Process Floating
From Macros Wiki
Jump to navigationJump to search
| Parameter | Description | Version Number |
|---|---|---|
| ENTRY_CLEAR | Entry clerance height | |
| EXIT_CLEAR | Exit clearance height | |
| ENTRY_LINE | Entry line length | |
| EXIT_LINE | Exit line length | |
| ENTRY_RAD | Entry radius | |
| EXIT_RAD | Exit radius | |
| ENTRY_FEED | Entry feedrate | |
| CONTOUR_FEED | Contour feedrate | |
| SURF_Z | Surface Z | |
| SURFACE_Z | Surface Z | |
| TIP_Z | Tip Z (depth) | |
| Z_STEP_WANTED | Z step desired | |
| CUT_WIDTH | Cut width | |
| STOCK | Stock amount | |
| BOSS_STOCK | Boss stock amount | |
| OVERHANG | Overhang amount | |
| OVERLAP | Overlap amount | |
| OPEN_CLEARANCE | Open clearance amount | |
| MTHREAD_START_THREAD | Thread Mill start | |
| MTHREAD_END_THREAD | Thread Mill end | |
| MTHREAD_CUT_DIA | Thread Mill cut diameter | |
| MTHREAD_CLEAR_DIA | Thread Mill clearance diameter | |
| MTHREAD_PITCH | Thread Mill pitch | |
| MTHREAD_FEED | Thread Mill feedrate | |
| SURFACE_EFEED | Surface entry feedrate | |
| SURFACE_CFEED | Surface contour feedrate | |
| SURFACE_STOCK | Surface stock amount | |
| SURFACE_FIXTURE_CLEAR | Surface fixture clearance | |
| SURFACE_STEPOVER | Surface stepover | |
| SURFACE_RIDGE_HEIGHT | Surface ridge height | |
| SURFACE_CUT_ANGLE | Surface cut angle | |
| SURFACE_DESIRED_Z | Surface desired Z step | |
| SURFACE_CONST_FACES_CLEAR | Surface constant faces clearance | |
| SURFACE_CUT_TOL | Surface cut tolerance | |
| SURFACE_STOCK_TOL | Surface stock tolerance | |
| SURFACE_FIXTURE_TOL | Surface fixture tolerance | |
| SURFACE_CONSTRAINT_TOL | Surface constraint tolerance | |
| SURFACE_SMOOTH_TOL | Surface smoothing tolerance | |
| SURFACE_ARC_FIT_TOL | Surface arc fit tolerance | |
| SURFACE_SPLINE_APPROX_TOL | Surface spline approximation tolerance | |
| SURFACE_NORMAL_ANGLE | Surface normal angle | |
| SURFACE_STEP_CUT_RATIO | Surface step cut ratio | |
| SURFACE_CORNER_RAD | Surface corner radius | |
| SURFACE_MAX_CUT_ANGLE | Surface maximum cut angle | |
| LROUGH_START_SIDE_EXT | Lathe rough side extension | |
| LROUGH_MIN_RAD | Lathe rough minimum radius | |
| LROUGH_STOCK | Lathe rough stock amount | |
| LROUGH_STOCK_X | Lathe rough stock in X | |
| LROUGH_STOCK_Z | Lathe rough stock in Z | |
| LROUGH_ENTRY_LINE | Lathe rough entry line length | |
| LROUGH_ENTRY_RAD | Lathe rough entry arc radius | |
| LROUGH_EXIT_RAD | Lathe rough exit arc radius | |
| LROUGH_EXIT_LINE | Lathe rough exit line length | |
| LROUGH_ROUGH_START | Lathe rough start amount | |
| LROUGH_MAX_RPM | Lathe rough maximum RPM | |
| LROUGH_SFPM | Lathe rough Surface Speed | |
| LROUGH_FEED | Lathe rough feedrate | |
| LROUGH_CLEARANCE | Lathe rough clearance amount | |
| LROUGH_ENTRY_FEED | Lathe rough entry feedrate | |
| LROUGH_CONTOUR_FEED | Lathe rough contour feedrate | |
| LROUGH_AUTO_FINISH_FEED | Lathe rough auto finish feedrate | |
| LROUGH_TURN_CUT_WIDTH | Lathe rough cut width | |
| LROUGH_RAMP_ANGLE | Lathe rough ramp angle | |
| LROUGH_PLUNGE_TYPE | Lathe rough plunge type | |
| LROUGH_PLUNGE_FIRST | Lathe rough first | |
| LROUGH_DIR_FWD | Lathe rough direction fwd | |
| LROUGH_BACK_AND_FORTH | Lathe rough back and forth | |
| LROUGH_PLUNGE_ANGLE | Lathe rough plunge angle | |
| LROUGH_CUT_WIDTH | Lathe rough cut width | |
| LROUGH_FEED_PERCENT | Lathe rough feed percentage | |
| LROUGH_PECK | Lathe rough peck value | |
| LROUGH_RETRACT | Lathe rough retract value | |
| LROUGH_CUT_X | Lathe rough cut in X | |
| LROUGH_CUT_Z | Lathe rough cut in Z | |
| LROUGH_SHIFT_CUT_WIDTH | Lathe rough shift cut width | |
| LROUGH_CYCLE_SP_X | Lathe rough cycle start point in X | |
| LROUGH_CYCLE_SP_Z | Lathe rough cycle start point in Z | |
| LROUGH_OFFSET_CUT_DEPTH | Lathe rough offset cycle cut depth | |
| LTHREAD_RPM | Lathe thread cycle spindle speed RPM | 11.0.4 |
| LTHREAD_Z_START | Lathe thread cycle Z start | |
| LTHREAD_Z_END | Lathe thread cycle Z end | |
| LTHREAD_NOMINAL | Lathe thread cycle nominal pitch | |
| LTHREAD_PITCH | Lathe thread cycle pitch | |
| LTHREAD_MAJOR_DIA | Lathe thread cycle major diameter | |
| LTHREAD_MINOR_DIA | Lathe thread cycle minor diameter | |
| LTHREAD_THREAD_HEIGHT | Lathe thread cycle height | |
| LTHREAD_TAPER | Lathe thread cycle taper amount | |
| LTHREAD_THREAD_ANGLE | Lathe thread cycle angle | |
| LTHREAD_CUT_DEPTH | Lathe thread cycle cut depth | |
| LTHREAD_LAST_CUT | Lathe thread cycle last cut | |
| LTHREAD_Z_START_EXTEND | Lathe thread cycle Z start extension | |
| LTHREAD_Z_END_EXTEND | Lathe thread cycle Z end extension | |
| LTHREAD_X_START_EXTEND | Lathe thread cycle X start extension | |
| LTHREAD_X_END_EXTEND | Lathe thread cycle X end extension | |
| LDRILL_DWELL | Lathe drill cycle dwell amount | |
| LDRILL_PECK | Lathe drill cycle peck value | |
| LDRILL_CLEARANCE | Lathe drill cycle clearance | |
| LDRILL_RETRACT | Lathe drill cycle retract value | |
| LDRILL_TAP_PERCENT | Lathe drill cycle tap percentage | |
| LDRILL_FEED | Lathe drill cycle feedrate | |
| LDRILL_TIP_Z | Lathe drill cycle tip Z (end position) | |
| LDRILL_SURFACE_Z | Lathe drill cycle surface Z (start position) | |
| TOOL_CHANGE | Tool change | |
| CP1 | CP1 value | |
| CURVE_TOL | Curve tolerance | |
| AUTO_ENTRY_CP | Auto entry CP | |
| AUTO_ENTRY_CLEAR_RAD | Auto entry clear radius | |
| AUTO_EXIT_CP | Auto exit CP | |
| AUTO_EXIT_CLEAR_RAD | Auto exit clear radius | |
| AXIS_INFO | Axis info | |
| GEO_RAD | Geometry radius | |
| MIN_RAD | Minimum radius | |
| Z_STEP | Actual Z step | |
| FM_CLEAR | Clearance | |
| FM_CUT_WIDTH | Cut width | |
| CUT_ANGLE | Cut angle | |
| STEPOVER_FEED | Stepover feed | |
| CLEAR_FEED | Clearance feed | |
| SCALLOP_FEED | Scallop feed | |
| MIN_CUT | Minimum cut | |
| RPM | Spindle speed | |
| RPMS | Spindle speed | |
| DRILL_FEED | Drill feedrate | |
| PAST_STOCK | Past stock amount | |
| POCKET_ENTRY_PLUNGE_PT_X | Plunge point in X | |
| POCKET_ENTRY_PLUNGE_PT_Y | Plunge point in Y | |
| POCKET_ENTRY_RAMP_SLOPE | Ramp slope | |
| POCKET_ENTRY_RAMP_START_Z | Ramp start in Z | |
| POCKET_ENTRY_RAMP_MAX_CUT | Ramp maximum cut | |
| POCKET_ENTRY_RAMP_WALL_CLEAR | Ramp wall clearance | |
| POCKET_ENTRY_RAMP_ANGLE | Ramp angle | |
| POCKET_ENTRY_HELIX_SLOPE | Entry helix slope | |
| POCKET_ENTRY_HELIX_ANGLE | Entry helix angle | |
| POCKET_ENTRY_HELIX_START_Z | Entry helix start in z | |
| POCKET_ENTRY_HELIX_MAX_CUT | Entry helix maximimum cut | |
| POCKET_ENTRY_HELIX_WALL_CLEAR | Entry helix wall clearance | |
| POCKET_ENTRY_HELIX_DIA | Entry helix diameter | |
| POCKET_ENTRY_HELIX_CP_X | Entry helix CP in X | |
| POCKET_ENTRY_HELIX_CP_X | Entry helix CP in Y | |
| POCKET_ENTRY_PERIPH_START_Z | Entry peripheral start in Z | |
| POCKET_ENTRY_PERIPH_SLOPE | Entry periphery slope | |
| SURFACE_ENTRY_PLUNGE_PT_X | Entry Plunge point in X | |
| SURFACE_ENTRY_PLUNGE_PT_Y | Entry Plunge point in Y | |
| RAPID_CLEARANCE | Rapid clearance amount | |
| CONTOUR_SURFACE_STOCK | Contour surface stock | 12.0.29 |
| POCKET_SURFACE_STOCK | Pocket surface stock | 12.0.29 |
| DRILL_DWELL | Drill cycle dwell amount | |
| DRILL_PECK_PERCENT | Peck depth as a percentage of tool diameter | 12.0.36 |
| DRILL_PECK_VALUE | Peck depth value | 12.0.36 |
| DRILL_PECK_CLEARANCE | Drill cycle peck clearance amount | |
| DRILL_TAP_PERCENT | Drill cycle tap percentage | |
| DRILL_BORE_PULLOFF | Drill cycle bore pulloff amount | |
| DRILL_PECK_RETRACT | Drill cycle peck retract amount | |
| WALL_TOP | Wall top | |
| WALL_ANGLE | Wall angle | |
| WALL_BOTTOM | Wall bottom | |
| WALLI_TOP | Wall (internal) top | |
| WALLI_ANGLE | Wall (internal) angle | |
| WALLI_BOTTOM | Wall (internal) bottom | |
| WALL_USER_STEP | Wall user step | |
| WALL_SHAPE_STEP | Wall shape step | |
| WALL_RIDGE_HEIGHT | Wall ridge height | |
| MSURF_CLEAR | Clearance amount | |
| MSURFACE_CLEAR | Clearance amount | |
| MSTOCK_TOL | Stock tolerance | |
| MFIX_TOL | Fixture tolerance | |
| MFIXTURE_TOL | Fixture tolerance | |
| MZSHIFT | Z shift amount | |
| CONTOUR_EXTRA_OFFSETS_VAL | Extra offsets values | 10.5.18 |
| CONTOUR_ENTRY_RAMP_SLOPE | Contour process entry ramp slope | |
| CONTOUR_ENTRY_RAMP_START_Z | Contour process entry ramp start in Z | |
| CONTOUR_ENTRY_RAMP_MAX_CUT | Contour process entry ramp maximum cut | |
| CONTOUR_ENTRY_RAMP_ANGLE | Contour process entry ramp angle | |
| CONTOUR_ENTRY_HELIX_SLOPE | Contour process entry helix slope | |
| CONTOUR_ENTRY_HELIX_START_Z | Contour process entry helix start in Z | |
| CONTOUR_ENTRY_HELIX_MAX_CUT | Contour process entry helix maximum cut | |
| CONTOUR_ENTRY_HELIX_DIA | Contour process entry helix diameter | |
| WRAP_START_ANGLE | Wrap start angle,same as option in Rotate tab | |
| WRAP_NUM_COPIES | Wrap number of duplications,same as option in Rotate tab | |
| WRAP_COPY_ANGLE | Wrap duplication angle,same as option in Rotate tab | |
| ADV_LINE_ENTRY_CRC | Advanced line entry CRC | |
| ADV_LINE_EXIT_CRC | Advanced line exit CRC | |
| ADV_ARC_ENTRY_CRC | Advanced arc entry CRC | |
| ADV_ARC_ENTRY_RAD | Advanced arc entry radius | |
| ADV_ARC_EXIT_CRC | Advanced arc exit CRC | |
| ADV_ARC_EXIT_RAD | Advanced arc exit radius | |
| DRILL_BORE_CUT_DIA | Drill bore cut diameter | |
| DRILL_BORE_CLEAR_DIA | Drill bore clear diameter | |
| DRILL_BORE_CLEAR_AMOUNT | Drill bore clear amount | |
| DRILL_BORE_ENTRY_EXIT_RAD | Drill bore entry exit radius | |
| DRILL_BORE_ENTRY_EXIT_LINE | Drill bore entry exit line length | |
| DRILL_BORE_CUT_WIDTH | Drill bore cut width | |
| DRILL_BORE_STOCK | Drill bore stock amount | |
| DRILL_BORE_OVERLAP | Drill bore overlap amount | |
| DRILL_BORE_APPROACH_ANGLE | Drill bore approach angle | |
| DRILL_BORE_DESIRED_STEP | Drill bore desired step amount | |
| ADV_LINE_ENTRY_OFF_PART_LINE | Line Entry Off Part Line value | 10.2.22 |
| ADV_LINE_ENTRY_OFF_PART_ANGLE | Line Entry Off Part Line angle | 10.2.22 |
| ADV_LINE_ENTRY_OFF_PART_DIST | Line Entry Off Part distance | 10.2.22 |
| ADV_LINE_ENTRY_RAMP_DIST | Line Entry Ramp distance | 10.2.22 |
| ADV_LINE_EXIT_OFF_PART_LINE | Line Exit Off Part Line value | 10.2.22 |
| ADV_LINE_EXIT_OFF_PART_ANGLE | Line Exit Off Part Line angle | 10.2.22 |
| ADV_LINE_EXIT_OFF_PART_DIST | Line Exit Off Part distance | 10.2.22 |
| ADV_LINE_EXIT_RAMP_DIST | Line Exit Ramp distance | 10.2.22 |
| ADV_ARC_ENTRY_OFF_PART_LINE | Arc Entry Off Part Line value | 10.2.22 |
| ADV_ARC_ENTRY_OFF_PART_DIST | Arc Entry Off Part distance | 10.2.22 |
| ADV_ARC_ENTRY_RAMP_DIST | Arc Entry Ramp distance | 10.2.22 |
| ADV_ARC_EXIT_OFF_PART_LINE | Arc Exit Off Part Line value | 10.2.22 |
| ADV_ARC_EXIT_OFF_PART_DIST | Arc Exit Off Part distance | 10.2.22 |
| ADV_ARC_EXIT_RAMP_DIST | Arc Exit Ramp distance | 10.2.22 |
| LROUGH_END_LIMIT_VAL | lathe Roughing End Limit Value | 10.2.22 |
| BAXIS_MIN_ANGLE_VAL | B Axis Turning, Minimum Angle | 10.2.22 |
| BAXIS_MAX_ANGLE_VAL | B Axis Turning, Maximum Angle | 10.2.22 |
| BAXIS_LEAD_LAG_ANGLE | B Axis Turning, Lead Lag Angle | 10.2.22 |
| BAXIS_COLLISION_CLEARANCE | B Axis Turning, Collision Check Clearance | 10.2.22 |
| THREAD_WHIRL_NUM_FLUTES | Number of Flutes | 10.2.22 |
| THREAD_WHIRL_FEED_PER_FLUTE | Feed Per Flute | 10.2.22 |
| THREAD_WHIRL_FEED | Feed | 10.2.22 |
| THREAD_WHIRL_PITCH | Pitch (mm) | 10.2.22 |
| THREAD_WHIRL_RPM | Spindle Speed | 10.2.22 |
| THREAD_WHIRL_CP2 | Entry Clear Z | 10.2.22 |
| THREAD_WHIRL_CP3 | Exit Clear Z | 10.2.22 |
| THREAD_WHIRL_IN_X | Run In X | 10.2.22 |
| THREAD_WHIRL_IN_Z | Run In Z | 10.2.22 |
| THREAD_WHIRL_OUT_X | Run Out X | 10.2.22 |
| THREAD_WHIRL_OUT_Z | Run Out Z | 10.2.22 |
| THREAD_WHIRL_START_X | Start X | 10.2.22 |
| THREAD_WHIRL_START_Z | Start Z | 10.2.22 |
| THREAD_WHIRL_END_X | End X | 10.2.22 |
| THREAD_WHIRL_END_Z | End Z | 10.2.22 |
| THREAD_WHIRL_APP_X | Approach X | 10.2.22 |
| THREAD_WHIRL_APP_Z | Approach Z | 10.2.22 |
| THREAD_WHIRL_RET_X | Retract X | 10.2.22 |
| THREAD_WHIRL_RET_Z | Retract Z | 10.2.22 |
| THREAD_WHIRL_COOLANT | Coolant Type | 10.2.22 |
| THREAD_WHIRL_CONST_FEED_ON | 1=Constant Feed On | 10.2.22 |
| THREAD_WHIRL_CONST_FEED_VAL | Constant Feed value | 10.2.22 |
| THREAD_WHIRL_C_OFFSET | Type of C Offset | 10.2.22 |
| THREAD_WHIRL_START_C_OFFSET | C Offset Start | 10.2.22 |
| THREAD_WHIRL_END_C_OFFSET | C Offset End | 10.2.22 |
| THREAD_MILL_PLUNGE_DIA | Plunge diameter | 10.3.11 |
| THREAD_MILL_ENTRY_FEED | Entry feedrate | 10.3.11 |
| THREAD_MILL_CRC_LINE | CRC line length | 10.3.11 |
| THREAD_MILL_ENTRY_ANGLE | Entry angle | 10.3.11 |
| THREAD_MILL_EXIT_ANGLE | Exit angle | 10.3.11 |
| THREAD_MILL_ENTRY_EXIT_RAD | Entry/Exit radius | 10.3.11 |
| THREAD_MILL_THREAD_HEIGHT | Thread height | 10.3.11 |
| THREAD_MILL_CUT_DEPTH | Depth of first cut | 10.3.11 |
| THREAD_MILL_LAST_CUT_AMOUNT | Last cut amount | 10.3.11 |
| THREAD_MILL_TAPER_ANGLE | Taper angle | 10.3.11 |
| THREAD_MILL_ADJUST_DEPTH_DELTA | Amount to adjust end depth | 10.3.11 |
| THREAD_MILL_START_DEPTH | Start depth Z | 10.3.11 |
| THREAD_MILL_END_DEPTH | End depth Z | 10.3.11 |
| MULTI_SHAPE_OPEN_END_EXTENSION | End extension value | 25.0.25 |
| MCUTOFF_DEPTH_OF_CUT | depth position based on part origin to use for cutoff | 12.0.28 |
| MCUTOFF_POSITION_OF_CUT | Cut off position based on part origin specified on cutoff part side | 25.0.25 |
| MCUTOFF_START_POSITION | start position of the tool before the cut along the cut direction | 25.0.25 |
| MCUTOFF_END_POSITION | end position of the tool after the cut along the cut direction | 25.0.25 |
| MCUTOFF_TWOCUT_OVERLAP | depth position beyond the origin the tool will use for each pass | 25.0.25 |
| MCUTOFF_SPIRAL_CENTER_PT_X | X center point of spiral | 25.0.25 |
| MCUTOFF_SPIRAL_CENTER_PT_Y | Y center point of spiral | 25.0.25 |
| MCUTOFF_SPIRAL_RAD | material radius for the | 25.0.25 |
| MCUTOFF_SPIRAL_MAX_CUT | maximum cut depth the tool will take | 25.0.25 |
| MCUTOFF_SPIRAL_OVERCUT_DEPTH | material diameter for the cut, the spiral will cut from the surface to the center | 25.0.25 |
