |
| CircleRef | Reference number of circle created |
| ContourRef | Reference number of contour created |
| SolidRef | Reference number of solid created |
| ExcelError | Error code set by all Excel commands (0 = no error) |
| ExcelCellLength | Length of text read from a cell in characters |
| FileError | Error code set by all file commands (0 = no error) |
| ReadVarsNumVars | Number of variables read using READ_NUM_VARS command |
| HoleFrError | Error code set by all HOLEFR commands (0 = no error) |
| CsNumber | Number of CS created |
| WgNumber | Number of WorkGroup created |
| Button | Number of button pressed on macro dialog (0 = OK button) |
The HOLEFR_GET_FEAT command sets these variables.
HOLEFR_GET_FEAT_Variables
| HOLEFR Variables | Description |
| HoleFrRef | Hole Feature Reference number |
| HoleFrType | Hole Type |
| HoleFrCS | Hole CS number |
| HoleFrRevCS | CS number for opposite direction |
| HoleFrThroughType | Though Hole Type |
| HoleFrDia | Overall Diameter |
| HoleFrDiaTop | Diameter at Top of Hole |
| HoleFrDepth | Total Depth |
| HoleFrMidDepth | Mid Depth |
| HoleFrFullDepth | Full Depth |
| HoleFrTopClear | Top Clearance Amount |
| HoleFrBottomClear | Bottom Clearance Amount |
| HoleFrTopZ | Top Z |
| HoleFrBottomZ | Bottom Z |
| HoleFrTop | Top |
| HoleFrBottom | Bottom |
| HoleFrWidth | Width |
| HoleFrAngle | Angle |
| HoleFrTipAngle | Tip Angle |
| HoleFrPosX | Hole Position |
| HoleFrPosY | measured at the |
| HoleFrPosZ | bottom of the hole |
| HoleFrPosTopX | Hole Position |
| HoleFrPosTopY | measured at the |
| HoleFrPosTopZ | top of the hole |
| HoleFrPosAxisX | Axis vector |
| HoleFrPosAxisY | measured from |
| HoleFrPosAxisZ | bottom to top |
| Floating Point Values | Description | Version Number |
| TYPE | Type (Mill, Lathe) | |
| UNITS | Inch (1) or Metric (0) | 12, 0, 31 |
| MATERIAL | Material code | |
| OFFSET | Offset number (diameter) | |
| SPINDLE_DIR | Spindle direction | |
| ID | Tool ID number | |
| USE_ID | 1 = Use ID is checked | |
| TOOL_GROUP_POS | TG position | |
| TOOL_GROUP | TG number | |
| PRIME_SPINDLE | Prime spindle number (removed in version 11) | |
| MTOOL_TYPE | Mill tool type | |
| MTOOL_NUM_FLUTES | Number of flutes | |
| MTOOL_LEN_OFFSET | Length offset number | |
| MTOOL_OPTIONS | Options is checked | |
| MTOOL_ORIENTATION | Orientation | |
| LTOOL_TYPE | Lathe tool type | |
| LTOOL_ISIZE | Insert size | |
| LTOOL_ORIENTATION | Orientation | |
| LTOOL_THREAD_STYLE | Thread style | |
| LTOOL_THREAD_TYPE | Thread type | |
| LTOOL_THREAD_ID_OD | ID or OD | |
| LTOOL_THREAD_DIR | Thread direction | |
| LTOOL_OFFSET | Lathe tool offset number | |
| LTOOL_CUT_SIDE | Cut side | |
| LTOOL_FACE_UP | 1 = Insert face up | |
| LTOOL_NEG_SIDE | 1 = Cut negative Side | |
| LTOOL_OTHER | Lathe tool type other | |
| MTOOL_HOLDER | Mill tool holder type | |
| LTOOL_HOLDER | Lathe tool holder type | |
| HOLDER_SOLID_REF | Solid number used for holder | |
| HOLDER_SHAPE_REF | Shape reference number of holder | |
| MTOOL_HOLDER_TYPE | Mill tool holder type | |
| FORM_SHAPE_REF | Form tool shape reference number | |
| TOOL_USE_SUB_POS | Does this tool use sub positions (1=yes) | 11, 3, 8 |
| LTOOL_HOLDER_ADAPT_BLOCK | Does this lathe tool use an adapter block (1=yes) | 11, 3, 8 |
| LTOOL_HOLDER_ATTACH_TYPE | Lathe holder attachment type | 11, 3, 8 |
| LTOOL_HAS_ALT_PRESET_PT | Does this lathe tool use 2 touch off points (1=yes) | 11, 3, 8 |
| LTOOL_WHICH_PRESET_PT | Which touch off point is active (0 or 1) | 11, 3, 8 |
| ATOOL_TYPE | Additive tool type | 13, 0, 18 |
| BTOOL_TYPE | Broaching tool type | 13, 0, 18 |
| MTOOL_SHANK_TYPE | Mill tool shank type (0, 1 or 2) | 14, 0, 26 |
| MTOOL_FPTHREAD_STYLE | Full Profile Threadmill thread style (0=UN, 1=UNJ, 2=ISO, 3=NPT, 4=Whitworth 55, 5=BSP) | 24, 0, 53 |
| Integer Values | Description | |
| MTOOL_LENGTH | Mill tool Length | |
| MTOOL_LEAD_TIP | Mill tool lead tip value | |
| MTOOL_TIP_RAD | Mill tool tip radius | |
| MTOOL_INNER_TOP_CORNER_RAD | Mill tool inner corner top radius | |
| MTOOL_BOTTOM_RAD | Mill tool bottom radius | |
| MTOOL_TOP_RAD | Mill tool top radius | |
| MTOOL_OUT_OF_HOLDER_LEN | Mill tool out of holder length | |
| LTOOL_SIZE | Lathe tool insert size | |
| LTOOL_THICK | Lathe tool insert thickness | |
| LTOOL_WIDTH | Lathe tool width | |
| LTOOL_LENGTH | Lathe tool length | |
| LTOOL_TIP_RAD | Lathe tool tip radius | |
| LTOOL_INSERT_ANGLE | Lathe tool insert angle | |
| LTOOL_TIP_OFFSET | Lathe tool tip offset | |
| LTOOL_PRESET_PT_X | Lathe tool preset point in X | |
| LTOOL_PRESET_PT_Z | Lathe tool preset point in X | |
| LTOOL_TURRET_SHIFT_X | Lathe tool turret shift in X | |
| LTOOL_TURRET_SHIFT_Z | Lathe tool turret shift in Z | |
| LTOOL_FACE_ANGLE | Lathe tool insert face angle | |
| LTOOL_SIDE_ANGLE | Lathe tool insert side angle | |
| LTOOL_TIP_WIDTH | lathe tool tip width | |
| LTOOL_TIP_ANGLE | Lathe tool tip angle | |
| LTOOL_THREAD_PITCH | Lathe tool thread pitch | |
| LTOOL_THREAD_FLAT_LEN | Lathe tool flat length | |
| LTOOL_THREAD_INSERT_WIDTH | Lathe tool insert width | |
| LTOOL_THREAD_EDGE_POS_X | Lathe tool edge position in X | |
| LTOOL_THREAD_EDGE_POS_Z | Lathe tool edge position in Z | |
| LTOOL_MID_ANGLE | Lathe tool mid angle | |
| LTOOL_TIP_CENTER_TO_PRESET_X | Lathe tool distance to preset X | |
| LTOOL_TIP_CENTER_TO_PRESET_Z | Lathe tool distance to preset Z | |
| LTOOL_FACE_RELIEF | Lathe tool face relief angle | |
| LTOOL_DIA_RELIEF | Lathe tool diameter relief angle | |
| LTOOL_HOLDER_THICKNESS | Lathe tool holder thickness | |
| LTOOL_B_AXIS | Lathe tool B axis angle | |
| LTOOL_UTIL_LEN | Lathe utility tool length | |
| LTOOL_UTIL_DIA | Lathe utility tool diameter | |
| LTOOL_UTIL_ANGLE | Lathe utility tool angle | |
| TOOL_PRESET_X | Tool preset position in X | |
| TOOL_PRESET_Y | Tool preset position in Y | |
| TOOL_PRESET_Z | Tool preset position in Z | |
| TOOL_TC_SHIFT_X | Tool turret shift in X | |
| TOOL_TC_SHIFT_Y | Tool turret shift in Y | |
| TOOL_TC_SHIFT_Z | Tool turret shift in Z |
| String Values | Description |
| COMMENT | Tool comment text |
| Parameter | Description | Version Number |
|---|---|---|
| TYPE | Process type | |
| MILL_TYPE | Mill process type | |
| LATHE_TYPE | Lathe process type | |
| ALLOW_TOOL | 1=Allow, 0=No Tool | 10.9.13 |
| TOOL_NUM | Tool number | |
| CRC | CRC state | |
| COOLANT | Coolant type | |
| CUT_TYPE | Cut type | |
| REPEATS | Number of repeats | |
| MTHREAD_TRAVERSE_CP1 | Thread Mill traverse CP1 | |
| MTHREAD_ID_OD | thread Mill ID or OD | |
| MTHREAD_THREAD_DIR | Thread Mill direction | |
| MTHREAD_RAPID_IN | Thread Mill rapid in | |
| SURFACE_TYPE | Surface process type | |
| SURFACE_CUT_TYPE | Cut type | |
| SURFACE_BACK_AND_FORTH | Back and Forth setting | |
| SURFACE_LACE_CUT_DIR | Lace cut direction | |
| SURFACE_OUTPUT_PREF | Output preference | |
| SURFACE_CUT_OPT | Cut option | |
| SURFACE_OFFSET_SURFACES | Offset surfaces | |
| SURFACE_ONE_PASS | One pass | |
| SURFACE_CONSTRAIN | Contrain state | |
| SURFACE_RETRACT_OPTION | Retract option | |
| SURFACE_STAY_IN_STOCK | Stay in stock | |
| SURFACE_CLEAR_STOCK | Clear stock | |
| SURFACE_CLEAR_STOCK_TYPE | Stock type | |
| SURFACE_CUT_OVER_EDGES | Cut over edges | |
| SURFACE_SKIP_FLATS | Skip flats | |
| CURVE_CUT_DIR | Cut direction | |
| SURFACE_FLOW_MACH_DIR | machining direction | |
| SURFACE_FLOW_MACH_Z_ORDER | Z order | |
| SURFACE_FLOW_TRAVEL_AROUND_MODE | Travel around mode | |
| SURFACE_FLOW_CUT_TYPE | Cut type | |
| SURFACE_INTERSECT_TYPE | Intersection type | |
| SURFACE_CUTS_TYPE | Cut type | |
| SURFACE_PASSES_TYPE | Passes type | |
| SURFACE_CLEANUP_TYPE | Cleanup type | |
| SURFACE_PASSES_PER_SIDE | Number of passes per side | |
| LATHE_PREFER_CANNED | Prefer canned option | |
| LATHE_CLEAR_ID | Clearance ID | |
| LROUGH_ROUND_CORNERS | Round corners | |
| LROUGH_CUT_OFF | Cut off | |
| LROUGH_CUT_DIR | Cut direction | |
| LROUGH_ENTRY_PERP | Entry perpendicular | |
| LROUGH_EXIT_PERP | Exit perpendicular | |
| LROUGH_ROUGH_TYPE | Rough cycle type | |
| LROUGH_CSS | Constant surface speed | |
| LROUGH_RAPID_STEP | Rapid step | |
| LROUGH_MONOTONIC | Is cycle path monotonic | |
| LROUGH_AVOID_AIR | Avoid air | |
| LROUGH_XPLUS | Cut in X plus direction | |
| LROUGH_XMINUS | Cut in X minus direction | |
| LROUGH_ZPLUS | Cut in Z plus direction | |
| LROUGH_ZMINUS | Cut in Z minus direction | |
| LROUGH_AUTO_FINISH | Auto finish option | |
| LROUGH_SPINDLE_DIR | Spindle direction | |
| LROUGH_FINISH_LAST | Finish last cut | |
| LROUGH_CENTER_OUT | Cut from center outwards | |
| LROUGH_CONSTANT_STEP | Constant step | |
| LROUGH_PECK | Peck value | |
| LROUGH_PLUNGE_TYPE | Plunge type | |
| LROUGH_CONSTANT_PATH | Constant path | |
| LROUGH_FIXED_SP | Fixed start point | |
| LROUGH_NUM_PASSES | Number of passes | |
| LROUGH_SHIFT_SQUARE_CORNERS | Shift square corners | |
| LROUGH_CLEANUP_PASS | Use a cleanup pass | |
| LROUGH_USE_DEFLECT_COMP | Use deflect compensation | |
| LROUGH_DEFLECT_COMP_VAL | Deflect compensation value | |
| LROUGH_MULTI_PASS | Multi pass | |
| LATHE_CUT_OTHER_SIDE | Can cut other side | |
| LATHE_USE_AUTO_CLEAR | Use auto clearance | |
| LTHREAD_SHAPE_METHOD | 0=From Parameters, 1=From Shape | 12.0.36 |
| LTHREAD_STYLE | Threading style | |
| LTHREAD_CUT_DIR | Cut direction | |
| LTHREAD_CUT_TYPE | Cut type | |
| LTHREAD_CSS | Constant Surface Speed | |
| LTHREAD_BALANCED_IN_FEED | Balanced in-feed | |
| LTHREAD_ALTERNATE | Alternate cuts | |
| LTHREAD_LAST_CUT | Last cut | |
| LTHREAD_NOMINAL_PITCH_INDEX | Nominal pitch index | |
| LTHREAD_TAPER_INDEX | Taper index | |
| LTHREAD_NUM_SPRING_PASSES | Number of spring passes | |
| LTHREAD_NUM_STARTS | Number of thread starts | |
| LDRILL_ENTRY | Lathe drill entry | |
| FEED_CONNECT | Use feed connect | |
| CRC_OFFSET | CRC offset number | |
| LEN_OFFSET | Length offset number | |
| CUSTOM_CBSET | Custom CBSET | |
| PATTERN_ON | Use a pattern | |
| PATTERN_INDEX | Pattern index | |
| ROUND_CORNERS | Round corners option | |
| ENTRY_PERP | Entry perpendicular | |
| EXIT_PERP | Exit perpendicular | |
| IGNORE_TOOLS | Ignore tools | |
| DEPTH_FIRST | Cut depth first | |
| SPRING_PASSES | Number of spring passes | |
| FM_USE_SHAPE | Use shape | |
| FM_HPLUS | H Plus value | |
| FM_VPLUS | V Plus value | |
| FM_MOVEH | Move Horizontal | |
| FM_BEFORE_ZIGZAG | Before ZigZag | |
| FM_BACK_AND_FORTH | Back and Forth | |
| FM_TYPE | FM type | |
| ENTRY_TYPE | Entry type | |
| START_ON_RIGHT | Start on the right | |
| RETRACTS | Use retracts | |
| HIT_PARALLEL | Hit parallel | |
| STAY_CLEAR | Stay clear | |
| CUT_BACK | Cut back | |
| SAME_STROKE | Same stroke | |
| FULL_DIA | Full diameter | |
| STEPOVER_FEED_LOCK | Stepover feed lock | |
| CLEAR_FEED_LOCK | Clear feed lock | |
| SCALLOP_FEED_LOCK | Scallop feed lock | |
| CLEAR_PERIPH | Clear periphery | |
| CS_NUM | CS number or process | |
| PATH_CS | CS number of toolpath | |
| POCKET_TYPE |
| |
| MILL_STAY_IN_STOCK | For checkbox "Use Stock" | |
| OFFSET_TRIM_OPTION | Offset trim options in roughing:
| |
| WALL_MODE | Wall mode | |
| PREFER_SUBS | Prefer subs option | |
| HIT_FLATS | Hit flats option | |
| POCKET_ENTRY_RAMP_TYPE | Ramp type | |
| POCKET_ENTRY_HELIX_TYPE | Helix type | |
| SURFACE_ENTRY_TYPE | Entry type | |
| SURFACE_ENTRY_RAMP_TYPE | Ramp type | |
| PROG_STOP | Program stop | |
| RAPID_IN | Rapid in | |
| MATERIAL_ONLY | material only cutting | |
| DRILL_TYPE | Drill type:
| |
| DRILL_POS_APPROACH | Drill position approach | |
| DRILL_CLEAR_PLANE | Drill clearance plane | |
| WALL_STEP | Wall step | |
| WALL_TOP_TO_BOTTOM | Top to Bottom | |
| WALL_SAME_DIR | Same direction | |
| WALL_SAME_DCEP_SIDE | Dcep side | |
| WALL_SWEPT_POCKET | Swept pocket | |
| WALL_SWEPT_ISLAND | Swept island | |
| S_USE_ADV_TOL | Use advance tolerance | |
| M_USE_ADV_TOL | Use advance tolerance | |
| CUT_SIDE | Cut side | |
| MD_FROM_TOOL | Modify depth from tool | |
| MD_VARY_WITH_GEO | Vary with geometry | |
| MD_VARY_WITH_FEAT | Vary with feature | |
| MD_RETRACT_LEVEL | Retract level | |
| MD_PROCESS_LOAD_H1Z_FEAT | Load H1 Feature Z | |
| CONTOUR_ENTRY_RAMP_TYPE | Ramp type | |
| CONTOUR_ENTRY_HELIX_TYPE | Helix type | |
| CONTOUR_RAMP_DOWN | 1=Ramp Down | 10.5.18 |
| CONTOUR_NUM_EXTRA_OFFSETS | Number of extra offsets | 10.5.18 |
| POCKET_OUTER_AS_BOSS | 1=Outer as Boss | 10.5.18 |
| WRAP | Wrap toolpath,same as option in Rotate tab
| |
| WRAP_NUM_COPIES | number of copies, same as option in Rotate tab | |
| DRILL_BORE_CUT_TYPE | Cut type | |
| ADV_EXIT_SAME_AS_ENTRY | 1=Exit values are same as entry | 10.2.22 |
| ADV_ENTRY_TYPE | Entry type | 10.2.22 |
| ADV_EXIT_TYPE | Exit type | 10.2.22 |
| ADV_LINE_ENTRY_USE_CRC | 1=Line Entry uses CRC | 10.2.22 |
| ADV_LINE_ENTRY_USE_OFF_PART_LINE | 1=Line Entry uses Off Part Line | 10.2.22 |
| ADV_LINE_ENTRY_USE_RAMP | 1=Line Entry uses Ramp | 10.2.22 |
| ADV_LINE_ENTRY_RAMP_INCLUDE_LINE | 1=Line Entry Ramp uses Include Line | 10.2.22 |
| ADV_LINE_EXIT_USE_CRC | 1=Line Exit uses CRC | 10.2.22 |
| ADV_LINE_EXIT_USE_OFF_PART_LINE | 1=Line Exit uses Off Part Line | 10.2.22 |
| ADV_LINE_EXIT_USE_RAMP | 1=Line Exit uses Ramp | 10.2.22 |
| ADV_LINE_EXIT_RAMP_INCLUDE_LINE | 1=Line Exit Ramp uses Include Line | 10.2.22 |
| ADV_ARC_ENTRY_USE_CRC | 1=Arc Entry uses CRC | 10.2.22 |
| ADV_ARC_ENTRY_USE_OFF_PART_LINE | 1=Arc Entry uses Off Part Line | 10.2.22 |
| ADV_ARC_ENTRY_USE_RAMP | 1=Arc Entry uses Ramp | 10.2.22 |
| ADV_ARC_ENTRY_RAMP_INCLUDE_RADIUS | 1=Arc Entry Ramp uses Include Radius | 10.2.22 |
| ADV_ARC_EXIT_USE_CRC | 1=Arc Exit uses CRC | 10.2.22 |
| ADV_ARC_EXIT_USE_OFF_PART_LINE | 1=Arc Exit uses Off Part Line | 10.2.22 |
| ADV_ARC_EXIT_USE_RAMP | 1=Arc Exit uses Ramp | 10.2.22 |
| ADV_ARC_EXIT_RAMP_INCLUDE_RADIUS | 1=Arc Exit Ramp uses Include Radius | 10.2.22 |
| PROC_ID | Process ID Number | 10.2.22 |
| LROUGH_USE_END_LIMIT | lathe Rough uses End Limit | 10.2.22 |
| DRILL_REVERSE_ORDER | Drill cycle has Reverse Order checked | 10.2.22 |
| BAXIS_USED | B Axis Turning is used | 10.2.22 |
| BAXIS_METHOD | B Axis Turning Method | 10.2.22 |
| BAXIS_MULTI_TRANS | B Axis Turning uses multiple transitions | 10.2.22 |
| BAXIS_USE_MIN_ANGLE | B Axis Turning Minimum Angle | 10.2.22 |
| BAXIS_USE_MAX_ANGLE | B Axis Turning Maximum Angle | 10.2.22 |
| BAXIS_SMOOTH_CORNERS | B Axis Turning uses Smooth Corners option | 10.2.22 |
| BAXIS_VECTOR_TYPE | B Axis Turning Vector Type | 10.2.22 |
| BAXIS_CHECK_COLLISIONS | B Axis Turning uses Collision Checking | 10.2.22 |
| UTIL_TYPE | Utility Process Type | 10.2.22 |
| THREAD_MILL_RAPID_TO_FROM_CLEAR | 1=Rapid to/from Clearance Diameter | 10.3.11 |
| THREAD_MILL_PLUNGE_AT_CENTER | 0=Plunge at center, 1=Plunge at Diameter | 10.3.11 |
| THREAD_MILL_VARY_WITH_GEO | 1=Vary depth with geometry | 10.3.11 |
| THREAD_MILL_ENTRY_EXIT_METHOD | Entry/Exit method | 10.3.11 |
| THREAD_MILL_ENTRY_EXIT_RAD | Entry/Exit radius | 10.3.11 |
| THREAD_MILL_CUT_TYPE | 0=One Top Pass, 1=One Finish Pass, 3=Const Cut 3=Const Load | 10.3.11 |
| THREAD_MILL_DO_LAST_CUT | 1=Specify exact depth of last cut | 10.3.11 |
| THREAD_MILL_NUM_SPRING_PASSES | Number of Spring Passes | 10.3.11 |
| THREAD_MILL_START_DEPTH_TYPE | 0=Abs Z, 1=Top of Hole, 2=Seg Start, 3=Seg End | 10.3.11 |
| THREAD_MILL_END_DEPTH_TYPE | 0=Top, 1=Chamfer, 2=Mid, 3=Bottom, 4=Seg start, 5=Seg end, 6=Abs | 10.3.11 |
| THREAD_MILL_START_SEGNUM | Start Depth Segment Number | 10.3.11 |
| THREAD_MILL_END_SEGNUM | End Depth Segment Number | 10.3.11 |
| THREAD_MILL_SEGMENT_MATCH | 1=Use Segment Matching | 10.3.11 |
| THREAD_MILL_SEG_MATCH_LEN | 1=Match Segment Length | 10.3.11 |
| THREAD_MILL_SEG_MATCH_DIA | 1=Match Segment Diameter | 10.3.11 |
| THREAD_MILL_SEG_MATCH_TAPER | 1=Match Segment Taper | 10.3.11 |
| THREAD_MILL_SEG_MATCH_METHOD | 1=Match Segment Method | 10.3.11 |
| THREAD_MILL_DIM_FROM_TOOL | 0=Dimension from Hole, 1=Dimension from Tool | 10.3.11 |
| THREAD_MILL_BOTTOM_UP | 0=Top down, 1=Bottom Up | 10.3.11 |
| MULTI_SHAPE_SINGLE_SHAPE_USE_MARKERS | 1=Use Markers, 0=Do not use markers | 12.0.28 |
| MULTI_SHAPE_CENTERLINE | 1=Use Markers, 0=Do not use markers | 12.0.28 |
| MULTI_SHAPE_CLOSED_INSIDE | 1=Tool inside, 0=Tool outside | 12.0.28 |
| MULTI_SHAPE_CLOSED_ALTERNATE_SIDES | 1 = Alternate tool side for nested shapes | 12.0.28 |
| MULTI_SHAPE_OPEN_START_EXTENSION | start extension | |
| MULTI_SHAPE_OPEN_END_EXTENSION | end extension | |
| COMMENT_LEN | Process comment length | 14.0.33 |
| LATHE_OD_ID_FACE | Lathe Approach Type: 0=OD, 1=ID Front, 2=ID Rear (if applicable), 3=Rear Face (if applicable) | -- |
| MCUTOFF_STYLE | Mill Cutoff style (saw or end mill) | 25.0.25 |
| MCUTOFF_STRATEGY | Cutting Strategy (sprial, single cut, two cuts same dir, two cuts back and forth) | 25.0.25 |
| MCUTOFF_PASS_DIR | Cur Direction (X or Y) only applicable to Saw Style and not spiral cutting stragegy | 25.0.25 |
| MCUTOFF_SPIRAL_DIR | spiral direction (CW or CCW) | 25.0.25 |
| MCUTOFF_RETRACT_TO_SURFACE_RAD | Retract to surface radius (only valid for sprial) | 25.0.25 |
| MCUTOFF_USE_ROTARY | use rotary or use position (like the rotate tab) | 25.0.25 |
| Parameter | Description | Version Number |
|---|---|---|
| ENTRY_CLEAR | Entry clerance height | |
| EXIT_CLEAR | Exit clearance height | |
| ENTRY_LINE | Entry line length | |
| EXIT_LINE | Exit line length | |
| ENTRY_RAD | Entry radius | |
| EXIT_RAD | Exit radius | |
| ENTRY_FEED | Entry feedrate | |
| CONTOUR_FEED | Contour feedrate | |
| SURF_Z | Surface Z | |
| SURFACE_Z | Surface Z | |
| TIP_Z | Tip Z (depth) | |
| Z_STEP_WANTED | Z step desired | |
| CUT_WIDTH | Cut width | |
| STOCK | Stock amount | |
| BOSS_STOCK | Boss stock amount | |
| OVERHANG | Overhang amount | |
| OVERLAP | Overlap amount | |
| OPEN_CLEARANCE | Open clearance amount | |
| MTHREAD_START_THREAD | Thread Mill start | |
| MTHREAD_END_THREAD | Thread Mill end | |
| MTHREAD_CUT_DIA | Thread Mill cut diameter | |
| MTHREAD_CLEAR_DIA | Thread Mill clearance diameter | |
| MTHREAD_PITCH | Thread Mill pitch | |
| MTHREAD_FEED | Thread Mill feedrate | |
| SURFACE_EFEED | Surface entry feedrate | |
| SURFACE_CFEED | Surface contour feedrate | |
| SURFACE_STOCK | Surface stock amount | |
| SURFACE_FIXTURE_CLEAR | Surface fixture clearance | |
| SURFACE_STEPOVER | Surface stepover | |
| SURFACE_RIDGE_HEIGHT | Surface ridge height | |
| SURFACE_CUT_ANGLE | Surface cut angle | |
| SURFACE_DESIRED_Z | Surface desired Z step | |
| SURFACE_CONST_FACES_CLEAR | Surface constant faces clearance | |
| SURFACE_CUT_TOL | Surface cut tolerance | |
| SURFACE_STOCK_TOL | Surface stock tolerance | |
| SURFACE_FIXTURE_TOL | Surface fixture tolerance | |
| SURFACE_CONSTRAINT_TOL | Surface constraint tolerance | |
| SURFACE_SMOOTH_TOL | Surface smoothing tolerance | |
| SURFACE_ARC_FIT_TOL | Surface arc fit tolerance | |
| SURFACE_SPLINE_APPROX_TOL | Surface spline approximation tolerance | |
| SURFACE_NORMAL_ANGLE | Surface normal angle | |
| SURFACE_STEP_CUT_RATIO | Surface step cut ratio | |
| SURFACE_CORNER_RAD | Surface corner radius | |
| SURFACE_MAX_CUT_ANGLE | Surface maximum cut angle | |
| LROUGH_START_SIDE_EXT | Lathe rough side extension | |
| LROUGH_MIN_RAD | Lathe rough minimum radius | |
| LROUGH_STOCK | Lathe rough stock amount | |
| LROUGH_STOCK_X | Lathe rough stock in X | |
| LROUGH_STOCK_Z | Lathe rough stock in Z | |
| LROUGH_ENTRY_LINE | Lathe rough entry line length | |
| LROUGH_ENTRY_RAD | Lathe rough entry arc radius | |
| LROUGH_EXIT_RAD | Lathe rough exit arc radius | |
| LROUGH_EXIT_LINE | Lathe rough exit line length | |
| LROUGH_ROUGH_START | Lathe rough start amount | |
| LROUGH_MAX_RPM | Lathe rough maximum RPM | |
| LROUGH_SFPM | Lathe rough Surface Speed | |
| LROUGH_FEED | Lathe rough feedrate | |
| LROUGH_CLEARANCE | Lathe rough clearance amount | |
| LROUGH_ENTRY_FEED | Lathe rough entry feedrate | |
| LROUGH_CONTOUR_FEED | Lathe rough contour feedrate | |
| LROUGH_AUTO_FINISH_FEED | Lathe rough auto finish feedrate | |
| LROUGH_TURN_CUT_WIDTH | Lathe rough cut width | |
| LROUGH_RAMP_ANGLE | Lathe rough ramp angle | |
| LROUGH_PLUNGE_TYPE | Lathe rough plunge type | |
| LROUGH_PLUNGE_FIRST | Lathe rough first | |
| LROUGH_DIR_FWD | Lathe rough direction fwd | |
| LROUGH_BACK_AND_FORTH | Lathe rough back and forth | |
| LROUGH_PLUNGE_ANGLE | Lathe rough plunge angle | |
| LROUGH_CUT_WIDTH | Lathe rough cut width | |
| LROUGH_FEED_PERCENT | Lathe rough feed percentage | |
| LROUGH_PECK | Lathe rough peck value | |
| LROUGH_RETRACT | Lathe rough retract value | |
| LROUGH_CUT_X | Lathe rough cut in X | |
| LROUGH_CUT_Z | Lathe rough cut in Z | |
| LROUGH_SHIFT_CUT_WIDTH | Lathe rough shift cut width | |
| LROUGH_CYCLE_SP_X | Lathe rough cycle start point in X | |
| LROUGH_CYCLE_SP_Z | Lathe rough cycle start point in Z | |
| LROUGH_OFFSET_CUT_DEPTH | Lathe rough offset cycle cut depth | |
| LTHREAD_RPM | Lathe thread cycle spindle speed RPM | 11.0.4 |
| LTHREAD_Z_START | Lathe thread cycle Z start | |
| LTHREAD_Z_END | Lathe thread cycle Z end | |
| LTHREAD_NOMINAL | Lathe thread cycle nominal pitch | |
| LTHREAD_PITCH | Lathe thread cycle pitch | |
| LTHREAD_MAJOR_DIA | Lathe thread cycle major diameter | |
| LTHREAD_MINOR_DIA | Lathe thread cycle minor diameter | |
| LTHREAD_THREAD_HEIGHT | Lathe thread cycle height | |
| LTHREAD_TAPER | Lathe thread cycle taper amount | |
| LTHREAD_THREAD_ANGLE | Lathe thread cycle angle | |
| LTHREAD_CUT_DEPTH | Lathe thread cycle cut depth | |
| LTHREAD_LAST_CUT | Lathe thread cycle last cut | |
| LTHREAD_Z_START_EXTEND | Lathe thread cycle Z start extension | |
| LTHREAD_Z_END_EXTEND | Lathe thread cycle Z end extension | |
| LTHREAD_X_START_EXTEND | Lathe thread cycle X start extension | |
| LTHREAD_X_END_EXTEND | Lathe thread cycle X end extension | |
| LDRILL_DWELL | Lathe drill cycle dwell amount | |
| LDRILL_PECK | Lathe drill cycle peck value | |
| LDRILL_CLEARANCE | Lathe drill cycle clearance | |
| LDRILL_RETRACT | Lathe drill cycle retract value | |
| LDRILL_TAP_PERCENT | Lathe drill cycle tap percentage | |
| LDRILL_FEED | Lathe drill cycle feedrate | |
| LDRILL_TIP_Z | Lathe drill cycle tip Z (end position) | |
| LDRILL_SURFACE_Z | Lathe drill cycle surface Z (start position) | |
| TOOL_CHANGE | Tool change | |
| CP1 | CP1 value | |
| CURVE_TOL | Curve tolerance | |
| AUTO_ENTRY_CP | Auto entry CP | |
| AUTO_ENTRY_CLEAR_RAD | Auto entry clear radius | |
| AUTO_EXIT_CP | Auto exit CP | |
| AUTO_EXIT_CLEAR_RAD | Auto exit clear radius | |
| AXIS_INFO | Axis info | |
| GEO_RAD | Geometry radius | |
| MIN_RAD | Minimum radius | |
| Z_STEP | Actual Z step | |
| FM_CLEAR | Clearance | |
| FM_CUT_WIDTH | Cut width | |
| CUT_ANGLE | Cut angle | |
| STEPOVER_FEED | Stepover feed | |
| CLEAR_FEED | Clearance feed | |
| SCALLOP_FEED | Scallop feed | |
| MIN_CUT | Minimum cut | |
| RPM | Spindle speed | |
| RPMS | Spindle speed | |
| DRILL_FEED | Drill feedrate | |
| PAST_STOCK | Past stock amount | |
| POCKET_ENTRY_PLUNGE_PT_X | Plunge point in X | |
| POCKET_ENTRY_PLUNGE_PT_Y | Plunge point in Y | |
| POCKET_ENTRY_RAMP_SLOPE | Ramp slope | |
| POCKET_ENTRY_RAMP_START_Z | Ramp start in Z | |
| POCKET_ENTRY_RAMP_MAX_CUT | Ramp maximum cut | |
| POCKET_ENTRY_RAMP_WALL_CLEAR | Ramp wall clearance | |
| POCKET_ENTRY_RAMP_ANGLE | Ramp angle | |
| POCKET_ENTRY_HELIX_SLOPE | Entry helix slope | |
| POCKET_ENTRY_HELIX_ANGLE | Entry helix angle | |
| POCKET_ENTRY_HELIX_START_Z | Entry helix start in z | |
| POCKET_ENTRY_HELIX_MAX_CUT | Entry helix maximimum cut | |
| POCKET_ENTRY_HELIX_WALL_CLEAR | Entry helix wall clearance | |
| POCKET_ENTRY_HELIX_DIA | Entry helix diameter | |
| POCKET_ENTRY_HELIX_CP_X | Entry helix CP in X | |
| POCKET_ENTRY_HELIX_CP_X | Entry helix CP in Y | |
| POCKET_ENTRY_PERIPH_START_Z | Entry peripheral start in Z | |
| POCKET_ENTRY_PERIPH_SLOPE | Entry periphery slope | |
| SURFACE_ENTRY_PLUNGE_PT_X | Entry Plunge point in X | |
| SURFACE_ENTRY_PLUNGE_PT_Y | Entry Plunge point in Y | |
| RAPID_CLEARANCE | Rapid clearance amount | |
| CONTOUR_SURFACE_STOCK | Contour surface stock | 12.0.29 |
| POCKET_SURFACE_STOCK | Pocket surface stock | 12.0.29 |
| DRILL_DWELL | Drill cycle dwell amount | |
| DRILL_PECK_PERCENT | Peck depth as a percentage of tool diameter | 12.0.36 |
| DRILL_PECK_VALUE | Peck depth value | 12.0.36 |
| DRILL_PECK_CLEARANCE | Drill cycle peck clearance amount | |
| DRILL_TAP_PERCENT | Drill cycle tap percentage | |
| DRILL_BORE_PULLOFF | Drill cycle bore pulloff amount | |
| DRILL_PECK_RETRACT | Drill cycle peck retract amount | |
| WALL_TOP | Wall top | |
| WALL_ANGLE | Wall angle | |
| WALL_BOTTOM | Wall bottom | |
| WALLI_TOP | Wall (internal) top | |
| WALLI_ANGLE | Wall (internal) angle | |
| WALLI_BOTTOM | Wall (internal) bottom | |
| WALL_USER_STEP | Wall user step | |
| WALL_SHAPE_STEP | Wall shape step | |
| WALL_RIDGE_HEIGHT | Wall ridge height | |
| MSURF_CLEAR | Clearance amount | |
| MSURFACE_CLEAR | Clearance amount | |
| MSTOCK_TOL | Stock tolerance | |
| MFIX_TOL | Fixture tolerance | |
| MFIXTURE_TOL | Fixture tolerance | |
| MZSHIFT | Z shift amount | |
| CONTOUR_EXTRA_OFFSETS_VAL | Extra offsets values | 10.5.18 |
| CONTOUR_ENTRY_RAMP_SLOPE | Contour process entry ramp slope | |
| CONTOUR_ENTRY_RAMP_START_Z | Contour process entry ramp start in Z | |
| CONTOUR_ENTRY_RAMP_MAX_CUT | Contour process entry ramp maximum cut | |
| CONTOUR_ENTRY_RAMP_ANGLE | Contour process entry ramp angle | |
| CONTOUR_ENTRY_HELIX_SLOPE | Contour process entry helix slope | |
| CONTOUR_ENTRY_HELIX_START_Z | Contour process entry helix start in Z | |
| CONTOUR_ENTRY_HELIX_MAX_CUT | Contour process entry helix maximum cut | |
| CONTOUR_ENTRY_HELIX_DIA | Contour process entry helix diameter | |
| WRAP_START_ANGLE | Wrap start angle,same as option in Rotate tab | |
| WRAP_NUM_COPIES | Wrap number of duplications,same as option in Rotate tab | |
| WRAP_COPY_ANGLE | Wrap duplication angle,same as option in Rotate tab | |
| ADV_LINE_ENTRY_CRC | Advanced line entry CRC | |
| ADV_LINE_EXIT_CRC | Advanced line exit CRC | |
| ADV_ARC_ENTRY_CRC | Advanced arc entry CRC | |
| ADV_ARC_ENTRY_RAD | Advanced arc entry radius | |
| ADV_ARC_EXIT_CRC | Advanced arc exit CRC | |
| ADV_ARC_EXIT_RAD | Advanced arc exit radius | |
| DRILL_BORE_CUT_DIA | Drill bore cut diameter | |
| DRILL_BORE_CLEAR_DIA | Drill bore clear diameter | |
| DRILL_BORE_CLEAR_AMOUNT | Drill bore clear amount | |
| DRILL_BORE_ENTRY_EXIT_RAD | Drill bore entry exit radius | |
| DRILL_BORE_ENTRY_EXIT_LINE | Drill bore entry exit line length | |
| DRILL_BORE_CUT_WIDTH | Drill bore cut width | |
| DRILL_BORE_STOCK | Drill bore stock amount | |
| DRILL_BORE_OVERLAP | Drill bore overlap amount | |
| DRILL_BORE_APPROACH_ANGLE | Drill bore approach angle | |
| DRILL_BORE_DESIRED_STEP | Drill bore desired step amount | |
| ADV_LINE_ENTRY_OFF_PART_LINE | Line Entry Off Part Line value | 10.2.22 |
| ADV_LINE_ENTRY_OFF_PART_ANGLE | Line Entry Off Part Line angle | 10.2.22 |
| ADV_LINE_ENTRY_OFF_PART_DIST | Line Entry Off Part distance | 10.2.22 |
| ADV_LINE_ENTRY_RAMP_DIST | Line Entry Ramp distance | 10.2.22 |
| ADV_LINE_EXIT_OFF_PART_LINE | Line Exit Off Part Line value | 10.2.22 |
| ADV_LINE_EXIT_OFF_PART_ANGLE | Line Exit Off Part Line angle | 10.2.22 |
| ADV_LINE_EXIT_OFF_PART_DIST | Line Exit Off Part distance | 10.2.22 |
| ADV_LINE_EXIT_RAMP_DIST | Line Exit Ramp distance | 10.2.22 |
| ADV_ARC_ENTRY_OFF_PART_LINE | Arc Entry Off Part Line value | 10.2.22 |
| ADV_ARC_ENTRY_OFF_PART_DIST | Arc Entry Off Part distance | 10.2.22 |
| ADV_ARC_ENTRY_RAMP_DIST | Arc Entry Ramp distance | 10.2.22 |
| ADV_ARC_EXIT_OFF_PART_LINE | Arc Exit Off Part Line value | 10.2.22 |
| ADV_ARC_EXIT_OFF_PART_DIST | Arc Exit Off Part distance | 10.2.22 |
| ADV_ARC_EXIT_RAMP_DIST | Arc Exit Ramp distance | 10.2.22 |
| LROUGH_END_LIMIT_VAL | lathe Roughing End Limit Value | 10.2.22 |
| BAXIS_MIN_ANGLE_VAL | B Axis Turning, Minimum Angle | 10.2.22 |
| BAXIS_MAX_ANGLE_VAL | B Axis Turning, Maximum Angle | 10.2.22 |
| BAXIS_LEAD_LAG_ANGLE | B Axis Turning, Lead Lag Angle | 10.2.22 |
| BAXIS_COLLISION_CLEARANCE | B Axis Turning, Collision Check Clearance | 10.2.22 |
| THREAD_WHIRL_NUM_FLUTES | Number of Flutes | 10.2.22 |
| THREAD_WHIRL_FEED_PER_FLUTE | Feed Per Flute | 10.2.22 |
| THREAD_WHIRL_FEED | Feed | 10.2.22 |
| THREAD_WHIRL_PITCH | Pitch (mm) | 10.2.22 |
| THREAD_WHIRL_RPM | Spindle Speed | 10.2.22 |
| THREAD_WHIRL_CP2 | Entry Clear Z | 10.2.22 |
| THREAD_WHIRL_CP3 | Exit Clear Z | 10.2.22 |
| THREAD_WHIRL_IN_X | Run In X | 10.2.22 |
| THREAD_WHIRL_IN_Z | Run In Z | 10.2.22 |
| THREAD_WHIRL_OUT_X | Run Out X | 10.2.22 |
| THREAD_WHIRL_OUT_Z | Run Out Z | 10.2.22 |
| THREAD_WHIRL_START_X | Start X | 10.2.22 |
| THREAD_WHIRL_START_Z | Start Z | 10.2.22 |
| THREAD_WHIRL_END_X | End X | 10.2.22 |
| THREAD_WHIRL_END_Z | End Z | 10.2.22 |
| THREAD_WHIRL_APP_X | Approach X | 10.2.22 |
| THREAD_WHIRL_APP_Z | Approach Z | 10.2.22 |
| THREAD_WHIRL_RET_X | Retract X | 10.2.22 |
| THREAD_WHIRL_RET_Z | Retract Z | 10.2.22 |
| THREAD_WHIRL_COOLANT | Coolant Type | 10.2.22 |
| THREAD_WHIRL_CONST_FEED_ON | 1=Constant Feed On | 10.2.22 |
| THREAD_WHIRL_CONST_FEED_VAL | Constant Feed value | 10.2.22 |
| THREAD_WHIRL_C_OFFSET | Type of C Offset | 10.2.22 |
| THREAD_WHIRL_START_C_OFFSET | C Offset Start | 10.2.22 |
| THREAD_WHIRL_END_C_OFFSET | C Offset End | 10.2.22 |
| THREAD_MILL_PLUNGE_DIA | Plunge diameter | 10.3.11 |
| THREAD_MILL_ENTRY_FEED | Entry feedrate | 10.3.11 |
| THREAD_MILL_CRC_LINE | CRC line length | 10.3.11 |
| THREAD_MILL_ENTRY_ANGLE | Entry angle | 10.3.11 |
| THREAD_MILL_EXIT_ANGLE | Exit angle | 10.3.11 |
| THREAD_MILL_ENTRY_EXIT_RAD | Entry/Exit radius | 10.3.11 |
| THREAD_MILL_THREAD_HEIGHT | Thread height | 10.3.11 |
| THREAD_MILL_CUT_DEPTH | Depth of first cut | 10.3.11 |
| THREAD_MILL_LAST_CUT_AMOUNT | Last cut amount | 10.3.11 |
| THREAD_MILL_TAPER_ANGLE | Taper angle | 10.3.11 |
| THREAD_MILL_ADJUST_DEPTH_DELTA | Amount to adjust end depth | 10.3.11 |
| THREAD_MILL_START_DEPTH | Start depth Z | 10.3.11 |
| THREAD_MILL_END_DEPTH | End depth Z | 10.3.11 |
| MULTI_SHAPE_OPEN_END_EXTENSION | End extension value | 25.0.25 |
| MCUTOFF_DEPTH_OF_CUT | depth position based on part origin to use for cutoff | 12.0.28 |
| MCUTOFF_POSITION_OF_CUT | Cut off position based on part origin specified on cutoff part side | 25.0.25 |
| MCUTOFF_START_POSITION | start position of the tool before the cut along the cut direction | 25.0.25 |
| MCUTOFF_END_POSITION | end position of the tool after the cut along the cut direction | 25.0.25 |
| MCUTOFF_TWOCUT_OVERLAP | depth position beyond the origin the tool will use for each pass | 25.0.25 |
| MCUTOFF_SPIRAL_CENTER_PT_X | X center point of spiral | 25.0.25 |
| MCUTOFF_SPIRAL_CENTER_PT_Y | Y center point of spiral | 25.0.25 |
| MCUTOFF_SPIRAL_RAD | material radius for the | 25.0.25 |
| MCUTOFF_SPIRAL_MAX_CUT | maximum cut depth the tool will take | 25.0.25 |
| MCUTOFF_SPIRAL_OVERCUT_DEPTH | material diameter for the cut, the spiral will cut from the surface to the center | 25.0.25 |
| String Values | Description |
| COMMENT | Comment text |
| Integer Values | Description | Floating Point Values | Description |
|---|---|---|---|
| FLOW_NUM | Flow number | TIME | Time |
| SPINDLE_NUM | Spindle number | SPINDLE_SPEED | Spindle speed |
| MACHINE_MODE | Machine mode | X_POSITION | X position |
| FROM_WORKPIECE | From workpiece | Z_POSITION | Z position |
| TO_WORKPIECE | To workpiece | X_CLEARANCE | X clearance amount |
| SPINDLE_ON | Spindle on | Z_CLEARANCE | Z clearance amount |
| FORWARD | Cut forward | X_VALUE | X value |
| X_HOME | X home | Z_VALUE | Z value |
| Z_HOME | Z home | X_DROP | X drop |
| PART_IN_MAIN | Part is in main spindle | Z_DROP | Z drop |
| PART_IN_SUB | Part is in sub spindle | FEEDRATE | Feedrate |
| C_SYNCHED | C synchronized | FEED_DISTANCE | Feed distance |
| SUB_IN_UNLOAD | Sub spindle in unload | INITIAL_FACE_Z | Initial face Z |
| TORQUE_SENSING | Torch sensing | GRIP_Z | Grip Z value |
| LOCATION | Location | SHIFT_DISTANCE | Shift distance amount |
| ORIENTATION | Orientation | TORQUE_VAL | Torque value |
| FULL_RETURN | Full return | PULLBACK | Pullback amount |
| AUTO_REMOVE | Auto remove | C_SHIFT_ANGLE | C Shift Angle |
| SPINDLE_UNLOADED | Spindle is unloaded | ||
| CS | CS number | ||
| CONTROL_POINT | Control point (Tooltip) |
| Integer Values | Description | Floating Point Values | Description |
|---|---|---|---|
| TYPE | ENTRY_CLEAR | ||
| MILL_TYPE | EXIT_CLEAR | ||
| LATHE_TYPE | ENTRY_FEED | ||
| TOOL_NUM | CONTOUR_FEED | ||
| PROC_GROUP | CUT_WIDTH | ||
| PROC_ID | DRILL_CLEAR_PLANE | ||
| PROC_OP | STOCK | ||
| WG_NUM | BOSS_STOCK | ||
| CS_NUM | RPM | ||
| PATH_CS | RPMS | ||
| LOCKS | TIME | ||
| NUM_REPEATS | LENGTH | ||
| CRC_DIR | CSS | ||
| CRC_OFFSET | SURFACE_STOCK | ||
| LEN_OFFSET | SURF_STOCK | ||
| COOLANT | LATHE_XZ_STOCK | ||
| CUT_TYPE | LATHE_CUT_WIDTH | ||
| CSS | CUT_TOL | ||
| CRC_SIDE | STEP | ||
| DRILL_TYPE | DEPTH | ||
| DRILL_CLEAR_PLANE | OD_ID_FACE | ||
| DRILL_POS_APPROACH | LATHE_DEPTH | ||
| MATERIAL_ONLY | DRILL_DWELL | ||
| RAPID_IN | DRILL_TAP_PERCENT | ||
| LTHREAD_BALANCED | DRILL_PECK_CLEARANCE | ||
| LTHREAD_ANGLE_ALT | DRILL_PECK_AMOUNT | ||
| LTHREAD_STARTS | DRILL_PECK_RETRACT | ||
| LTHREAD_LAST_CUT | DRILL_BORE_PULLOFF | ||
| LATHE_PREFER_CANNED | DRILL_CB_START_RIZ | ||
| LATHE_CANNED_AUTOFIN | DRILL_CB_END_RIZ | ||
| LTHREAD_TYPE | SURRFACE_DEPTH | ||
| LATHE_CUT_DIR | MATERIAL_ONLY_CLEARANCE | ||
| NUM_SPRING_PASSES | LTHREAD_ANGLE | ||
| LATHE_ROUGH_TYPE | LTHREAD_NOMINAL_XD | ||
| LATHE_PULL_OFF_WALL | LTHREAD_TPI | ||
| LATHE_PLUNGE_CUT_TYPE | LTHREAD_PITCH | ||
| LATHE_PLUNGE_CENTER_OUT | LTHREAD_SLOPE | ||
| LATHE_PLUNGE_TYPE | LTHREAD_MINOR_XD | ||
| LATHE_PLUNGE_ENTRY_TYPE | LTHREAD_HEIGHT_XR | ||
| LATHE_PAT_SHIFT_FIXED_SRT | LTHREAD_RUN_IN | ||
| LATHE_PAT_SHIFT_PASSES | LTHREAD_RUN_OUT | ||
| LATHE_SQUARE_CORNERS | LTHREAD_FIRST_CUT | ||
| LATHE_NO_DRAG | LTHREAD_LAST_CUT | ||
| LATHE_CUT_OFF | LPLUNGE_MAX_CUT | ||
| LATHE_OD_ID_FACE | LPLUNGE_ANGLE | ||
| WRAP | LPLUNGE_PECK_AMOUNT | ||
| WRAP_DUPS | LPLUNGE_PECK_CLEARANCE | ||
| PROG_STOP | LPLUNGE_PECK_RETRACT | ||
| POCKET_TYPE | LPLUNGE_FEED_PERCENT | ||
| TOOL_GROUP | LATHE_PATTERN_SHIFT_CUT | ||
| WORKPIECE | LATHE_PATTERN_SHIFT_POINT | ||
| FLOW | WRAP_START_ANGLE | ||
| SPIN_CONTROL | WRAP_DUP_ANGLE | ||
| LATHE_CUT_OTHER_SIDE | LATHE_MAX_RPM | ||
| POCKET_ENTRY_RAMP | POCKET_ENTRY_PLUNGE_POINT | ||
| POCKET_ENTRY_HELIX_TYPE | POCKET_ENTRY_RAMP_SLOPE | ||
| SURFACE_ENTRY_TYPE | POCKET_ENTRY_RAMP_START_Z | ||
| SURFACE_ENTRY_RAMP_TYPE | POCKET_ENTRY_RAMP_MAX_CUT | ||
| MACH_ENGINE | POCKET_ENTRY_RAMP_WALL_CLEAR | ||
| FEED_CONNECT | POCKET_ENTRY_RAMP_ANGLE | ||
| CRC_OFFSET | POCKET_ENTRY_HELIX_SLOPE | ||
| PATTERN_ON | POCKET_ENTRY_HELIX_ANGLE | ||
| PATTERN_INDEX | POCKET_ENTRY_HELIX_START_Z | ||
| ROUND_CORNERS | POCKET_ENTRY_HELIX_MAX_CUT | ||
| ENTRY_PERP | POCKET_ENTRY_HELIX_WALL_CLEAR | ||
| EXIT_PERP | POCKET_ENTRY_HELIX_DIA | ||
| IGNORE_TOOLS | POCKET_ENTRY_HELIX_CP | ||
| DEPTH_FIRST | POCKET_ENTRY_PERIPH_START_Z | ||
| FM_USE_SHAPE | POCKET_ENTRY_PERIPH_SLOPE | ||
| FM_HPLUS | SURFACE_ENTRY_PLUNGE_PT | ||
| FM_VPLUS | RAPID_CLEARANCE | ||
| FM_MOVEH | ENTRY_LINE_LEN | ||
| ZIG_ZAG | EXIT_LINE_LEN | ||
| BACK_FORTH | ENTRY_RAD | ||
| FM_TYPE | EXIT_RAD | ||
| ENTRY_TYPE | Z_STEP_WANTED | ||
| START_ON_RIGHT | OVERHANG | ||
| RETRACTS | OVERLAP | ||
| HIT_PARALLEL | OPEN_CLEARANCE | ||
| STAY_CLEAR | MTHREAD_START_THREAD | ||
| CUT_BACK | MTHREAD_END_THREAD | ||
| SAME_STROKE | MTHREAD_CUT_DIA | ||
| FULL_DIA | MTHREAD_CLEAR_DIA | ||
| STEPOVER_FEED_LOCK | MTHREAD_PITCH | ||
| CLEAR_FEED_LOCK | MTHREAD_FEED | ||
| SCALLOP_FEED_LOCK | SURFACE_STEP_OVER | ||
| CLEAR_PERIPH | SURFACE_RIDGE_HEIGHT | ||
| HIT_FLATS | SURFACE_CUT_ANGLE | ||
| MTHREAD_TRAVERSE_CP1 | SURFACE_DESIRED_Z | ||
| MTHREAD_ID_OD | SURFACE_CONSTRAINT_FACES_CLEAR | ||
| MTHREAD_THREAD_DIR | SURFACE_STOCK_TOL | ||
| SURFACE_TYPE | SURFACE_FIX_TOL | ||
| SURFACE_CUT_TYPE | SURFACE_FIXTURE_TOL | ||
| SURFACE_BACK_FORTH | SURFACE_CONSTRAINT_TOL | ||
| SURFACE_LACE_CUT_DIR | SURFACE_SMOOTH_TOL | ||
| SURFACE_OUTPUT_PREF | SURFACE_ARC_FIT_TOL | ||
| SURFACE_CUT_OPT | SURFACE_SPLINE_TOL | ||
| SURFACE_OFFSET_SURFS | SURFACE_NORMAL_ANGLE | ||
| SURFACE_ONE_PASS | SURFACE_STEP_CUT_RATIO | ||
| SURFACE_CONSTRAIN | SURFACE_CORNER_RAD | ||
| SURFACE_RETRACT_OPT | SURFACE_MAX_CUT_ANGLE | ||
| SURFACE_STAY_IN_STOCK | CP1 | ||
| SURFACE_CLEAR_STOCK | CURVE_TOLERANCE | ||
| SURFACE_CLEAR_STOCK_TYPE | AUTO_ENTRY_CP | ||
| SURFACE_CUT_OVER_EDGES | AUTO_ENTRY_CLEAR_RAD | ||
| SURFACE_SKIP_FLATS | AUTO_EXIT_CP | ||
| SURFACE_CURVE_CUT_DIR | AUTO_EXIT_CLEAR_RAD | ||
| SFLOW_MACH_DIR | GEO_RAD | ||
| SFLOW_MACH_ZORDER | MIN_RAD | ||
| SFLOW_TRAVEL_AROUND_MODE | Z_STEP | ||
| SFLOCUT_TYPE | FM_CLEAR | ||
| INTERSECT_TYPE | FM_CUT_WIDTH | ||
| INTERSECT_CUTS_TYPE | CUT_ANGLE | ||
| INTERSECT_PASS_TYPE | STEPOVER_FEED | ||
| INTERSECT_CLEANUP_FROM | CLEAR_FEED | ||
| INTERSECT_PASSES_PER_SIDE | SCALLOP_FEED | ||
| LROUGH_ROUND_CORNERS | MIN_CUT | ||
| LROUGH_EXIT_PERP | PAST_STOCK | ||
| LROUGH_XPLUS | LTHREAD_Z_START | ||
| LROUGH_XMINUS | LTHREAD_Z_END | ||
| LROUGH_ZPLUS | LTHREAD_MAJOR_DIA | ||
| LROUGH_ZMINUS | LATHE_SURFACE_Z | ||
| LROUGH_AUTOFIN | LROUGH_MIN_RAD | ||
| LROUGH_SPINDLE_DIR | LROUGH_ENTRY_LINE | ||
| LROUGH_CONSTANT_PATH | LROUGH_ENTRY_RAD | ||
| LTHREAD_STYPE | LROUGH_EXIT_RAD | ||
| LTHREAD_ALTERNATE | LROUGH_EXIT_LINE | ||
| LTHREAD_NOM_PITCH_INDEX | LROUGH_START | ||
| WALL_STEP | LROUGH_CUT_WIDTH | ||
| WALL_TOP_TO_BOTTOM | LROUGH_RAMP_ANGLE | ||
| WALL_SAME_DIR | WALL_TOP | ||
| WALL_DCEP_SIDE | WALL_ANG | ||
| WALL_SWEPT_POCKET | WALL_BOT | ||
| WALL_SWEPT_ISLAND | WALL_ITOP | ||
| CUT_SIDE | WALL_IANG | ||
| S_USE_ADV_TOL | WALL_IBOT | ||
| M_USE_ADV_TOL | WALL_USER_STEP | ||
| WALL_MODE | WALL_SHAPE_STEP | ||
| INTER_OP_OVERRIDE | WALL_RIDGE_HEIGHT | ||
| UTIL_TYPE | DRILL_CLEAR_PLANE_LOC_CS | ||
| MD_FROM_TOOL | MSURF_CLEAR | ||
| MD_VARY_WITH_GEO | MSURF_STOCK_TOL | ||
| MD_VARY_WITH_FEAT | MFIXTURE_TOL | ||
| MD_RETRACT_LEVEL | M_ZSHIFT | ||
| CONTOUR_ENTRY_RAMP_TYPE | CONTOUR_ENTRY_RAMP_SLOPE | ||
| CONTOUR_ENTRY_HELIX_TYPE | CONTOUR_ENTRY_RAMP_START_Z | ||
| PREFER_SUBS | CONTOUR_ENTRY_RAMP_MAX_CUT | ||
| CONTOUR_ENTRY_RAMP_ANGLE | |||
| String Values | CONTOUR_ENTRY_HELIX_SLOPE | ||
| COMMENT | CONTOUR_ENTRY_HELIX_START_Z | ||
| OP_START | CONTOUR_ENTRY_HELIX_MAX_CUT | ||
| OP_END | CONTOUR_ENTRY_HELIX_DIA | ||
| DRILL_BORE_CUT_DIA | |||
| DRILL_BORE_CLEAR_DIA | |||
| DRILL_BORE_CLEAR_AMOUNT | |||
| DRILL_BORE_ENTRY_EXIT_RAD | |||
| DRILL_BORE_ENTRY_EXIT_LINE | |||
| DRILL_BORE_CUT_WIDTH | |||
| DRILL_BORE_STOCK | |||
| DRILL_BORE_OVERLAP | |||
| DRILL_BORE_APPROACH_ANGLE | |||
| DRILL_BORE_DESIRED_STEP |
| Floating Point Values | Description | Version Number |
| CP1 | CP1 value | |
| CLEAR_RAD | Clear radius | |
| AUTO_CLEAR_VAL | Auto clearance value | |
| GRAPHIC_PART_DIST_VAL | Graphic part distance | |
| SPLINE_MACHINING_TOLERANCE | Entry Line Approach (0 or 1) | 11, 3, 7 |
| PART_ROUGH_TOLERANCE | Part Rough Tolerance | 11, 3, 7 |
| PART_FINISH_TOLERANCE | Part Finish Tolerance | 11, 3, 7 |
| FIXTURE_TOLERANCE | Fixture Tolerance | 11, 3, 7 |
| FIXTURE_CLEARANCE | Fixture Clearance | 11, 3, 7 |
| String Values | ||
| PART_NAME | Part name | |
| PART_FILE | Part filename | |
| MDD_NAME | MDD name | |
| MDD_FILE | MDD filename | |
| COMMENT | Part comment | |
| ALLOY | Material alloy type | |
| FAMILY | Material family type | |
| HARDNESS | Material hardness | |
| Integer Values | ||
| TYPE | Part type (mill or lathe) | |
| UNITS | Part units (inch or metric) | |
| RADIUS | Part radius | |
| AUTO_CLEAR_ON | Is Auto Clearance enabled (1 = yes) | |
| TOOL_POS | Is Tool Position enabled (1 = yes) | |
| MACH_FLOWS | Number of Flows | |
| TG_COUNT | Number of Toolgroups | |
| WP_COUNT | Number of WorkPieces | |
| NUM_FLOWS | Number of flows | |
| NUM_TOOL_GROUPS | Number of ToolGroups | |
| GRAPHIC_PART_DIST_ON | Is graphic part distance checked (1 = yes) | |
| ENTRY_LINE_APPROACH | Entry Line Approach (0 or 1) | 11, 3, 7 |
| MILL_CRC_TYPE | Mill CRC Type (0, 1 or 2) | 11, 3, 7 |
| LATHE_CRC_TYPE | Lathe CRC Type (0, 1 or 2) | 11, 3, 7 |
| CRC_ENTRY_LINE_VALIDATION | CRC Entry Line Validation (0 or 1) | 11, 3, 7 |
| OMIT_SMALL_CHORD_ARCS | Omit Small Chord Arcs (0 or 1) | 11, 3, 7 |
| USE_GLOBAL_SETTINGS_FOR_SOLIDS | Use Global Settings For Solids (0 or 1) | 11, 3, 7 |
| Floating Point Values | Description | Version Number |
| TOOL_CHANGE_X | Toolchange position in X | |
| TOOL_CHANGE_Y | Toolchange position in Y | |
| STOCK_X1 | Stock X1 dimension | |
| STOCK_Y1 | Stock Y1 dimension | |
| STOCK_Z1 | Stock X1 dimension | |
| STOCK_X2 | Stock X2 dimension | |
| STOCK_Y2 | Stock Y2 dimension | |
| STOCK_Z2 | Stock Z2 dimension | |
| Integer Values | Description | Version Number |
| MILL_CRC_TYPE | Mill CRC Type (0, 1 or 2) | 11, 3, 7 |
| Floating Point Values | Description | Version Number |
| TOOL_CHANGE_X | Toolchange position in X | |
| TOOL_CHANGE_Z | Toolchange position in Z | |
| STOCK_RAD | Stock radius | |
| STOCK_Z1 | Stock Z1 dimension | |
| STOCK_Z2 | Stock Z2 dimension | |
| Integer Values | Description | Version Number |
| LATHE_CRC_TYPE | Lathe CRC Type (0, 1 or 2) | 11, 3, 7 |
| Integer Values | Description |
| SPINDLE_USED | Is this spindle used (1 = yes) |
| STOCK_Z1 | Stock Z1 value |
| STOCK_Z2 | Stock Z2 value |
| STOCK_RAD | Stock radius |
| STOCK_DIA | Stock diameter |
| CHUCK_WIDTH | Chuck width |
| CHUCK_PART_LEN | Chuck part length |
| CLEAR_Z | Clear position in Z |
| CLEAR_RAD | Clear radius |
| CLEAR_DIA | Clear diameter |
| Integer Values | Description |
| START_PROG_NUM | |
| SEQ_FROM | |
| SEQ_BY | |
| ABS_MOVES | |
| METRIC_OUTPUT | |
| COMMENTS | |
| OP_STOPS | |
| NUM_PARTS | |
| WORK_FIXTURES | |
| ONE_PART_ALL_TOOLS | |
| INTER_PART_FULL_UP | |
| MINIMIZE | |
| SELECTED_OPS | |
| PREF_SUB | |
| PREF_HEADER_PROG_NAME | |
| PREF_HEADER_PROG_COMMENT | |
| PREF_HEADER_FORMAT_NAME | |
| PREF_HEADER_FORMAT_CODE | |
| PREF_HEADER_DATE_TIME | |
| PREF_HEADER_ABS_INC | |
| PREF_HEADER_NUM_PARTS | |
| PREF_HEADER_START_TOOL | |
| PREF_HEADER_SPECIAL | |
| PREF_OP_OPNUM_TYPE | |
| PREF_OP_OP_COMMENT | |
| PREF_OP_WG_COMMENT | |
| PREF_OP_TOOLNUM_TYPE | |
| PREF_OP_TOOL_COMMENT | |
| PREF_FOOTER_CHARS | |
| PREF_FOOTER_FEET | |
| PREF_FOOTER_METERS | |
| PREF_FOOTER_METRES | |
| Floating Point Values | Description |
| PART_SPACING_X | |
| PART_SPACING_Y | |
| PART_SPACING_Z | |
| Floating String Values | |
| POST_FILE | |
| OUTPUT_FILE |
| Name | Description |
| AFR_SELECT_MODE | AFR selection mode |
| AFR_MATCH_MODE | AFR match mode |
| AFR_CS_MODE | AFR CS creation option |
| AFR_CS1_ORIGIN | AFR CS1 origin option |
| GROUP_MODE | Group mode |
| GROUP_SAME_TYPE | Group same hole type together |
| GROUP_SAME_CS | Group same CS together |
| GROUP_SAME_DIA | Group same diameter together |
| GROUP_KEEP | Keep in group |
| GROUP_SAME_TOP_Z | Group same top Z together |
| GROUP_SAME_BOTTOM_Z | Group same bottom Z together |
| GROUP_SAME_MID_Z | Group same mid Z together |
| Name | Description |
| AFR_CLEAR_PLANE_TOL | AFR clearance plane tolerance |
| GROUP_ANG_TOL | Angular tolerance value |
| GROUP_LIN_TOL | Linear tolerance value |
| PREFS_TOP_CLEAR | Preferences top clearance amount |
| PREFS_BLIND_BOTTOM_ADJUST | Preferences blind hole bottom adjustment value |
| PREFS_THRU_BOTTOM_ADJUST | Preferences through hole bottom adjustment value |
| PREFS_THRU_DRILL_TIP_ANGLE | Preferences through hole drill tip angle |
| Name | Description |
| AFR_WG_NAME | WorkGroup name |
| Floating Point Values | Description |
| TOOL_CHANGE_X | Toolchange position in X |
| TOOL_CHANGE_Y | Toolchange position in Y |
| TOOL_CHANGE_Z | Toolchange position in Z |
