Process Integer
From Macros Wiki
Jump to navigationJump to search
| Parameter | Description | Version Number |
|---|---|---|
| TYPE | Process type | |
| MILL_TYPE | Mill process type | |
| LATHE_TYPE | Lathe process type | |
| ALLOW_TOOL | 1=Allow, 0=No Tool | 10.9.13 |
| TOOL_NUM | Tool number | |
| CRC | CRC state | |
| COOLANT | Coolant type | |
| CUT_TYPE | Cut type | |
| REPEATS | Number of repeats | |
| MTHREAD_TRAVERSE_CP1 | Thread Mill traverse CP1 | |
| MTHREAD_ID_OD | thread Mill ID or OD | |
| MTHREAD_THREAD_DIR | Thread Mill direction | |
| MTHREAD_RAPID_IN | Thread Mill rapid in | |
| SURFACE_TYPE | Surface process type | |
| SURFACE_CUT_TYPE | Cut type | |
| SURFACE_BACK_AND_FORTH | Back and Forth setting | |
| SURFACE_LACE_CUT_DIR | Lace cut direction | |
| SURFACE_OUTPUT_PREF | Output preference | |
| SURFACE_CUT_OPT | Cut option | |
| SURFACE_OFFSET_SURFACES | Offset surfaces | |
| SURFACE_ONE_PASS | One pass | |
| SURFACE_CONSTRAIN | Contrain state | |
| SURFACE_RETRACT_OPTION | Retract option | |
| SURFACE_STAY_IN_STOCK | Stay in stock | |
| SURFACE_CLEAR_STOCK | Clear stock | |
| SURFACE_CLEAR_STOCK_TYPE | Stock type | |
| SURFACE_CUT_OVER_EDGES | Cut over edges | |
| SURFACE_SKIP_FLATS | Skip flats | |
| CURVE_CUT_DIR | Cut direction | |
| SURFACE_FLOW_MACH_DIR | machining direction | |
| SURFACE_FLOW_MACH_Z_ORDER | Z order | |
| SURFACE_FLOW_TRAVEL_AROUND_MODE | Travel around mode | |
| SURFACE_FLOW_CUT_TYPE | Cut type | |
| SURFACE_INTERSECT_TYPE | Intersection type | |
| SURFACE_CUTS_TYPE | Cut type | |
| SURFACE_PASSES_TYPE | Passes type | |
| SURFACE_CLEANUP_TYPE | Cleanup type | |
| SURFACE_PASSES_PER_SIDE | Number of passes per side | |
| LATHE_PREFER_CANNED | Prefer canned option | |
| LATHE_CLEAR_ID | Clearance ID | |
| LROUGH_ROUND_CORNERS | Round corners | |
| LROUGH_CUT_OFF | Cut off | |
| LROUGH_CUT_DIR | Cut direction | |
| LROUGH_ENTRY_PERP | Entry perpendicular | |
| LROUGH_EXIT_PERP | Exit perpendicular | |
| LROUGH_ROUGH_TYPE | Rough cycle type | |
| LROUGH_CSS | Constant surface speed | |
| LROUGH_RAPID_STEP | Rapid step | |
| LROUGH_MONOTONIC | Is cycle path monotonic | |
| LROUGH_AVOID_AIR | Avoid air | |
| LROUGH_XPLUS | Cut in X plus direction | |
| LROUGH_XMINUS | Cut in X minus direction | |
| LROUGH_ZPLUS | Cut in Z plus direction | |
| LROUGH_ZMINUS | Cut in Z minus direction | |
| LROUGH_AUTO_FINISH | Auto finish option | |
| LROUGH_SPINDLE_DIR | Spindle direction | |
| LROUGH_FINISH_LAST | Finish last cut | |
| LROUGH_CENTER_OUT | Cut from center outwards | |
| LROUGH_CONSTANT_STEP | Constant step | |
| LROUGH_PECK | Peck value | |
| LROUGH_PLUNGE_TYPE | Plunge type | |
| LROUGH_CONSTANT_PATH | Constant path | |
| LROUGH_FIXED_SP | Fixed start point | |
| LROUGH_NUM_PASSES | Number of passes | |
| LROUGH_SHIFT_SQUARE_CORNERS | Shift square corners | |
| LROUGH_CLEANUP_PASS | Use a cleanup pass | |
| LROUGH_USE_DEFLECT_COMP | Use deflect compensation | |
| LROUGH_DEFLECT_COMP_VAL | Deflect compensation value | |
| LROUGH_MULTI_PASS | Multi pass | |
| LATHE_CUT_OTHER_SIDE | Can cut other side | |
| LATHE_USE_AUTO_CLEAR | Use auto clearance | |
| LTHREAD_SHAPE_METHOD | 0=From Parameters, 1=From Shape | 12.0.36 |
| LTHREAD_STYLE | Threading style | |
| LTHREAD_CUT_DIR | Cut direction | |
| LTHREAD_CUT_TYPE | Cut type | |
| LTHREAD_CSS | Constant Surface Speed | |
| LTHREAD_BALANCED_IN_FEED | Balanced in-feed | |
| LTHREAD_ALTERNATE | Alternate cuts | |
| LTHREAD_LAST_CUT | Last cut | |
| LTHREAD_NOMINAL_PITCH_INDEX | Nominal pitch index | |
| LTHREAD_TAPER_INDEX | Taper index | |
| LTHREAD_NUM_SPRING_PASSES | Number of spring passes | |
| LTHREAD_NUM_STARTS | Number of thread starts | |
| LDRILL_ENTRY | Lathe drill entry | |
| FEED_CONNECT | Use feed connect | |
| CRC_OFFSET | CRC offset number | |
| LEN_OFFSET | Length offset number | |
| CUSTOM_CBSET | Custom CBSET | |
| PATTERN_ON | Use a pattern | |
| PATTERN_INDEX | Pattern index | |
| ROUND_CORNERS | Round corners option | |
| ENTRY_PERP | Entry perpendicular | |
| EXIT_PERP | Exit perpendicular | |
| IGNORE_TOOLS | Ignore tools | |
| DEPTH_FIRST | Cut depth first | |
| SPRING_PASSES | Number of spring passes | |
| FM_USE_SHAPE | Use shape | |
| FM_HPLUS | H Plus value | |
| FM_VPLUS | V Plus value | |
| FM_MOVEH | Move Horizontal | |
| FM_BEFORE_ZIGZAG | Before ZigZag | |
| FM_BACK_AND_FORTH | Back and Forth | |
| FM_TYPE | FM type | |
| ENTRY_TYPE | Entry type | |
| START_ON_RIGHT | Start on the right | |
| RETRACTS | Use retracts | |
| HIT_PARALLEL | Hit parallel | |
| STAY_CLEAR | Stay clear | |
| CUT_BACK | Cut back | |
| SAME_STROKE | Same stroke | |
| FULL_DIA | Full diameter | |
| STEPOVER_FEED_LOCK | Stepover feed lock | |
| CLEAR_FEED_LOCK | Clear feed lock | |
| SCALLOP_FEED_LOCK | Scallop feed lock | |
| CLEAR_PERIPH | Clear periphery | |
| CS_NUM | CS number or process | |
| PATH_CS | CS number of toolpath | |
| POCKET_TYPE |
| |
| MILL_STAY_IN_STOCK | For checkbox "Use Stock" | |
| OFFSET_TRIM_OPTION | Offset trim options in roughing:
| |
| WALL_MODE | Wall mode | |
| PREFER_SUBS | Prefer subs option | |
| HIT_FLATS | Hit flats option | |
| POCKET_ENTRY_RAMP_TYPE | Ramp type | |
| POCKET_ENTRY_HELIX_TYPE | Helix type | |
| SURFACE_ENTRY_TYPE | Entry type | |
| SURFACE_ENTRY_RAMP_TYPE | Ramp type | |
| PROG_STOP | Program stop | |
| RAPID_IN | Rapid in | |
| MATERIAL_ONLY | material only cutting | |
| DRILL_TYPE | Drill type:
| |
| DRILL_POS_APPROACH | Drill position approach | |
| DRILL_CLEAR_PLANE | Drill clearance plane | |
| WALL_STEP | Wall step | |
| WALL_TOP_TO_BOTTOM | Top to Bottom | |
| WALL_SAME_DIR | Same direction | |
| WALL_SAME_DCEP_SIDE | Dcep side | |
| WALL_SWEPT_POCKET | Swept pocket | |
| WALL_SWEPT_ISLAND | Swept island | |
| S_USE_ADV_TOL | Use advance tolerance | |
| M_USE_ADV_TOL | Use advance tolerance | |
| CUT_SIDE | Cut side | |
| MD_FROM_TOOL | Modify depth from tool | |
| MD_VARY_WITH_GEO | Vary with geometry | |
| MD_VARY_WITH_FEAT | Vary with feature | |
| MD_RETRACT_LEVEL | Retract level | |
| MD_PROCESS_LOAD_H1Z_FEAT | Load H1 Feature Z | |
| CONTOUR_ENTRY_RAMP_TYPE | Ramp type | |
| CONTOUR_ENTRY_HELIX_TYPE | Helix type | |
| CONTOUR_RAMP_DOWN | 1=Ramp Down | 10.5.18 |
| CONTOUR_NUM_EXTRA_OFFSETS | Number of extra offsets | 10.5.18 |
| POCKET_OUTER_AS_BOSS | 1=Outer as Boss | 10.5.18 |
| WRAP | Wrap toolpath,same as option in Rotate tab
| |
| WRAP_NUM_COPIES | number of copies, same as option in Rotate tab | |
| DRILL_BORE_CUT_TYPE | Cut type | |
| ADV_EXIT_SAME_AS_ENTRY | 1=Exit values are same as entry | 10.2.22 |
| ADV_ENTRY_TYPE | Entry type | 10.2.22 |
| ADV_EXIT_TYPE | Exit type | 10.2.22 |
| ADV_LINE_ENTRY_USE_CRC | 1=Line Entry uses CRC | 10.2.22 |
| ADV_LINE_ENTRY_USE_OFF_PART_LINE | 1=Line Entry uses Off Part Line | 10.2.22 |
| ADV_LINE_ENTRY_USE_RAMP | 1=Line Entry uses Ramp | 10.2.22 |
| ADV_LINE_ENTRY_RAMP_INCLUDE_LINE | 1=Line Entry Ramp uses Include Line | 10.2.22 |
| ADV_LINE_EXIT_USE_CRC | 1=Line Exit uses CRC | 10.2.22 |
| ADV_LINE_EXIT_USE_OFF_PART_LINE | 1=Line Exit uses Off Part Line | 10.2.22 |
| ADV_LINE_EXIT_USE_RAMP | 1=Line Exit uses Ramp | 10.2.22 |
| ADV_LINE_EXIT_RAMP_INCLUDE_LINE | 1=Line Exit Ramp uses Include Line | 10.2.22 |
| ADV_ARC_ENTRY_USE_CRC | 1=Arc Entry uses CRC | 10.2.22 |
| ADV_ARC_ENTRY_USE_OFF_PART_LINE | 1=Arc Entry uses Off Part Line | 10.2.22 |
| ADV_ARC_ENTRY_USE_RAMP | 1=Arc Entry uses Ramp | 10.2.22 |
| ADV_ARC_ENTRY_RAMP_INCLUDE_RADIUS | 1=Arc Entry Ramp uses Include Radius | 10.2.22 |
| ADV_ARC_EXIT_USE_CRC | 1=Arc Exit uses CRC | 10.2.22 |
| ADV_ARC_EXIT_USE_OFF_PART_LINE | 1=Arc Exit uses Off Part Line | 10.2.22 |
| ADV_ARC_EXIT_USE_RAMP | 1=Arc Exit uses Ramp | 10.2.22 |
| ADV_ARC_EXIT_RAMP_INCLUDE_RADIUS | 1=Arc Exit Ramp uses Include Radius | 10.2.22 |
| PROC_ID | Process ID Number | 10.2.22 |
| LROUGH_USE_END_LIMIT | lathe Rough uses End Limit | 10.2.22 |
| DRILL_REVERSE_ORDER | Drill cycle has Reverse Order checked | 10.2.22 |
| BAXIS_USED | B Axis Turning is used | 10.2.22 |
| BAXIS_METHOD | B Axis Turning Method | 10.2.22 |
| BAXIS_MULTI_TRANS | B Axis Turning uses multiple transitions | 10.2.22 |
| BAXIS_USE_MIN_ANGLE | B Axis Turning Minimum Angle | 10.2.22 |
| BAXIS_USE_MAX_ANGLE | B Axis Turning Maximum Angle | 10.2.22 |
| BAXIS_SMOOTH_CORNERS | B Axis Turning uses Smooth Corners option | 10.2.22 |
| BAXIS_VECTOR_TYPE | B Axis Turning Vector Type | 10.2.22 |
| BAXIS_CHECK_COLLISIONS | B Axis Turning uses Collision Checking | 10.2.22 |
| UTIL_TYPE | Utility Process Type | 10.2.22 |
| THREAD_MILL_RAPID_TO_FROM_CLEAR | 1=Rapid to/from Clearance Diameter | 10.3.11 |
| THREAD_MILL_PLUNGE_AT_CENTER | 0=Plunge at center, 1=Plunge at Diameter | 10.3.11 |
| THREAD_MILL_VARY_WITH_GEO | 1=Vary depth with geometry | 10.3.11 |
| THREAD_MILL_ENTRY_EXIT_METHOD | Entry/Exit method | 10.3.11 |
| THREAD_MILL_ENTRY_EXIT_RAD | Entry/Exit radius | 10.3.11 |
| THREAD_MILL_CUT_TYPE | 0=One Top Pass, 1=One Finish Pass, 3=Const Cut 3=Const Load | 10.3.11 |
| THREAD_MILL_DO_LAST_CUT | 1=Specify exact depth of last cut | 10.3.11 |
| THREAD_MILL_NUM_SPRING_PASSES | Number of Spring Passes | 10.3.11 |
| THREAD_MILL_START_DEPTH_TYPE | 0=Abs Z, 1=Top of Hole, 2=Seg Start, 3=Seg End | 10.3.11 |
| THREAD_MILL_END_DEPTH_TYPE | 0=Top, 1=Chamfer, 2=Mid, 3=Bottom, 4=Seg start, 5=Seg end, 6=Abs | 10.3.11 |
| THREAD_MILL_START_SEGNUM | Start Depth Segment Number | 10.3.11 |
| THREAD_MILL_END_SEGNUM | End Depth Segment Number | 10.3.11 |
| THREAD_MILL_SEGMENT_MATCH | 1=Use Segment Matching | 10.3.11 |
| THREAD_MILL_SEG_MATCH_LEN | 1=Match Segment Length | 10.3.11 |
| THREAD_MILL_SEG_MATCH_DIA | 1=Match Segment Diameter | 10.3.11 |
| THREAD_MILL_SEG_MATCH_TAPER | 1=Match Segment Taper | 10.3.11 |
| THREAD_MILL_SEG_MATCH_METHOD | 1=Match Segment Method | 10.3.11 |
| THREAD_MILL_DIM_FROM_TOOL | 0=Dimension from Hole, 1=Dimension from Tool | 10.3.11 |
| THREAD_MILL_BOTTOM_UP | 0=Top down, 1=Bottom Up | 10.3.11 |
| MULTI_SHAPE_SINGLE_SHAPE_USE_MARKERS | 1=Use Markers, 0=Do not use markers | 12.0.28 |
| MULTI_SHAPE_CENTERLINE | 1=Use Markers, 0=Do not use markers | 12.0.28 |
| MULTI_SHAPE_CLOSED_INSIDE | 1=Tool inside, 0=Tool outside | 12.0.28 |
| MULTI_SHAPE_CLOSED_ALTERNATE_SIDES | 1 = Alternate tool side for nested shapes | 12.0.28 |
| MULTI_SHAPE_OPEN_START_EXTENSION | start extension | |
| MULTI_SHAPE_OPEN_END_EXTENSION | end extension | |
| COMMENT_LEN | Process comment length | 14.0.33 |
| LATHE_OD_ID_FACE | Lathe Approach Type: 0=OD, 1=ID Front, 2=ID Rear (if applicable), 3=Rear Face (if applicable) | -- |
| MCUTOFF_STYLE | Mill Cutoff style (saw or end mill) | 25.0.25 |
| MCUTOFF_STRATEGY | Cutting Strategy (sprial, single cut, two cuts same dir, two cuts back and forth) | 25.0.25 |
| MCUTOFF_PASS_DIR | Cur Direction (X or Y) only applicable to Saw Style and not spiral cutting stragegy | 25.0.25 |
| MCUTOFF_SPIRAL_DIR | spiral direction (CW or CCW) | 25.0.25 |
| MCUTOFF_RETRACT_TO_SURFACE_RAD | Retract to surface radius (only valid for sprial) | 25.0.25 |
| MCUTOFF_USE_ROTARY | use rotary or use position (like the rotate tab) | 25.0.25 |
