Operation Integer
From Macros Wiki
Jump to navigationJump to search
| Parameter | Description | Version Number |
|---|---|---|
| TOOL_NUM | Tool number | |
| PROC_GROUP | Process group number | |
| PROC_ID | Process ID number | |
| PROC_OP | Process operation number | |
| WG_NUM | WorkGroup number | |
| CS_NUM | CS number | |
| PATH_CS | Toolpath CS number | |
| LOCKS | Locks setting | |
| TYPE | Operation type | |
| MILL_TYPE | Mill operation type | |
| LATHE_TYPE | Lathe Operation type | |
| NUM_REPEATS | Number of repeats | |
| CRC | CRC on/off | |
| CRC_OFFSET | CRC offset number | |
| LEN_OFFSET | Length offset number | |
| COOLANT | Coolant type | |
| CUT_TYPE | Cut type | |
| CRC_SIDE | CRC side | |
| DRILL_TYPE | Drill cycle type | |
| DRILL_CLEAR_PLANE | Drill clearance plane height | |
| DRILL_POS_APPROACH | Use positive approach | |
| MATERIAL_ONLY | Use material only option | |
| RAPID_IN | Rapid in | |
| LTHREAD_TYPE | Lathe thread type | |
| LTHREAD_SHAPE_METHOD | 0=From Parameters, 1=From Shape | 12.0.36 |
| LTHREAD_STYPE | Lathe thread type | |
| LTHREAD_ALTERNATE | Lathe thread alternate cut option | |
| LTHREAD_NOM_PITCH_INDEX | Lathe thread nominal pitch index | |
| LTHREAD_BALANCED | Lathe thread balance option | |
| LTHREAD_ANGLE_ALT | Lathe thread alternate angle | |
| LTHREAD_STARTS | Lathe thread number of starts | |
| LTHREAD_LAST_CUT | Lathe thread last cut option | |
| LATHE_PREFER_CANNED | Prefer canned option | |
| LATHE_CANNED_AUTOFIN | Auto finish option | |
| LATHE_CUT_DIR | Cut direction | |
| NUM_SPRING_PASSES | Number of spring passes | |
| LATHE_ROUGH_TYPE | Rough cycle type | |
| LATHE_PULL_OFF_WALL | Pulloff wall value | |
| LATHE_PLUNGE_CUT_TYPE | Plunge cut type | |
| LATHE_PLUNGE_CENTER_OUT | Plunge from center outwards | |
| LATHE_PLUNGE_TYPE | Plunge type | |
| LATHE_PLUNGE_ENTRY_TYPE | Plunge entry type | |
| LATHE_PAT_SHIFT_FIXED_SRT | Pattern shift fixed option | |
| LATHE_PAT_SHIFT_PASSES | Pattern shift number of passes | |
| LATHE_SQUARE_CORNERS | Square corners option | |
| LATHE_NO_DRAG | No drag option | |
| LATHE_CUT_OFF | Cut off value | |
| LATHE_OD_ID_FACE | OD ID Face setting (OD=0, ID=1, Front Face=3, Back Face [MTM]=4) | |
| WRAP | Wrap toolpath,same as option in Rotate tab
| |
| WRAP_DUPS | number of copies, same as option in Rotate tab | |
| PROG_STOP | Program stop option | |
| POCKET_TYPE | Pocket type | |
| TOOL_GROUP | ToolGroup number | |
| USE_CSS | 1=CSS, 0=RPM | 12.8.30 |
| WORKPIECE | Workpiece number | |
| FLOW | Flow number | |
| SPIN_CONTROL | Spindle control option | |
| LATHE_CUT_OTHER_SIDE | Cut other side option | |
| POCKET_OUTER_AS_BOSS | 1=Outer as Boss | 10.5.18 |
| POCKET_ENTRY_RAMP | Pocket entry uses ramp | |
| POCKET_ENTRY_HELIX_TYPE | Pocket entry helix type | |
| SURFACE_ENTRY_TYPE | Surface entry type | |
| SURFACE_ENTRY_RAMP_TYPE | Surface entry ramp type | |
| MACH_ENGINE | Machining engine | |
| CRC_OFFSET | CRC offset number | |
| PATTERN_ON | Pattern on setting | |
| PATTERN_INDEX | Pattern index | |
| ROUND_CORNERS | Round corners option | |
| ENTRY_PERP | Entry is perpendicular | |
| EXIT_PERP | Exit is perpendicular | |
| IGNORE_TOOLS | Ignore tools option | |
| DEPTH_FIRST | Cut depth first | |
| FM_USE_SHAPE | Use shape | |
| FM_HPLUS | Cut in Horizontal plus direction | |
| FM_VPLUS | Cut in vertical plus direction | |
| FM_MOVEH | Move horizontal | |
| ZIG_ZAG | Zigzag option | |
| BACK_FORTH | Back and Forth is checked | |
| FM_TYPE | Type | |
| ENTRY_TYPE | Entry move type | |
| START_ON_RIGHT | Start on right | |
| RETRACTS | Use retracts | |
| HIT_PARALLEL | Hit parallel option | |
| STAY_CLEAR | Stay clear option | |
| CUT_BACK | Cut back amount | |
| SAME_STROKE | Same stroke option | |
| FULL_DIA | Full diameter value | |
| STEPOVER_FEED_LOCK | Stepover feed lock | |
| CLEAR_FEED_LOCK | Clearance feed lock is checked | |
| SCALLOP_FEED_LOCK | Scallop feed lock | |
| CLEAR_PERIPH | Clear periphery is selected | |
| HIT_FLATS | Hit flats option | |
| MTHREAD_TRAVERSE_CP1 | Thread mill traverse at CP1 | |
| MTHREAD_ID_OD | Thread mill ID or OD option | |
| MTHREAD_THREAD_DIR | Thread mill thread direction | |
| SURFACE_TYPE | Surface type | |
| SURFACE_CUT_TYPE | Surface cut type | |
| SURFACE_BACK_FORTH | Surface back and forth option | |
| SURFACE_LACE_CUT_DIR | Surface lace cut direction | |
| SURFACE_OUTPUT_PREF | Surface output preference | |
| SURFACE_CUT_OPT | Surface cut option | |
| SURFACE_OFFSET_SURFS | Surface offset surfaces option | |
| SURFACE_ONE_PASS | Surface one pass option | |
| SURFACE_CONSTRAIN | Surface constraint amount | |
| SURFACE_RETRACT_OPT | Surface retract option | |
| SURFACE_STAY_IN_STOCK | Surface stay in stock option | |
| SURFACE_CLEAR_STOCK | Surface clear stock amount | |
| SURFACE_CLEAR_STOCK_TYPE | Surface clear stock type | |
| SURFACE_CUT_OVER_EDGES | Surface cut over edges | |
| SURFACE_SKIP_FLATS | Surface skip flats option | |
| SURFACE_CURVE_CUT_DIR | Surface curve cut direction | |
| SFLOW_MACH_DIR | Surface flow machining direction | |
| SFLOW_MACH_ZORDER | Surface flow machining Z order | |
| SFLOW_TRAVEL_AROUND_MODE | Surface flow travel around mode | |
| SFLOCUT_TYPE | Surface flow cut type | |
| INTERSECT_TYPE | Type | |
| INTERSECT_CUTS_TYPE | Cut type | |
| INTERSECT_PASS_TYPE | Pass type | |
| INTERSECT_CLEANUP_FROM | Cleanup from option | |
| INTERSECT_PASSES_PER_SIDE | Number of passes per side | |
| LROUGH_ROUND_CORNERS | Lathe rough round corners option | |
| LROUGH_EXIT_PERP | Lathe rough exit perpendicular option | |
| LROUGH_XPLUS | Lathe rough cuts in X plus direction | |
| LROUGH_XMINUS | Lathe rough cuts in X minus direction | |
| LROUGH_ZPLUS | Lathe rough cuts in Z plus direction | |
| LROUGH_ZMINUS | Lathe rough cuts in Z minus direction | |
| LROUGH_AUTOFIN | Lathe rough auto finish option | |
| LROUGH_SPINDLE_DIR | Lathe rough spindle direction | |
| LROUGH_CONSTANT_PATH | Lathe rough constant path option | |
| WALL_STEP | Wall step amount | |
| WALL_TOP_TO_BOTTOM | Wall cut from top to bottom | |
| WALL_SAME_DIR | Wall same direction option | |
| WALL_DCEP_SIDE | Wall DCEP side value | |
| WALL_SWEPT_POCKET | Wall uses swept pockets | |
| WALL_SWEPT_ISLAND | Wall uses swept islands | |
| CUT_SIDE | Cut side | |
| S_USE_ADV_TOL | Use advanced tolerance | |
| M_USE_ADV_TOL | Use advanced tolerance | |
| WALL_MODE | Wall mode | |
| INTER_OP_OVERRIDE | Interop override option | |
| UTIL_TYPE | Utility type | |
| MD_FROM_TOOL | Multi-depth from tool | |
| MD_VARY_WITH_GEO | Multi-depth vary with geometry | |
| MD_VARY_WITH_FEAT | Multi-depth vary with feature | |
| MD_RETRACT_LEVEL | Multi-depth retract level | |
| CONTOUR_ENTRY_RAMP_TYPE | Contour entry ramp type | |
| CONTOUR_ENTRY_HELIX_TYPE | Contour entry helix type | |
| CONTOUR_RAMP_DOWN | 1=Ramp Down | 10.5.18 |
| CONTOUR_NUM_EXTRA_OFFSETS | Number of extra offsets | 10.5.18 |
| PREFER_SUBS | Prefer subs setting | |
| START_SYNC | Start sync number | |
| END_SYNC | End sync number | |
| STROKE_SYNC | Stroke sync number | |
| DRILL_BORE_CUT_TYPE | Drill bore cut type | |
| ADV_EXIT_SAME_AS_ENTRY | 1=Exit values are same as entry | 10.2.22 |
| ADV_ENTRY_TYPE | Entry type | 10.2.22 |
| ADV_EXIT_TYPE | Exit type | 10.2.22 |
| ADV_LINE_ENTRY_USE_CRC | 1=Line Entry uses CRC | 10.2.22 |
| ADV_LINE_ENTRY_USE_OFF_PART_LINE | 1=Line Entry uses Off Part Line | 10.2.22 |
| ADV_LINE_ENTRY_USE_RAMP | 1=Line Entry uses Ramp | 10.2.22 |
| ADV_LINE_ENTRY_RAMP_INCLUDE_LINE | 1=Line Entry Ramp uses Include Line | 10.2.22 |
| ADV_LINE_EXIT_USE_CRC | 1=Line Exit uses CRC | 10.2.22 |
| ADV_LINE_EXIT_USE_OFF_PART_LINE | 1=Line Exit uses Off Part Line | 10.2.22 |
| ADV_LINE_EXIT_USE_RAMP | 1=Line Exit uses Ramp | 10.2.22 |
| ADV_LINE_EXIT_RAMP_INCLUDE_LINE | 1=Line Exit Ramp uses Include Line | 10.2.22 |
| ADV_ARC_ENTRY_USE_CRC | 1=Arc Entry uses CRC | 10.2.22 |
| ADV_ARC_ENTRY_USE_OFF_PART_LINE | 1=Arc Entry uses Off Part Line | 10.2.22 |
| ADV_ARC_ENTRY_USE_RAMP | 1=Arc Entry uses Ramp | 10.2.22 |
| ADV_ARC_ENTRY_RAMP_INCLUDE_RADIUS | 1=Arc Entry Ramp uses Include Radius | 10.2.22 |
| ADV_ARC_EXIT_USE_CRC | 1=Arc Exit uses CRC | 10.2.22 |
| ADV_ARC_EXIT_USE_OFF_PART_LINE | 1=Arc Exit uses Off Part Line | 10.2.22 |
| ADV_ARC_EXIT_USE_RAMP | 1=Arc Exit uses Ramp | 10.2.22 |
| ADV_ARC_EXIT_RAMP_INCLUDE_RADIUS | 1=Arc Exit Ramp uses Include Radius | 10.2.22 |
| DRILL_REVERSE_ORDER | Drill cycle has Reverse Order checked | 10.2.22 |
| BAXIS_USED | B Axis Turning is used | 10.2.22 |
| BAXIS_METHOD | B Axis Turning Method | 10.2.22 |
| BAXIS_MULTI_TRANS | B Axis Turning uses multiple transitions | 10.2.22 |
| BAXIS_USE_MIN_ANGLE | B Axis Turning Minimum Angle | 10.2.22 |
| BAXIS_USE_MAX_ANGLE | B Axis Turning Maximum Angle | 10.2.22 |
| BAXIS_SMOOTH_CORNERS | B Axis Turning uses Smooth Corners option | 10.2.22 |
| BAXIS_VECTOR_TYPE | B Axis Turning Vector Type | 10.2.22 |
| BAXIS_CHECK_COLLISIONS | B Axis Turning uses Collision Checking | 10.2.22 |
| LOCK_ADV_APP_RET | 1=Lock Advanced Approach / Return Options | 14.0.26 |
| LOCK_ENTRY_CLEAR | 1=Lock Entry Clear | 10.2.22 |
| LOCK_EXIT_CLEAR | 1=Lock Exit Clear | 10.2.22 |
| LOCK_ENTRY_FEED | 1=Lock Entry Feed | 10.2.22 |
| LOCK_CONTOUR_FEED | 1=Lock Contour Feed | 10.2.22 |
| LOCK_RPM | 1=Lock Speed | 10.2.22 |
| LOCK_CSS | 1=Lock CSS | 10.2.22 |
| LOCK_MAX_RPM | 1=Lock Max RPM | 10.2.22 |
| LOCK_WRAP_START_ANGLE | 1=Lock Start Angle | 10.2.22 |
| LOCK_WRAP | 1=Lock Wrap | 10.2.22 |
| LOCK_WRAP_DUPS | 1=Lock Num Copies | 10.2.22 |
| LOCK_WRAP_DUP_ANGLE | 1=Lock Duplicate Angle | 10.2.22 |
| LOCK_COOLANT | 1=Lock Coolant | 10.2.22 |
| LOCK_DWELL | 1=Lock Dwell | 10.2.22 |
| LOCK_PROG_STOP | 1=Lock Program Stop | 10.2.22 |
| LOCK_PATTERN_ON | 1=Lock Pattern | 10.2.22 |
| LOCK_LEN_OFFSET | 1=Lock Tl Offset | 10.2.22 |
| LOCK_CRC | 1=Lock CRC | 10.2.22 |
| LOCK_CRC_OFFSET | 1=Lock CRC Offset | 10.2.22 |
| LOCK_PREFER_CANNED | 1=Lock Prefer Canned | 10.2.22 |
| LOCK_AUTOFIN | 1=Lock Auto Finish | 10.2.22 |
| LOCK_POS_APPROACH | 1=Lock Pos Approach | 10.2.22 |
| LOCK_TAP_PERCENT | 1=Lock Tap percent | 10.2.22 |
| LOCK_UTIL_MARKERS | 1=Lock Utility Markers | 10.2.22 |
| THREAD_MILL_RAPID_TO_FROM_CLEAR | 1=Rapid to/from Clearance Diameter | 10.3.11 |
| THREAD_MILL_PLUNGE_AT_CENTER | 0=Plunge at center, 1=Plunge at Diameter | 10.3.11 |
| THREAD_MILL_VARY_WITH_GEO | 1=Vary depth with geometry | 10.3.11 |
| THREAD_MILL_ENTRY_EXIT_METHOD | Entry/Exit method | 10.3.11 |
| THREAD_MILL_ENTRY_EXIT_RAD | Entry/Exit radius | 10.3.11 |
| THREAD_MILL_CUT_TYPE | 0=One Top Pass, 1=One Finish Pass, 3=Const Cut 3=Const Load | 10.3.11 |
| THREAD_MILL_DO_LAST_CUT | 1=Specify exact depth of last cut | 10.3.11 |
| THREAD_MILL_NUM_SPRING_PASSES | Number of Spring Passes | 10.3.11 |
| THREAD_MILL_START_DEPTH_TYPE | 0=Abs Z, 1=Top of Hole, 2=Seg Start, 3=Seg End | 10.3.11 |
| THREAD_MILL_END_DEPTH_TYPE | 0=Top, 1=Chamfer, 2=Mid, 3=Bottom, 4=Seg start, 5=Seg end, 6=Abs | 10.3.11 |
| THREAD_MILL_START_SEGNUM | Start Depth Segment Number | 10.3.11 |
| THREAD_MILL_END_SEGNUM | End Depth Segment Number | 10.3.11 |
| THREAD_MILL_SEGMENT_MATCH | 1=Use Segment Matching | 10.3.11 |
| THREAD_MILL_SEG_MATCH_LEN | 1=Match Segment Length | 10.3.11 |
| THREAD_MILL_SEG_MATCH_DIA | 1=Match Segment Diameter | 10.3.11 |
| THREAD_MILL_SEG_MATCH_TAPER | 1=Match Segment Taper | 10.3.11 |
| THREAD_MILL_SEG_MATCH_METHOD | 1=Match Segment Method | 10.3.11 |
| THREAD_MILL_DIM_FROM_TOOL | 0=Dimension from Hole, 1=Dimension from Tool | 10.3.11 |
| THREAD_MILL_BOTTOM_UP | 0=Top down, 1=Bottom Up | 10.3.11 |
| USING_ADV_APPROACH | 0=Do not use, 1=Use Advanced Approach | 14.0.25 |
| USING_ADV_RETRACT | 0=Do not use, 1=Use Advanced Retract | 14.0.25 |
| ADV_RETRACT_AS_REVERSE_APPROACH | 0=Unchecked, 1=Checked | 14.0.25 |
| ADV_TURN_CLEAR_DIR | 0=Auto, 1-Face, 2=OD | 14.0.25 |
