Process proc add

Up

}

Parameter	Type	Description	Version Number
Additive Processes
ADD_PROC_TYPE	Integer	Additive Process Type	14.0.20
ADD_NUM_LAYERS	Integer	Number of Cladding Layers	14.0.20
ADD_NUM_PASSES	Integer	Number of Heater/Dryer Passes	14.0.20
Additive Contour Process
ADD_MIN_WIDTH	Decimal	Minimum Contour Width	14.0.20
ADD_TILT_TYPE	Integer	Tilt Type	14.0.20
ADD_NUM_TRACKS	Integer	Number of Tilt Tracks	14.0.20
ADD_TILT_ANGLE_1	Decimal	Tilt Angle, Track 1	14.0.20
ADD_TILT_ANGLE_2	Decimal	Tilt Angle, Track 2	14.0.20
ADD_FAN_DIST_PER_STEP	Decimal	Tilt, Distance Per Step	14.0.20
ADD_FAN_DEG_PER_STEP	Decimal	Tilt, Degrees per Step	14.0.20
Closed Shapes Options
ADD_CONTOUR_CLOSED_REV_ALT_LAYERS	Integer	1 = Reverse Alternate Layers	14.0.20
ADD_CONTOUR_CLOSED_RAMP_OPTION	Integer	1 = Spiral Ramp On	14.0.20
ADD_CONTOUR_CLOSED_START_OPTION	Integer	Adjust Start Position Option	14.0.20
ADD_CONTOUR_CLOSED_RESET_AFTER_NUM	Integer	1 = Reset Start Number of Layers	14.0.20
ADD_CONTOUR_CLOSED_RESET_NUM_LAYERS	Integer	Number of Layers to Reset After	14.0.20
ADD_CONTOUR_CLOSED_ALL_WIDTH_SAME	Integer	1 = All Width Tracks, Same Start	14.0.20
ADD_CONTOUR_CLOSED_START_PERCENT	Decimal	Adjust Start Percentage	14.0.20
ADD_CONTOUR_CLOSED_START_DIST	Decimal	Adjust Start Distance	14.0.20
ADD_CONTOUR_CLOSED_MIN_CORNER_DIST	Decimal	Min Distance from a Corner	14.0.20
Additive Fill and Surfaces
ADD_LAYER_MOD_TYPE	Integer	1=Shift Layers, 2=Rotate Layers	14.0.20
ADD_LAYER_MOD_STEPS	Integer	Number of Layers per Group	14.0.20
ADD_LAYER_SHIFT_DISTANCE	Decimal	Shift Distance, Per layer	14.0.20
ADD_LAYER_ROTATE_ANGLE	Decimal	Rotation Angle, Per Layer	14.0.20
ADD_FILL_TYPE	Integer	Fill Pattern	14.0.20
ADD_FILL_CORNER	Integer	Fill Start Corner	14.0.20
ADD_FILL_SIDE	Integer	Fill Start Side	14.0.20
ADD_FILL_SPIRAL	Integer	1=Fill Spiral	14.0.20
ADD_FILL_DIR_CCW	Integer	1 = Fill CCW	14.0.20
ADD_FILL_OUTSIDE_IN	Integer	1 = Fill Outside In	14.0.20
ADD_FILL_NUM_SECTIONS	Integer	Fill, Number of Sections	14.0.20
ADD_FILL_CONNECT	Integer	Fill Connection Move Type	14.0.20
ADD_SOLIDS_FILL_TYPE	Integer	Fill Solids Option	14.0.20
Additive Rotary Surface Process
ADD_SURF_TYPE	Integer	Rotary Surface Type	14.0.20
ADD_SURF_START_Z_TYPE	Decimal	Start Z position	14.0.20
ADD_SURF_DIR_CW	Integer	1 = Direction CW	14.0.20
ADD_SURF_CIRCLE_ANGLE_TYPE	Integer		14.0.20
ADD_SURF_ROT_START_Z	Decimal		14.0.20
ADD_SURF_ROT_END_Z	Decimal		14.0.20
ADD_SURF_ROT_START_ANGLE	Decimal		14.0.20
ADD_SURF_ROT_CIRCLE_ANGLE	Decimal		14.0.20
ADD_CLEAR_Z	Decimal		14.0.20
Repeat Process
ADD_REPEAT_NUM_SECTIONS	Integer	Number of sections	14.0.20
ADD_REPEAT_ADJUST_CPS	Integer	1=Adjust Clearance Planes	14.0.20
Hybrid Process
ADD_HYBRID_CP2	Decimal	Entry Clearance Plane Height	14.0.20
ADD_HYBRID_CP3	Decimal	Exit Clearance Plane Height	14.0.20
ADD_HYBRID_BOTTOM_Z	Decimal	Z Start Height	14.0.20
ADD_HYBRID_TOP_Z	Decimal	Desired Z Top Height	14.0.20
ADD_HYBRID_ADJUST_CPS	Decimal	1 = Adjust Clearance Planes	14.0.20
ADD_HYBRID_NUM_LAYERS	Integer	Number of sections	14.0.20
ADD_HYBRID_NUM_SECTIONS	Integer	Number of sections	14.0.20
ADD_HYBRID_SUB_BOTTOM_Z	Decimal	1 = Subtractive Op at Bottom	14.0.20
ADD_HYBRID_SUB_TOP_Z	Decimal	1 = Subtractive Op at Top	14.0.20
ADD_HYBRID_SUB_CLEAR_Z	Decimal	Extra Clearance, Subtract Section	14.0.20
ADD_HYBRID_SUB_DEPTH_Z	Decimal	Amount to remove, Additive Section	14.0.20
Technology Data
ADD_USE_BASE_LAYER	Integer	1=Use Base Layer	14.0.20
ADD_USE_GRAD_LAYER	Integer	1=Use Gradient Material	14.0.20
ADD_NUM_GRAD_LAYERS_1	Integer	Number of Layers, Grad Material 1	14.0.20
ADD_NUM_GRAD_LAYERS_2	Integer	Number of Layers, Grad Material 2	14.0.20
ADD_BASE_MATERIAL_NAME	String	Base Material Name	14.0.20
ADD_CLAD_MATERIAL_NAME	String	cladding Material Name	14.0.20
ADD_GRAD_MATERIAL_NAME	String	Gradient Material Name	14.0.20