Operation Floating Point
From Macros Wiki
Jump to navigationJump to search
| Parameter | Description | Version Number |
|---|---|---|
| ENTRY_CLEAR | Entry clearance value | |
| EXIT_CLEAR | Exit clearance value | |
| ENTRY_FEED | Entry feedrate | |
| CONTOUR_FEED | Contour feedrate | |
| CUT_WIDTH | Cut width | |
| DRILL_CLEAR_PLANE | Drill clearance plane height | |
| STOCK | Stock amount | |
| BOSS_STOCK | Boss stock amount | |
| RPM | Spindle speed | |
| TIME | Time | |
| LENGTH | Length | |
| CSS | Constant surface speed value | |
| SURFACE_STOCK | Surface stock amount | |
| SURF_STOCK | Surface stock | |
| LATHE_STOCK_X | Lathe stock in X | |
| LATHE_STOCK_Z | Lathe stock in Z | |
| LATHE_CUT_WIDTH | Cut width | |
| CUT_TOL | Cut tolerance | |
| STEP | Step value | |
| DEPTH | Depth | |
| OD_ID_FACE | OD ID Face setting | |
| LATHE_DEPTH | Depth of cut | |
| DRILL_DWELL | Drill cycle dwell amount | |
| DRILL_TAP_PERCENT | Tap percentage | |
| DRILL_PECK_CLEARANCE | Drill peck clearance | |
| DRILL_PECK_AMOUNT | Drill peck depth | |
| DRILL_PECK_RETRACT | Drill peck retract amount | |
| DRILL_BORE_PULLOFF | Bore pulloff amount | |
| DRILL_CB_START_RIZ | Drill cycle start RIZ | |
| DRILL_CB_END_RIZ | Drill cycle end RIZ | |
| SURFACE_DEPTH | Surface depth | |
| MATERIAL_ONLY_CLEARANCE | Material only clearance | |
| LTHREAD_ANGLE | Lathe thread angle | |
| LTHREAD_NOMINAL_XD | Nominal diameter | |
| LTHREAD_TPI | Lathe thread number of TPI | |
| LTHREAD_PITCH | Lathe thread pitch | |
| LTHREAD_SLOPE | Lathe thread slope value | |
| LTHREAD_MINOR_XD | Lathe thread minor diameter | |
| LTHREAD_HEIGHT_XR | Lathe thread height as a radial value | |
| LTHREAD_RUN_IN_X | Run in amount in X | |
| LTHREAD_RUN_IN_Z | Run in amount in Z | |
| LTHREAD_RUN_OUT_X | Run out amount in X | |
| LTHREAD_RUN_OUT_Z | Run out amount in Z | |
| LTHREAD_FIRST_CUT | Lathe thread first cut option | |
| LTHREAD_LAST_CUT | Lathe thread last cut option | |
| LPLUNGE_MAX_CUT | Lathe plunge maximum cut | |
| LPLUNGE_ANGLE | Lathe plunge angle | |
| LPLUNGE_PECK_AMOUNT | Lathe plunge peck amount | |
| LPLUNGE_PECK_CLEARANCE | Lathe plunge peck clearance | |
| LPLUNGE_PECK_RETRACT | Lathe plunge peck retract amount | |
| LPLUNGE_FEED_PERCENT | Lathe plunge feed percentage | |
| LPLUNGE_ENTRY_TYPE | Lathe plunge entry type | |
| LATHE_PATTERN_SHIFT_CUT_X | Pattern shift cut amount in X | |
| LATHE_PATTERN_SHIFT_CUT_Z | Pattern shift cut amount in Z | |
| LATHE_PATTERN_SHIFT_PT_X | Pattern shift point in X | |
| LATHE_PATTERN_SHIFT_PT_Z | Pattern shift point in Z | |
| WRAP_START_ANGLE | Wrap start angle,same as option in Rotate tab | |
| WRAP_DUPS | Wrap duplication number,same as option in Rotate tab | |
| WRAP_DUP_ANGLE | Wrap duplication angle,same as option in Rotate tab | |
| LATHE_MAX_RPM | Maximum RPM | |
| POCKET_ENTRY_PLUNGE_PT_X | Pocket entry point in X | |
| POCKET_ENTRY_PLUNGE_PT_Y | Pocket entry point in Y | |
| POCKET_ENTRY_RAMP_SLOPE | Pocket entry ramp slope | |
| POCKET_ENTRY_RAMP_START_Z | Pocket entry ramp start Z position | |
| POCKET_ENTRY_RAMP_MAX_CUT | Pocket entry ramp maximum cut | |
| POCKET_ENTRY_RAMP_WALL_CLEAR | Pocket entry ramp wall clearance | |
| POCKET_ENTRY_RAMP_ANGLE | Pocket entry ramp angle | |
| POCKET_ENTRY_HELIX_SLOPE | Pocket entry slope | |
| POCKET_ENTRY_HELIX_ANGLE | Pocket entry helix angle | |
| POCKET_ENTRY_HELIX_START_Z | Pocket entry start Z | |
| POCKET_ENTRY_HELIX_MAX_CUT | Pocket entry maximum cut | |
| POCKET_ENTRY_HELIX_WALL_CLEAR | Pocket entry wall clearance | |
| POCKET_ENTRY_HELIX_DIA | Pocket entry helix diameter | |
| POCKET_ENTRY_HELIX_CP_X | Pocket entry helix X center | |
| POCKET_ENTRY_HELIX_CP_Y | Pocket entry helix Y center | |
| POCKET_ENTRY_PERIPH_START_Z | Pocket entry periphery start Z position | |
| POCKET_ENTRY_PERIPH_SLOPE | Pocket entry periphery slope | |
| SURFACE_ENTRY_PLUNGE_PT_X | Surface entry plunge point in X | |
| SURFACE_ENTRY_PLUNGE_PT_Y | Surface entry plunge point in Y | |
| RAPID_CLEARANCE | Rapid clearance | |
| ENTRY_LINE_LEN | Entry line length | |
| EXIT_LINE_LEN | Exit line length | |
| ENTRY_RAD | Entry arc radius | |
| EXIT_RAD | Exit arc radius | |
| Z_STEP_WANTED | Z stepover desired | |
| OVERHANG | Overhang amount | |
| OVERLAP | Overlap amount | |
| OPEN_CLEARANCE | Open clearance value | |
| MTHREAD_START_THREAD | Thread mill start thread | |
| MTHREAD_END_THREAD | Thread mill end thread value | |
| MTHREAD_CUT_DIA | Thread mill cut diameter | |
| MTHREAD_CLEAR_DIA | Thread mill clear diameter | |
| MTHREAD_PITCH | Thread mill pitch | |
| MTHREAD_FEED | Thread mill feedrate | |
| SURFACE_STEP_OVER | Surface stepover | |
| SURFACE_RIDGE_HEIGHT | Surface ridge height | |
| SURFACE_CUT_ANGLE | Surface cut angle | |
| SURFACE_DESIRED_Z | Surface desired Z depth | |
| SURFACE_CONSTRAINT_FACES_CLEAR | Surface constraint faces clear option | |
| SURFACE_STOCK_TOL | Surface stock tolerance | |
| SURFACE_FIXTURE_TOL | Surface fixture tolerance | |
| SURFACE_CONSTRAINT_TOL | Surface constraint tolerance | |
| SURFACE_SMOOTH_TOL | Surface smoothing tolerance | |
| SURFACE_ARC_FIT_TOL | Surface arc fit tolerance | |
| SURFACE_SPLINE_TOL | Surface spline tolerance | |
| SURFACE_NORMAL_ANGLE | Surface normal angle | |
| SURFACE_STEP_CUT_RATIO | Surface stepover cut ration | |
| SURFACE_CORNER_RAD | Surface corner radius | |
| SURFACE_MAX_CUT_ANGLE | Surface maximum cut angle | |
| CP1 | CP1 value | |
| CURVE_TOLERANCE | Curver tolerance | |
| AUTO_ENTRY_CP | Entry clear plane height | |
| AUTO_ENTRY_CLEAR_RAD | Entry move clear radius | |
| AUTO_EXIT_CP | Exit clear plane height | |
| AUTO_EXIT_CLEAR_RAD | Exit move clear radius | |
| GEO_RAD | Geometry radius | |
| MIN_RAD | Minimum radius | |
| Z_STEP | Actual Z stepover | |
| FM_CLEAR | Clearance option | |
| FM_CUT_WIDTH | Cut width | |
| CUT_ANGLE | Cut angle | |
| STEPOVER_FEED | Stepover feed value | |
| CLEAR_FEED | Clearance feedrate | |
| SCALLOP_FEED | Scallop feed amount | |
| MIN_CUT | Minimum cut | |
| PAST_STOCK | Past stock amount | |
| LTHREAD_Z_START | Lathe thread Z start position | |
| LTHREAD_Z_END | Lathe thread Z end position | |
| LTHREAD_MAJOR_DIA | Lathe thread major diameter | |
| LATHE_SURFACE_Z | Surface z value | |
| LROUGH_MIN_RAD | Lathe rough minimum radius | |
| LROUGH_ENTRY_LINE | Lathe rough entry line option | |
| LROUGH_ENTRY_RAD | Lathe rough entry arc radius | |
| LROUGH_EXIT_RAD | Lathe rough exit arc radius | |
| LROUGH_EXIT_LINE | Lathe rough exit line option | |
| LROUGH_START | Lathe rough start option | |
| LROUGH_CUT_WIDTH | Lathe rough cut width | |
| LROUGH_RAMP_ANGLE | Lathe rough ramp angle | |
| WALL_TOP | Wall top | |
| WALL_ANG | Wall angle | |
| WALL_BOT | Wall bottom value | |
| WALL_ITOP | Internal wall top | |
| WALL_IANG | Internal wall angle | |
| WALL_IBOT | Internal wall bottom | |
| WALL_USER_STEP | Wall user step amount | |
| WALL_SHAPE_STEP | Wall uses shape step | |
| WALL_RIDGE_HEIGHT | Wall ridge height | |
| DRILL_CLEAR_PLANE_LOC_CS | Use local CS | |
| MSURF_CLEAR | Surface clearance | |
| MSURF_STOCK_TOL | Surface stock tolerance | |
| MFIXTURE_TOL | Mill fixture tolerance | |
| M_ZSHIFT | Z shift value | |
| CONTOUR_EXTRA_OFFSETS_VAL | Extra offsets values | 10.5.18 |
| CONTOUR_ENTRY_RAMP_SLOPE | Contour entry ramp slope | |
| CONTOUR_ENTRY_RAMP_START_Z | Contour entry ramp start Z | |
| CONTOUR_ENTRY_RAMP_MAX_CUT | Contour entry ramp maximum cut | |
| CONTOUR_ENTRY_RAMP_ANGLE | Contour entry ramp angle | |
| CONTOUR_ENTRY_HELIX_SLOPE | Contour entry helix slope | |
| CONTOUR_ENTRY_HELIX_START_Z | Contour entry helix start Z | |
| CONTOUR_ENTRY_HELIX_MAX_CUT | Contour entry helix maximum cut | |
| CONTOUR_ENTRY_HELIX_DIA | Contour entry helix diameter | |
| DRILL_BORE_CUT_DIA | Drill bore cut diameter | |
| DRILL_BORE_CLEAR_DIA | Drill bore clear diameter | |
| DRILL_BORE_CLEAR_AMOUNT | Drill bore clear amount | |
| DRILL_BORE_ENTRY_EXIT_RAD | Drill bore entry and exit radius | |
| DRILL_BORE_ENTRY_EXIT_LINE | Drill bore entry and exit line length | |
| DRILL_BORE_CUT_WIDTH | Drill bore cut width | |
| DRILL_BORE_STOCK | Drill bore stock amount | |
| DRILL_BORE_OVERLAP | Drill bore overlap amount | |
| DRILL_BORE_APPROACH_ANGLE | Drill bore approach angle | |
| DRILL_BORE_DESIRED_STEP | Drill bore desired step | |
| ADV_LINE_ENTRY_OFF_PART_LINE | Line Entry Off Part Line value | 10.2.22 |
| ADV_LINE_ENTRY_OFF_PART_ANGLE | Line Entry Off Part Line angle | 10.2.22 |
| ADV_LINE_ENTRY_OFF_PART_DIST | Line Entry Off Part distance | 10.2.22 |
| ADV_LINE_ENTRY_RAMP_DIST | Line Entry Ramp distance | 10.2.22 |
| ADV_LINE_EXIT_OFF_PART_LINE | Line Exit Off Part Line value | 10.2.22 |
| ADV_LINE_EXIT_OFF_PART_ANGLE | Line Exit Off Part Line angle | 10.2.22 |
| ADV_LINE_EXIT_OFF_PART_DIST | Line Exit Off Part distance | 10.2.22 |
| ADV_LINE_EXIT_RAMP_DIST | Line Exit Ramp distance | 10.2.22 |
| ADV_ARC_ENTRY_OFF_PART_LINE | Arc Entry Off Part Line value | 10.2.22 |
| ADV_ARC_ENTRY_OFF_PART_DIST | Arc Entry Off Part distance | 10.2.22 |
| ADV_ARC_ENTRY_RAMP_DIST | Arc Entry Ramp distance | 10.2.22 |
| ADV_ARC_EXIT_OFF_PART_LINE | Arc Exit Off Part Line value | 10.2.22 |
| ADV_ARC_EXIT_OFF_PART_DIST | Arc Exit Off Part distance | 10.2.22 |
| ADV_ARC_EXIT_RAMP_DIST | Arc Exit Ramp distance | 10.2.22 |
| LROUGH_END_LIMIT_VAL | lathe Roughing End Limit Value | 10.2.22 |
| BAXIS_MIN_ANGLE_VAL | B Axis Turning, Minimum Angle | 10.2.22 |
| BAXIS_MAX_ANGLE_VAL | B Axis Turning, Maximum Angle | 10.2.22 |
| BAXIS_LEAD_LAG_ANGLE | B Axis Turning, Lead Lag Angle | 10.2.22 |
| BAXIS_COLLISION_CLEARANCE | B Axis Turning, Collision Check Clearance | 10.2.22 |
| THREAD_WHIRL_NUM_FLUTES | Number of Flutes | 10.2.22 |
| THREAD_WHIRL_FEED_PER_FLUTE | Feed Per Flute | 10.2.22 |
| THREAD_WHIRL_FEED | Feed | 10.2.22 |
| THREAD_WHIRL_PITCH | Pitch (mm) | 10.2.22 |
| THREAD_WHIRL_RPM | Spindle Speed | 10.2.22 |
| THREAD_WHIRL_CP2 | Entry Clear Z | 10.2.22 |
| THREAD_WHIRL_CP3 | Exit Clear Z | 10.2.22 |
| THREAD_WHIRL_IN_X | Run In X | 10.2.22 |
| THREAD_WHIRL_IN_Z | Run In Z | 10.2.22 |
| THREAD_WHIRL_OUT_X | Run Out X | 10.2.22 |
| THREAD_WHIRL_OUT_Z | Run Out Z | 10.2.22 |
| THREAD_WHIRL_START_X | Start X | 10.2.22 |
| THREAD_WHIRL_START_Z | Start Z | 10.2.22 |
| THREAD_WHIRL_END_X | End X | 10.2.22 |
| THREAD_WHIRL_END_Z | End Z | 10.2.22 |
| THREAD_WHIRL_APP_X | Approach X | 10.2.22 |
| THREAD_WHIRL_APP_Z | Approach Z | 10.2.22 |
| THREAD_WHIRL_RET_X | Retract X | 10.2.22 |
| THREAD_WHIRL_RET_Z | Retract Z | 10.2.22 |
| THREAD_WHIRL_COOLANT | Coolant Type | 10.2.22 |
| THREAD_WHIRL_CONST_FEED_ON | 1=Constant Feed On | 10.2.22 |
| THREAD_WHIRL_CONST_FEED_VAL | Constant Feed value | 10.2.22 |
| THREAD_WHIRL_C_OFFSET | Type of C Offset | 10.2.22 |
| THREAD_WHIRL_START_C_OFFSET | C Offset Start | 10.2.22 |
| THREAD_WHIRL_END_C_OFFSET | C Offset End | 10.2.22 |
| THREAD_MILL_PLUNGE_DIA | Plunge diameter | 10.3.11 |
| THREAD_MILL_ENTRY_FEED | Entry feedrate | 10.3.11 |
| THREAD_MILL_CRC_LINE | CRC line length | 10.3.11 |
| THREAD_MILL_ENTRY_ANGLE | Entry angle | 10.3.11 |
| THREAD_MILL_EXIT_ANGLE | Exit angle | 10.3.11 |
| THREAD_MILL_ENTRY_EXIT_RAD | Entry/Exit radius | 10.3.11 |
| THREAD_MILL_THREAD_HEIGHT | Thread height | 10.3.11 |
| THREAD_MILL_CUT_DEPTH | Depth of first cut | 10.3.11 |
| THREAD_MILL_LAST_CUT_AMOUNT | Last cut amount | 10.3.11 |
| THREAD_MILL_TAPER_ANGLE | Taper angle | 10.3.11 |
| THREAD_MILL_ADJUST_DEPTH_DELTA | Amount to adjust end depth | 10.3.11 |
| THREAD_MILL_START_DEPTH | Start depth Z | 10.3.11 |
| THREAD_MILL_END_DEPTH | End depth Z | 10.3.11 |
