All Parameters
From Macros Wiki
Jump to navigationJump to search
| Variable | Description | Used by | Version Number |
| ABS_MOVES | Post output is in absolute | SET_POST_DATA | 9, 0, 0 |
| ADV_ARC_ENTRY_CRC | Advanced entry/exit has CRC checked in radius entry section | PROC_DATA | 9, 5, 13 |
| ADV_ARC_ENTRY_RAD | Advanced entry/exit has radius entry selected | PROC_DATA | 9, 5, 13 |
| ADV_ARC_EXIT_CRC | Advanced entry/exit has CRC checked in radius exit section | PROC_DATA | 9, 5, 13 |
| ADV_ARC_EXIT_RAD | Advanced entry/exit has radius selected in exit section | PROC_DATA | 9, 5, 13 |
| ADV_LINE_ENTRY_CRC | Advanced entry/exit has CRC checked in line entry section | PROC_DATA | 9, 5, 13 |
| ADV_LINE_EXIT_CRC | Advanced entry/exit has CRC checked in line exit section | PROC_DATA | 9, 5, 13 |
| AFR_BLIND_BOTTOM_ADJUST | AFR amount to adjust bottom of blind holes | SET_HOLEFR_PARAM | 9, 5, 14 |
| AFR_CLEAR_PLANE_TOL | AFR clearance plane tolerance | SET_HOLEFR_PARAM | 9, 5, 14 |
| AFR_CS_MODE | AFR CS creation option | SET_HOLEFR_PARAM | 9, 5, 14 |
| AFR_CS1_ORIGIN | AFR CS1 origin option | SET_HOLEFR_PARAM | 9, 5, 14 |
| AFR_MATCH_MODE | AFR match mode | SET_HOLEFR_PARAM | 9, 5, 14 |
| AFR_SELECT_MODE | AFR selection mode | SET_HOLEFR_PARAM | 9, 5, 14 |
| AFR_THRU_BOTTOM_ADJUST | AFR amount to adjust bottom of through holes | SET_HOLEFR_PARAM | 9, 5, 14 |
| AFR_TOP_CLEAR | AFR top clearance amount | SET_HOLEFR_PARAM | 9, 5, 14 |
| AFR_WG_NAME | AFR WorkGroup name; | SET_HOLEFR_PARAM | 9, 5, 14 |
| ALLOY | Material alloy option | PART_DATA | 9, 0, 0 |
| AUTO_CLEAR_ON | Auto clearance is on | PART_DATA | 9, 0, 0 |
| AUTO_CLEAR_VAL | Auto clearance value | PART_DATA | 9, 0, 0 |
| AUTO_ENTRY_CLEAR_RAD | Entry move clear radius | OP_DATA - PROC_DATA | 9, 0, 0 |
| AUTO_ENTRY_CP | Entry clear plane height | OP_DATA - PROC_DATA | 9, 0, 0 |
| AUTO_EXIT_CLEAR_RAD | Exit move clear radius | OP_DATA - PROC_DATA | 9, 0, 0 |
| AUTO_EXIT_CP | Exit clear plane height | OP_DATA - PROC_DATA | 9, 0, 0 |
| AUTO_REMOVE | Auto remove option | UTIL_PROC_DATA | 9, 0, 0 |
| AXIS_INFO | Axis info | PROC_DATA | 9, 0, 0 |
| BACK_FORTH | Back and Forth is checked | OP_DATA | 9, 0, 0 |
| BOSS_STOCK | Boss stock (island stock) amount | OP_DATA - PROC_DATA | 9, 0, 0 |
| C_SYNCHED | C Synched is checked | UTIL_PROC_DATA | 9, 0, 0 |
| CHUCK_PART_LEN | Chuck part length | SET_POST_DATA | 9, 0, 0 |
| CHUCK_WIDTH | Chuck width | SET_POST_DATA | 9, 0, 0 |
| CLEAR_DIA | Clearance diameter | SET_POST_DATA | 9, 0, 0 |
| CLEAR_FEED | Clearance feedrate | OP_DATA - PROC_DATA | 9, 0, 0 |
| CLEAR_FEED_LOCK | Clearance feed lock is checked | OP_DATA - PROC_DATA | 9, 0, 0 |
| CLEAR_PERIPH | Clear periphery is selected | OP_DATA - PROC_DATA | 9, 0, 0 |
| CLEAR_RAD | Clearance radius | PART_DATA - SET_POST_DATA | 9, 0, 0 |
| CLEAR_Z | Clearance Z value; | SET_POST_DATA | 9, 0, 0 |
| COMMENT | Comment text | PART_DATA - TOOL_DATA | 9, 0, 0 |
| COMMENT | Comment text | PROC_DATA - OP_DATA | 9, 0, 0 |
| COMMENTS | Comments is checked | SET_POST_DATA | 9, 0, 0 |
| CONTOUR_ENTRY_HELIX_DIA | Contour entry helix diameter | OP_DATA - PROC_DATA | 9, 0, 0 |
| CONTOUR_ENTRY_HELIX_MAX_CUT | Contour entry helix maximum cut | OP_DATA - PROC_DATA | 9, 0, 0 |
| CONTOUR_ENTRY_HELIX_SLOPE | Contour entry helix slope | OP_DATA - PROC_DATA | 9, 0, 0 |
| CONTOUR_ENTRY_HELIX_START_Z | Contour entry helix start Z | OP_DATA - PROC_DATA | 9, 0, 0 |
| CONTOUR_ENTRY_HELIX_TYPE | Contour entry helix type | OP_DATA - PROC_DATA | 9, 0, 0 |
| CONTOUR_ENTRY_RAMP_ANGLE | Contour entry ramp angle | OP_DATA - PROC_DATA | 9, 0, 0 |
| CONTOUR_ENTRY_RAMP_MAX_CUT | Contour entry ramp maximum cut | OP_DATA - PROC_DATA | 9, 0, 0 |
| CONTOUR_ENTRY_RAMP_SLOPE | Contour entry ramp slope | OP_DATA - PROC_DATA | 9, 0, 0 |
| CONTOUR_ENTRY_RAMP_START_Z | Contour entry ramp start Z | OP_DATA - PROC_DATA | 9, 0, 0 |
| CONTOUR_ENTRY_RAMP_TYPE | Contour entry ramp type | OP_DATA - PROC_DATA | 9, 0, 0 |
| CONTOUR_FEED | Contour feedrate | OP_DATA - PROC_DATA | 9, 0, 0 |
| CONTROL_POINT | Control point (Tooltip) | UTIL_PROC_DATA | 9, 0, 0 |
| COOLANT | Coolant type | OP_DATA - PROC_DATA | 9, 0, 0 |
| CP1 | CP1 value | PART_DATA - OP_DATA - PROC_DATA | 9, 0, 0 |
| CRC | CRC state | PROC_DATA | 9, 0, 0 |
| CRC_DIR | CRC direction | OP_DATA | 9, 0, 0 |
| CRC_OFFSET | CRC offset number | OP_DATA - PROC_DATA | 9, 0, 0 |
| CRC_SIDE | CRC side | OP_DATA | 9, 0, 0 |
| CS | CS number | UTIL_PROC_DATA | 9, 0, 0 |
| CS_NUM | CS number | OP_DATA - PROC_DATA | 9, 0, 0 |
| CSS | Constant surface speed value | OP_DATA | 9, 0, 0 |
| CURVE_CUT_DIR | Curve cut direction | PROC_DATA | 9, 0, 0 |
| CURVE_TOL | Curve tolerance | PROC_DATA | 9, 0, 0 |
| CURVE_TOLERANCE | Curver tolerance | OP_DATA | 9, 0, 0 |
| CUSTOM_CBSET | Custom CBSET | PROC_DATA | 9, 3, 9 |
| CUT_ANGLE | Cut angle | OP_DATA - PROC_DATA | 9, 0, 0 |
| CUT_BACK | Cut back amount | OP_DATA - PROC_DATA | 9, 0, 0 |
| CUT_SIDE | Cut side | OP_DATA - PROC_DATA | 9, 0, 0 |
| CUT_TOL | Cut tolerance | OP_DATA | 9, 0, 0 |
| CUT_TYPE | Cut type | OP_DATA - PROC_DATA | 9, 0, 0 |
| CUT_WIDTH | Cut width | OP_DATA - PROC_DATA | 9, 0, 0 |
| DEPTH | Depth | OP_DATA | 9, 0, 0 |
| DEPTH_FIRST | Cut depth first | OP_DATA - PROC_DATA | 9, 0, 0 |
| DRAFT_ANGLE | Draft angle | TOOL_DATA | 9, 0, 0 |
| DRILL_BORE_APPROACH_ANGLE | Drill bore approach angle | OP_DATA - PROC_DATA | 9, 0, 0 |
| DRILL_BORE_CLEAR_AMOUNT | Drill bore clear amount | OP_DATA - PROC_DATA | 9, 0, 0 |
| DRILL_BORE_CLEAR_DIA | Drill bore clear diameter | OP_DATA - PROC_DATA | 9, 0, 0 |
| DRILL_BORE_CUT_DIA | Drill bore cut diameter | OP_DATA - PROC_DATA | 9, 0, 0 |
| DRILL_BORE_CUT_WIDTH | Drill bore cut width | OP_DATA - PROC_DATA | 9, 0, 0 |
| DRILL_BORE_DESIRED_STEP | Drill bore desired step | OP_DATA - PROC_DATA | 9, 0, 0 |
| DRILL_BORE_ENTRY_EXIT_LINE | Drill bore entry and exit line length | OP_DATA - PROC_DATA | 9, 0, 0 |
| DRILL_BORE_ENTRY_EXIT_RAD | Drill bore entry and exit radius | OP_DATA - PROC_DATA | 9, 0, 0 |
| DRILL_BORE_OVERLAP | Drill bore overlap amount | OP_DATA - PROC_DATA | 9, 0, 0 |
| DRILL_BORE_PULLOFF | Drill bore pulloff amount | OP_DATA - PROC_DATA | 9, 0, 0 |
| DRILL_BORE_STOCK | Drill bore stock amount | OP_DATA - PROC_DATA | 9, 0, 0 |
| DRILL_CB_END_RIZ | Drill cycle end RIZ | OP_DATA | 9, 0, 0 |
| DRILL_CB_START_RIZ | Drill cycle start RIZ | OP_DATA | 9, 0, 0 |
| DRILL_CLEAR_PLANE | Drill clearance plane height | OP_DATA - PROC_DATA | 9, 0, 0 |
| DRILL_CLEAR_PLANE_LOC_CS | Use local CS | OP_DATA | 9, 0, 0 |
| DRILL_DWELL | Drill cycle dwell amount | OP_DATA - PROC_DATA | 9, 0, 0 |
| DRILL_FEED | Drill feedrate | PROC_DATA | 9, 0, 0 |
| DRILL_PECK_AMOUNT | Drill peck depth | OP_DATA - PROC_DATA | 9, 0, 0 |
| DRILL_PECK_CLEARANCE | Drill peck clearance | OP_DATA - PROC_DATA | 9, 0, 0 |
| DRILL_PECK_RETRACT | Drill peck retract amount | OP_DATA - PROC_DATA | 9, 0, 0 |
| DRILL_POS_APPROACH | Use positive approach | OP_DATA - PROC_DATA | 9, 0, 0 |
| DRILL_TAP_PERCENT | Tap percentage | OP_DATA - PROC_DATA | 9, 0, 0 |
| DRILL_TYPE | Drill cycle type | OP_DATA - PROC_DATA | 9, 0, 0 |
| ENTRY_CLEAR | Entry clearance value | OP_DATA - PROC_DATA | 9, 0, 0 |
| ENTRY_FEED | Entry feedrate | OP_DATA - PROC_DATA | 9, 0, 0 |
| ENTRY_LINE | Use entry line | OP_DATA - PROC_DATA | 9, 0, 0 |
| ENTRY_LINE_LEN | Entry line length | OP_DATA - PROC_DATA | 9, 0, 0 |
| ENTRY_PERP | Entry is perpendicular | OP_DATA - PROC_DATA | 9, 0, 0 |
| ENTRY_RAD | Entry arc radius | OP_DATA - PROC_DATA | 9, 0, 0 |
| ENTRY_TYPE | Entry move type | OP_DATA - PROC_DATA | 9, 0, 0 |
| EXIT_CLEAR | Exit clearance value | OP_DATA - PROC_DATA | 9, 0, 0 |
| EXIT_LINE | Use exit line | OP_DATA - PROC_DATA | 9, 0, 0 |
| EXIT_LINE_LEN | Exit line length | OP_DATA - PROC_DATA | 9, 0, 0 |
| EXIT_PERP | Exit is perpendicular | OP_DATA - PROC_DATA | 9, 0, 0 |
| EXIT_RAD | Exit arc radius | OP_DATA - PROC_DATA | 9, 0, 0 |
| FAMILY | Material family | PART_DATA | 9, 0, 0 |
| FEED_CONNECT | Use feed connect. Toggles "Retracts" flag (inverse sense). | OP_DATA - PROC_DATA | 9, 0, 0 |
| FEED_DISTANCE | Feed distance | UTIL_PROC_DATA | 9, 0, 0 |
| FEEDRATE | Feedrate | UTIL_PROC_DATA | 9, 0, 0 |
| FLOW | Flow number | OP_DATA | 9, 0, 0 |
| FLOW_NUM | Flow number | UTIL_PROC_DATA | 9, 0, 0 |
| FM_BACK_AND_FORTH | Back and Forth setting | PROC_DATA | 9, 3, 9 |
| FM_BEFORE_ZIGZAG | Before zigzag option | PROC_DATA | 9, 3, 9 |
| FM_CLEAR | Clearance option | OP_DATA - PROC_DATA | 9, 0, 0 |
| FM_CUT_WIDTH | Cut width | OP_DATA - PROC_DATA | 9, 0, 0 |
| FM_HPLUS | Cut in Horizontal plus direction | OP_DATA - PROC_DATA | 9, 0, 0 |
| FM_MOVEH | Move horizontal | OP_DATA - PROC_DATA | 9, 0, 0 |
| FM_TYPE | Type | OP_DATA - PROC_DATA | 9, 0, 0 |
| FM_USE_SHAPE | Use shape | OP_DATA - PROC_DATA | 9, 0, 0 |
| FM_VPLUS | Cut in vertical plus direction | OP_DATA - PROC_DATA | 9, 0, 0 |
| FORM_SHAPE_REF | Shape reference number used for form tool | TOOL_DATA | 9, 5, 13 |
| FORWARD | Forward option | UTIL_PROC_DATA | 9, 0, 0 |
| FROM_WORKPIECE | Dimensions from workpiece | UTIL_PROC_DATA | 9, 0, 0 |
| FULL_DIA | Full diameter value | OP_DATA - PROC_DATA | 9, 0, 0 |
| FULL_RETURN | Full return option | UTIL_PROC_DATA | 9, 0, 0 |
| GEO_RAD | Geometry radius | OP_DATA - PROC_DATA | 9, 0, 0 |
| GRAPHIC_PART_DIST_ON | Graphic part distance on is checked | PART_DATA | 9, 0, 0 |
| GRAPHIC_PART_DIST_VAL | Graphic part distance value | PART_DATA | 9, 0, 0 |
| GRIP_Z | Grip Z value | UTIL_PROC_DATA | 9, 0, 0 |
| GROUP_ANG_TOL | Angular tolerance | SET_HOLEFR_PARAM | 9, 5, 14 |
| GROUP_KEEP | Keep in group | SET_HOLEFR_PARAM | 9, 5, 14 |
| GROUP_LIN_TOL | Linear tolerance value | SET_HOLEFR_PARAM | 9, 5, 14 |
| GROUP_MODE | Group mode | SET_HOLEFR_PARAM | 9, 5, 14 |
| GROUP_SAME_BOTTOM_Z | Group same bottom Z together | SET_HOLEFR_PARAM | 9, 5, 14 |
| GROUP_SAME_CS | Group same CS together | SET_HOLEFR_PARAM | 9, 5, 14 |
| GROUP_SAME_DIA | Group same diameter together | SET_HOLEFR_PARAM | 9, 5, 14 |
| GROUP_SAME_MID_Z | Group same mid Z together | SET_HOLEFR_PARAM | 9, 5, 14 |
| GROUP_SAME_TOP_Z | Group same top Z together | SET_HOLEFR_PARAM | 9, 5, 14 |
| GROUP_SAME_TYPE | Group same hole type together | SET_HOLEFR_PARAM | 9, 5, 14 |
| HARDNESS | Hardness value | PART_DATA | 9, 0, 0 |
| HIT_FLATS | Hit flats option | OP_DATA - PROC_DATA | 9, 0, 0 |
| HIT_PARALLEL | Hit parallel option | OP_DATA - PROC_DATA | 9, 0, 0 |
| HOLDER_SHAPE_REF | Reference number of shape used for tool holder | TOOL_DATA | 9, 0, 0 |
| HOLDER_SOLID_REF | Reference number of solid used for tool holder | TOOL_DATA | 9, 0, 0 |
| ID | Tool ID option | TOOL_DATA | 9, 0, 0 |
| IGNORE_TOOLS | Ignore tools option | OP_DATA - PROC_DATA | 9, 0, 0 |
| INITIAL_FACE_Z | Initial face Z value | UTIL_PROC_DATA | 9, 0, 0 |
| INTER_OP_OVERRIDE | Interop override option | OP_DATA | 9, 0, 0 |
| INTER_PART_FULL_UP | Inter part full up option | SET_POST_DATA | 9, 0, 0 |
| INTERSECT_CLEANUP_FROM | Cleanup from option | OP_DATA | 9, 0, 0 |
| INTERSECT_CUTS_TYPE | Cut type | OP_DATA | 9, 0, 0 |
| INTERSECT_PASS_TYPE | Pass type | OP_DATA | 9, 0, 0 |
| INTERSECT_PASSES_PER_SIDE | Number of passes per side | OP_DATA | 9, 0, 0 |
| INTERSECT_TYPE | Type | OP_DATA | 9, 0, 0 |
| LATHE_CANNED_AUTOFIN | Auto finish option | OP_DATA | 9, 0, 0 |
| LATHE_CLEAR_ID | Clear ID value | PROC_DATA | 9, 0, 0 |
| LATHE_CUT_DIR | Cut direction | OP_DATA | 9, 0, 0 |
| LATHE_CUT_OFF | Cut off value | OP_DATA | 9, 0, 0 |
| LATHE_CUT_OTHER_SIDE | Cut other side option | OP_DATA - PROC_DATA | 9, 0, 0 |
| LATHE_CUT_WIDTH | Cut width | OP_DATA | 9, 0, 0 |
| LATHE_DEPTH | Depth of cut | OP_DATA | 9, 0, 0 |
| LATHE_MAX_RPM | Maximum RPM | OP_DATA | 9, 0, 0 |
| LATHE_NO_DRAG | No drag option | OP_DATA | 9, 0, 0 |
| LATHE_OD_ID_FACE | OD ID Face setting (OD=0, ID=1, Front Face=3, Back Face [MTM]=4) | OP_DATA - PROC_DATA | 9, 0, 0 |
| LATHE_PAT_SHIFT_FIXED_SRT | Pattern shift fixed option | OP_DATA | 9, 0, 0 |
| LATHE_PAT_SHIFT_PASSES | Pattern shift number of passes | OP_DATA | 9, 0, 0 |
| LATHE_PATTERN_SHIFT_CUT_X | Pattern shift cut amount in X | OP_DATA | 9, 0, 0 |
| LATHE_PATTERN_SHIFT_CUT_Z | Pattern shift cut amount in Z | OP_DATA | 9, 0, 0 |
| LATHE_PATTERN_SHIFT_PT_X | Pattern shift point in X | OP_DATA | 9, 0, 0 |
| LATHE_PATTERN_SHIFT_PT_Z | Pattern shift point in Z | OP_DATA | 9, 0, 0 |
| LATHE_PLUNGE_CENTER_OUT | Plunge from center outwards | OP_DATA | 9, 0, 0 |
| LATHE_PLUNGE_CUT_TYPE | Plunge cut type | OP_DATA | 9, 0, 0 |
| LATHE_PLUNGE_ENTRY_TYPE | Plunge entry type | OP_DATA | 9, 0, 0 |
| LATHE_PLUNGE_TYPE | Plunge type | OP_DATA | 9, 0, 0 |
| LATHE_PREFER_CANNED | Prefer canned option | OP_DATA - PROC_DATA | 9, 0, 0 |
| LATHE_PULL_OFF_WALL | Pulloff wall value | OP_DATA | 9, 0, 0 |
| LATHE_ROUGH_TYPE | Rough cycle type | OP_DATA | 9, 0, 0 |
| LATHE_SQUARE_CORNERS | Square corners option | OP_DATA | 9, 0, 0 |
| LATHE_SURFACE_Z | Surface z value | OP_DATA | 9, 0, 0 |
| LATHE_TYPE | Lathe Process type | PROC_DATA | 9, 0, 0 |
| LATHE_TYPE | Lathe Operation type | OP_DATA | 9, 0, 0 |
| LATHE_USE_AUTO_CLEAR | Use auto clearance | PROC_DATA | 9, 4, 12 |
| LATHE_XZ_STOCK | Use XZ stock | OP_DATA | 9, 0, 0 |
| LDRILL_CLEARANCE | Lathe drill clearance value | PROC_DATA | 9, 0, 0 |
| LDRILL_DWELL | Lathe drill dwell amount | PROC_DATA | 9, 0, 0 |
| LDRILL_ENTRY | Lathe drill entry type | PROC_DATA | 9, 3, 9 |
| LDRILL_FEED | Lathe drill feed value | PROC_DATA | 9, 0, 0 |
| LDRILL_PECK | Lathe drill peck value | PROC_DATA | 9, 0, 0 |
| LDRILL_RETRACT | Lathe drill retract amount | PROC_DATA | 9, 0, 0 |
| LDRILL_SURFACE_Z | Lathe drill surface Z value | PROC_DATA | 9, 0, 0 |
| LDRILL_TAP_PERCENT | Lathe drill tap percentage | PROC_DATA | 9, 0, 0 |
| LDRILL_TIP_Z | Lathe drill Tip Z position | PROC_DATA | 9, 0, 0 |
| LEN_OFFSET | Length offset number | OP_DATA - PROC_DATA | 9, 0, 0 |
| LENGTH | Length | OP_DATA | 9, 0, 0 |
| LLTOOL_THICK | Lathe tool thickness | TOOL_DATA | 9, 0, 0 |
| LOCATION | Location value | UTIL_PROC_DATA | 9, 0, 0 |
| LOCKS | Locks setting | OP_DATA | 9, 0, 0 |
| LPLUNGE_ANGLE | Lathe plunge angle | OP_DATA | 9, 0, 0 |
| LPLUNGE_FEED_PERCENT | Lathe plunge feed percentage | OP_DATA | 9, 0, 0 |
| LPLUNGE_MAX_CUT | Lathe plunge maximum cut | OP_DATA | 9, 0, 0 |
| LPLUNGE_PECK_AMOUNT | Lathe plunge peck amount | OP_DATA | 9, 0, 0 |
| LPLUNGE_PECK_CLEARANCE | Lathe plunge peck clearance | OP_DATA | 9, 0, 0 |
| LPLUNGE_PECK_RETRACT | Lathe plunge peck retract amount | OP_DATA | 9, 0, 0 |
| LROUGH_AUTO_FINISH | Lathe rough auto finish option | PROC_DATA | 9, 0, 0 |
| LROUGH_AUTO_FINISH_FEED | Lathe rough auto finish feedrate | PROC_DATA | 9, 3, 9 |
| LROUGH_AUTOFIN | Lathe rough auto finish option | OP_DATA | 9, 0, 0 |
| LROUGH_AVOID_AIR | Lathe rough avoid air option | PROC_DATA | 9, 0, 0 |
| LROUGH_BACK_AND_FORTH | Lathe rough back and forth setting | PROC_DATA | 9, 5, 13 |
| LROUGH_CENTER_OUT | Lathe rough from center out | PROC_DATA | 9, 0, 0 |
| LROUGH_CLEANUP_PASS | Lathe rough use cleanup pass | PROC_DATA | 9, 0, 0 |
| LROUGH_CLEARANCE | Lathe rough clearance value | PROC_DATA | 9, 3, 9 |
| LROUGH_CONSTANT_PATH | Lathe rough constant path option | OP_DATA - PROC_DATA | 9, 0, 0 |
| LROUGH_CONSTANT_STEP | Lathe rough constant step option | PROC_DATA | 9, 0, 0 |
| LROUGH_CONTOUR_FEED | Lathe rough conmtour feedrate | PROC_DATA | 9, 3, 9 |
| LROUGH_CSS | Lathe rough constant surface speed value | PROC_DATA | 9, 0, 0 |
| LROUGH_CUT_DIR | Lathe rough cut direction | PROC_DATA | 9, 0, 0 |
| LROUGH_CUT_OFF | Lathe rough cut off value | PROC_DATA | 9, 0, 0 |
| LROUGH_CUT_WIDTH | Lathe rough cut width | PROC_DATA - OP_DATA | 9, 0, 0 |
| LROUGH_CUT_X | Lathe rough cut in X direction | PROC_DATA | 9, 0, 0 |
| LROUGH_CUT_Z | Lathe rough cut in Z direction | PROC_DATA | 9, 0, 0 |
| LROUGH_CYCLE_SP_X | Lathe rough cycle start point X value | PROC_DATA | 9, 5, 13 |
| LROUGH_CYCLE_SP_Z | Lathe rough cycle start point Z value | PROC_DATA | 9, 5, 13 |
| LROUGH_DEFLECT_COMP_VAL | Lathe rough deflection compensation value | PROC_DATA | 9, 4, 12 |
| LROUGH_DIR_FWD | Lathe rough direction forward | PROC_DATA | 9, 5, 13 |
| LROUGH_ENTRY_FEED | Lathe rough entry feedrate | PROC_DATA | 9, 3, 9 |
| LROUGH_ENTRY_LINE | Lathe rough entry line option | OP_DATA - PROC_DATA | 9, 0, 0 |
| LROUGH_ENTRY_PERP | Lathe rough entry perpendicular option | PROC_DATA | 9, 0, 0 |
| LROUGH_ENTRY_RAD | Lathe rough entry arc radius | OP_DATA - PROC_DATA | 9, 0, 0 |
| LROUGH_EXIT_LINE | Lathe rough exit line option | OP_DATA - PROC_DATA | 9, 0, 0 |
| LROUGH_EXIT_PERP | Lathe rough exit perpendicular option | OP_DATA - PROC_DATA | 9, 0, 0 |
| LROUGH_EXIT_RAD | Lathe rough exit arc radius | OP_DATA - PROC_DATA | 9, 0, 0 |
| LROUGH_FEED | Lathe rough feedrate | PROC_DATA | 9, 3, 9 |
| LROUGH_FEED_PERCENT | Lathe rough feed percentage | PROC_DATA | 9, 0, 0 |
| LROUGH_FINISH_LAST | Lathe rough finish last | PROC_DATA | 9, 0, 0 |
| LROUGH_FIXED_SP | Lathe rough uses fixed start point | PROC_DATA | 9, 0, 0 |
| LROUGH_MAX_RPM | Lathe rough maximum spindle speed | PROC_DATA | 9, 3, 9 |
| LROUGH_MIN_RAD | Lathe rough minimum radius | OP_DATA - PROC_DATA | 9, 0, 0 |
| LROUGH_MONOTONIC | Lathe rough is monotonic | PROC_DATA | 9, 0, 0 |
| LROUGH_MULTI_PASS | Lathe rough uses multiple passes | PROC_DATA | 9, 4, 12 |
| LROUGH_NUM_PASSES | Lathe rough number of passes | PROC_DATA | 9, 0, 0 |
| LROUGH_OFFSET_CUT_DEPTH | Lathe rough offset cycle cut depth | PROC_DATA | 9, 5, 13 |
| LROUGH_PECK | Lathe rough uses pecking | PROC_DATA | 9, 0, 0 |
| LROUGH_PECK_VAL | Lathe rough peck value | PROC_DATA | 9, 0, 0 |
| LROUGH_PLUNGE_ANGLE | Lathe rough plunge angle | PROC_DATA | 9, 0, 0 |
| LROUGH_PLUNGE_FIRST | Lathe rough plunge first | PROC_DATA | 9, 5, 13 |
| LROUGH_PLUNGE_TYPE | Lathe rough plunge type | OP_DATA - PROC_DATA | 9, 0, 0 |
| LROUGH_RAMP_ANGLE | Lathe rough ramp angle | OP_DATA - PROC_DATA | 9, 0, 0 |
| LROUGH_RAPID_STEP | Lathe rough rapid step value | PROC_DATA | 9, 0, 0 |
| LROUGH_RETRACT | Lathe rough retract option | PROC_DATA | 9, 0, 0 |
| LROUGH_ROUGH_START | Lathe rough start option | PROC_DATA | 9, 3, 9 |
| LROUGH_ROUGH_TYPE | Lathe rough cycle type | PROC_DATA | 9, 0, 0 |
| LROUGH_ROUND_CORNERS | Lathe rough round corners option | OP_DATA - PROC_DATA | 9, 0, 0 |
| LROUGH_SFPM | Lathe rough surface speed | PROC_DATA | 9, 3, 9 |
| LROUGH_SHIFT_CUT_WIDTH | Lathe rough shift cut width | PROC_DATA | 9, 0, 0 |
| LROUGH_SHIFT_SQUARE_CORNERS | Lathe rough shift square corners | PROC_DATA | 9, 5, 13 |
| LROUGH_SPINDLE_DIR | Lathe rough spindle direction | OP_DATA - PROC_DATA | 9, 0, 0 |
| LROUGH_START | Lathe rough start option | OP_DATA | 9, 0, 0 |
| LROUGH_START_SIDE_EXT | Lathe rough start side extension amount | PROC_DATA | 9, 5, 13 |
| LROUGH_STOCK | Lathe rough stock value | PROC_DATA | 9, 3, 9 |
| LROUGH_STOCK_X | Lathe rough X stock value | PROC_DATA | 9, 3, 9 |
| LROUGH_STOCK_Z | Lathe rough Z stock value | PROC_DATA | 9, 3, 9 |
| LROUGH_TURN_CUT_WIDTH | Lathe rough turn cut width | PROC_DATA | 9, 0, 0 |
| LROUGH_USE_DEFLECT_COMP | Lathe rough uses deflection compensation | PROC_DATA | 9, 4, 12 |
| LROUGH_XMINUS | Lathe rough cuts in X minus direction | OP_DATA - PROC_DATA | 9, 0, 0 |
| LROUGH_XPLUS | Lathe rough cuts in X plus direction | OP_DATA - PROC_DATA | 9, 0, 0 |
| LROUGH_ZMINUS | Lathe rough cuts in Z minus direction | OP_DATA - PROC_DATA | 9, 0, 0 |
| LROUGH_ZPLUS | Lathe rough cuts in Z plus direction | OP_DATA - PROC_DATA | 9, 0, 0 |
| LTHREAD_ALTERNATE | Lathe thread alternate cut option | OP_DATA - PROC_DATA | 9, 0, 0 |
| LTHREAD_ANGLE | Lathe thread angle | OP_DATA | 9, 0, 0 |
| LTHREAD_ANGLE_ALT | Lathe thread alternate angle | OP_DATA | 9, 0, 0 |
| LTHREAD_BALANCED | Lathe thread balance option | OP_DATA | 9, 0, 0 |
| LTHREAD_BALANCED_IN_FEED | Lathe thread balanced in feed amount | PROC_DATA | 9, 3, 9 |
| LTHREAD_CSS | Lathe thread surface speed value | PROC_DATA | 9, 3, 9 |
| LTHREAD_CUT_DEPTH | Lathe thread cut depth | PROC_DATA | 9, 0, 0 |
| LTHREAD_CUT_DIR | Lathe thread cut direction | PROC_DATA | 9, 3, 9 |
| LTHREAD_CUT_TYPE | Lathe thread cut type (1=one finish pass, 2=constant cut, 3=constant load) | PROC_DATA | 9, 3, 9 |
| LTHREAD_FIRST_CUT | Lathe thread first cut option | OP_DATA | 9, 0, 0 |
| LTHREAD_HEIGHT_XR | Lathe thread height as a radial value | OP_DATA | 9, 0, 0 |
| LTHREAD_LAST_CUT | Lathe thread last cut option | OP_DATA - PROC_DATA | 9, 0, 0 |
| LTHREAD_MAJOR_DIA | Lathe thread major diameter | OP_DATA - PROC_DATA | 9, 0, 0 |
| LTHREAD_MAX_RPM | Lathe thread maximum spindle speed | PROC_DATA | 9, 0, 0 |
| LTHREAD_MINOR_DIA | Lathe thread minor diameter | PROC_DATA | 9, 0, 0 |
| LTHREAD_MINOR_XD | Lathe thread minor diameter | OP_DATA | 9, 0, 0 |
| LTHREAD_NOM_PITCH_INDEX | Lathe thread nominal pitch index | OP_DATA | 9, 0, 0 |
| LTHREAD_NOMINAL | Lathe thread nominal value | OP_DATA | 9, 0, 0 |
| LTHREAD_NOMINAL_PITCH_INDEX | Lathe thread nominal pitch index | PROC_DATA | 9, 3, 9 |
| LTHREAD_NOMINAL_XD | Lathe thread nominal diameter | PROC_DATA | 9, 0, 0 |
| LTHREAD_NUM_SPRING_PASSES | Lathe thread number of spring passes | PROC_DATA | 9, 3, 9 |
| LTHREAD_NUM_STARTS | Lathe thread number of starts | PROC_DATA | 9, 3, 9 |
| LTHREAD_PITCH | Lathe thread pitch | OP_DATA - PROC_DATA | 9, 0, 0 |
| LTHREAD_RUN_IN | Lathe thread run in amount | OP_DATA | 9, 0, 0 |
| LTHREAD_RUN_OUT | Lathe thread run out amount | OP_DATA | 9, 0, 0 |
| LTHREAD_SFPM | Lathe thread surface speed value | PROC_DATA | 9, 0, 0 |
| LTHREAD_SLOPE | Lathe thread slope value | OP_DATA | 9, 0, 0 |
| LTHREAD_STARTS | Lathe thread number of starts | OP_DATA | 9, 0, 0 |
| LTHREAD_STYPE | Lathe thread type | OP_DATA - PROC_DATA | 9, 0, 0 |
| LTHREAD_TAPER | Lathe thread taper value | PROC_DATA | 9, 0, 0 |
| LTHREAD_TAPER_INDEX | Lathe thread taper index | PROC_DATA | 9, 3, 9 |
| LTHREAD_THREAD_ANGLE | Lathe thread thread angle | PROC_DATA | 9, 0, 0 |
| LTHREAD_THREAD_HEIGHT | Lathe thread thread height | PROC_DATA | 9, 0, 0 |
| LTHREAD_TPI | Lathe thread number of TPI | OP_DATA | 9, 0, 0 |
| LTHREAD_TYPE | Lathe thread type | OP_DATA | 9, 0, 0 |
| LTHREAD_X_END_EXTEND | Lathe thread X end extension | PROC_DATA | 9, 0, 0 |
| LTHREAD_X_START_EXTEND | Lathe thread X start extension | PROC_DATA | 9, 0, 0 |
| LTHREAD_Z_END | Lathe thread Z end position | OP_DATA - PROC_DATA | 9, 0, 0 |
| LTHREAD_Z_END_EXTEND | Lathe thread Z end extension | PROC_DATA | 9, 0, 0 |
| LTHREAD_Z_START | Lathe thread Z start position | OP_DATA - PROC_DATA | 9, 0, 0 |
| LTHREAD_Z_START_EXTEND | Lathe thread Z start extension | PROC_DATA | 9, 0, 0 |
| LTOOL_B_AXIS | Lathe tool B axis angle | TOOL_DATA | 9, 0, 0 |
| LTOOL_CUT_SIDE | Lathe tool cut side | TOOL_DATA | 9, 0, 0 |
| LTOOL_DIA_RELIEF | Lathe tool diameter relief | TOOL_DATA | 9, 0, 0 |
| LTOOL_FACE_ANGLE | Lathe tool face angle | TOOL_DATA | 9, 0, 0 |
| LTOOL_FACE_RELIEF | face relief | TOOL_DATA | 9, 0, 0 |
| LTOOL_FACE_UP | Lathe tool face up option | TOOL_DATA | 9, 0, 0 |
| LTOOL_HOLDER | Lathe tool holder type: 0 = other, 1 = holder, 2 = boring bar, 4 = none (if applicable), 5 = ATC, 11 = custom profile, 12 = custom solid | TOOL_DATA | 9, 0, 0 |
| LTOOL_HOLDER_THICKNESS | Lathe tool holder thickness | TOOL_DATA | 9, 0, 0 |
| LTOOL_INSERT_ANGLE | Lathe tool insert angle | TOOL_DATA | 9, 0, 0 |
| LTOOL_ISIZE | Lathe tool insert size | TOOL_DATA | 9, 0, 0 |
| LTOOL_LENGTH | Lathe tool length | TOOL_DATA | 9, 0, 0 |
| LTOOL_MID_ANGLE | Lathe tool mid angle | TOOL_DATA | 9, 0, 0 |
| LTOOL_OFFSET | Lathe tool offset number | TOOL_DATA | 9, 0, 0 |
| LTOOL_ORIENTATION | Lathe tool orientation | TOOL_DATA | 9, 0, 0 |
| LTOOL_OTHER | Lathe tool other data | TOOL_DATA | 9, 0, 0 |
| LTOOL_PRESET_PT_X | Lathe tool preset point in X | TOOL_DATA | 9, 0, 0 |
| LTOOL_PRESET_PT_Z | Lathe tool preset point in Z | TOOL_DATA | 9, 0, 0 |
| LTOOL_SIDE_ANGLE | Lathe tool side angle | TOOL_DATA | 9, 0, 0 |
| LTOOL_SIZE | Lathe tool size | TOOL_DATA | 9, 0, 0 |
| LTOOL_THREAD_DIR | Lathe thread tool direction | TOOL_DATA | 9, 0, 0 |
| LTOOL_THREAD_EDGE_POS_X | Lathe thread tool edge position in X | TOOL_DATA | 9, 0, 0 |
| LTOOL_THREAD_EDGE_POS_Z | Lathe thread tool edge position in Z | TOOL_DATA | 9, 0, 0 |
| LTOOL_THREAD_FLAT_LEN | Lathe thread tool flat length | TOOL_DATA | 9, 0, 0 |
| LTOOL_THREAD_ID_OD | Lathe thread tool ID or OD setting | TOOL_DATA | 9, 0, 0 |
| LTOOL_THREAD_INSERT_WIDTH | Lathe thread tool insert width | TOOL_DATA | 9, 0, 0 |
| LTOOL_THREAD_PITCH | Lathe thread tool pitch | TOOL_DATA | 9, 0, 0 |
| LTOOL_THREAD_STYLE | Lathe thread tool style | TOOL_DATA | 9, 0, 0 |
| LTOOL_THREAD_TYPE | Lathe thread tool type | TOOL_DATA | 9, 0, 0 |
| LTOOL_TIP_ANGLE | Lathe tool tip angle | TOOL_DATA | 9, 0, 0 |
| LTOOL_TIP_CENTER_TO_PRESET_X | Lathe tool tip center to preset pt dist in X | TOOL_DATA | 9, 0, 0 |
| LTOOL_TIP_CENTER_TO_PRESET_Z | Lathe tool tip center to preset pt dist in Z | TOOL_DATA | 9, 0, 0 |
| LTOOL_TIP_OFFSET | Lathe tool tip offset | TOOL_DATA | 9, 0, 0 |
| LTOOL_TIP_RAD | Lathe tool tip radius | TOOL_DATA | 9, 0, 0 |
| LTOOL_TIP_WIDTH | Lathe tool tip width | TOOL_DATA | 9, 0, 0 |
| LTOOL_TURRET_SHIFT_X | Lathe tool turret shift in X | TOOL_DATA | 9, 0, 0 |
| LTOOL_TURRET_SHIFT_Z | Lathe tool turret shift in Z | TOOL_DATA | 9, 0, 0 |
| LTOOL_TYPE | Lathe tool type | TOOL_DATA | 9, 0, 0 |
| LTOOL_UTIL_ANGLE | Lathe utility tool angle | TOOL_DATA | 9, 0, 0 |
| LTOOL_UTIL_DIA | Lathe utility tool diameter | TOOL_DATA | 9, 0, 0 |
| LTOOL_UTIL_LEN | Lathe utility tool length | TOOL_DATA | 9, 0, 0 |
| LTOOL_WIDTH | Lathe tool width | TOOL_DATA | 9, 0, 0 |
| M_USE_ADV_TOL | Use advanced tolerance | OP_DATA - PROC_DATA | 9, 0, 0 |
| M_ZSHIFT | Z shift (Z stock) value | OP_DATA | 9, 0, 0 |
| MACH_ENGINE | Machining engine | OP_DATA | 9, 0, 0 |
| MACH_FLOWS | Number of flows | PART_DATA | 9, 0, 0 |
| MACHINE_MODE | Machine mode | UTIL_PROC_DATA | 9, 0, 0 |
| MATERIAL | Material type | TOOL_DATA | 9, 0, 0 |
| MATERIAL_ONLY | Use material only option | OP_DATA - PROC_DATA | 9, 0, 0 |
| MATERIAL_ONLY_CLEARANCE | Material only clearance | OP_DATA | 9, 0, 0 |
| MD_FROM_TOOL | Multi-depth from tool | OP_DATA - PROC_DATA | 9, 0, 0 |
| MD_PROCESS_LOAD_H1Z_FEAT | Multi-depth H1 feature value | PROC_DATA | 9, 3, 9 |
| MD_RETRACT_LEVEL | Multi-depth retract level | OP_DATA - PROC_DATA | 9, 0, 0 |
| MD_VARY_WITH_FEAT | Multi-depth vary with feature | OP_DATA - PROC_DATA | 9, 0, 0 |
| MD_VARY_WITH_GEO | Multi-depth vary with geometry | OP_DATA - PROC_DATA | 9, 0, 0 |
| MDD_FILE | MDD filename | PART_DATA | 9, 0, 0 |
| MDD_NAME | MDD name | PART_DATA | 9, 0, 0 |
| METRIC_OUTPUT | Uses metric output | SET_POST_DATA | 9, 0, 0 |
| MFIXTURE_TOL | Mill fixture tolerance | OP_DATA - PROC_DATA | 9, 0, 0 |
| MILL_TYPE | Mill process type | PROC_DATA | 9, 0, 0 |
| MILL_TYPE | Mill operation type | OP_DATA | 9, 0, 0 |
| MIN_CUT | Minimum cut | OP_DATA - PROC_DATA | 9, 0, 0 |
| MIN_RAD | Minimum radius | OP_DATA - PROC_DATA | 9, 0, 0 |
| MINIMIZE | Minimize block numbers | SET_POST_DATA | 9, 0, 0 |
| MSTOCK_TOL | Stock tolerance | PROC_DATA | 9, 0, 0 |
| MSURF_CLEAR | Surface clearance | OP_DATA - PROC_DATA | 9, 0, 0 |
| MSURF_STOCK_TOL | Surface stock tolerance | OP_DATA | 9, 0, 0 |
| MSURFACE_CLEAR | Surface clearance | PROC_DATA | 9, 0, 0 |
| MTHREAD_CLEAR_DIA | Thread mill clear diameter | OP_DATA - PROC_DATA | 9, 0, 0 |
| MTHREAD_CUT_DIA | Thread mill cut diameter | OP_DATA - PROC_DATA | 9, 0, 0 |
| MTHREAD_END_THREAD | Thread mill end thread value | OP_DATA - PROC_DATA | 9, 0, 0 |
| MTHREAD_FEED | Thread mill feedrate | OP_DATA - PROC_DATA | 9, 0, 0 |
| MTHREAD_ID_OD | Thread mill ID or OD option | OP_DATA - PROC_DATA | 9, 0, 0 |
| MTHREAD_PITCH | Thread mill pitch | OP_DATA - PROC_DATA | 9, 0, 0 |
| MTHREAD_RAPID_IN | Thread mill rapid in option | PROC_DATA | 9, 0, 0 |
| MTHREAD_START_THREAD | Thread mill start thread | OP_DATA - PROC_DATA | 9, 0, 0 |
| MTHREAD_THREAD_DIR | Thread mill thread direction | OP_DATA - PROC_DATA | 9, 0, 0 |
| MTHREAD_TRAVERSE_CP1 | Thread mill traverse at CP1 | OP_DATA - PROC_DATA | 9, 0, 0 |
| MTOOL_BOTTOM_RAD | Mill tool bottom radius | TOOL_DATA | 9, 0, 0 |
| MTOOL_CORNER_RAD | Mill tool corner radius | TOOL_DATA | 9, 0, 0 |
| MTOOL_FLUTE_LENGTH | Mill tool flute length | TOOL_DATA | 9, 0, 0 |
| MTOOL_INNER_TOP_CORNER_RAD | Mill tool inner top corner radius | TOOL_DATA | 9, 0, 0 |
| MTOOL_LEAD_TIP | Mill tool lead tip value | TOOL_DATA | 9, 0, 0 |
| MTOOL_LEN_OFFSET | Mill tool length offset number | TOOL_DATA | 9, 0, 0 |
| MTOOL_LENGTH | Mill tool length | TOOL_DATA | 9, 0, 0 |
| MTOOL_NON_CUT_DIA | Non cutting diameter | TOOL_DATA | 9, 0, 0 |
| MTOOL_NUM_FLUTES | Mill tool number of flutes | TOOL_DATA | 9, 0, 0 |
| MTOOL_OPTIONS | Mill tool options is checked | TOOL_DATA | 9, 0, 0 |
| MTOOL_ORIENTATION | Mill tool orientation | TOOL_DATA | 9, 0, 0 |
| MTOOL_OUT_OF_HOLDER_LEN | Mill tool out of holder length | TOOL_DATA | 9, 4, 24 |
| MTOOL_PITCH_TPI | Mill tool pitch | TOOL_DATA | 9, 0, 0 |
| MTOOL_PRESET_X | Mill tool preset point in X | TOOL_DATA | 9, 0, 0 |
| MTOOL_PRESET_Y | Mill tool preset point in X | TOOL_DATA | 9, 0, 0 |
| MTOOL_PRESET_Z | Mill tool preset point in Z | TOOL_DATA | 9, 0, 0 |
| MTOOL_RADIUS | Mill tool radius | TOOL_DATA | 9, 0, 0 |
| MTOOL_SHANK_RAD | Mill tool shank radius | TOOL_DATA | 9, 0, 0 |
| MTOOL_TC_SHIFT_X | Mill tool TC shift in X | TOOL_DATA | 9, 0, 0 |
| MTOOL_TC_SHIFT_Y | Mill tool TC shift in Y | TOOL_DATA | 9, 0, 0 |
| MTOOL_TC_SHIFT_Z | Mill tool TC shift in Z | TOOL_DATA | 9, 0, 0 |
| MTOOL_TIP_ANGLE | Mill tool tip angle | TOOL_DATA | 9, 0, 0 |
| MTOOL_TIP_RAD | Mill tool tip radius | TOOL_DATA | 9, 0, 0 |
| MTOOL_TOP_CORNER_RAD | Mill tool top corner radius | TOOL_DATA | 9, 0, 0 |
| MTOOL_TOP_RAD | Mill tool top radius | TOOL_DATA | 9, 0, 0 |
| MTOOL_TYPE | Mill tool type | TOOL_DATA | 9, 0, 0 |
| MZSHIFT | Z shift amount | PROC_DATA | 9, 0, 0 |
| NUM_FLOWS | Total number of flows | PART_DATA | 9, 0, 0 |
| NUM_PARTS | Total number of parts | SET_POST_DATA | 9, 0, 0 |
| NUM_REPEATS | Number of repeats | OP_DATA | 9, 0, 0 |
| NUM_SPINDLES | Total number of spindles | PART_DATA | 9, 0, 0 |
| NUM_SPRING_PASSES | Number of spring passes | OP_DATA | 9, 0, 0 |
| NUM_TOOL_GROUPS | Total number of tool groups | PART_DATA | 9, 0, 0 |
| OD_ID_FACE | OD ID Face setting | OP_DATA | 9, 0, 0 |
| OFFSET | Offset number | TOOL_DATA | 9, 0, 0 |
| ONE_PART_ALL_TOOLS | One part all tools option | SET_POST_DATA | 9, 0, 0 |
| OP_END | Op end text | OP_DATA | 9, 0, 0 |
| OP_START | Op start text | OP_DATA | 9, 0, 0 |
| OP_STOPS | Optional stops setting | SET_POST_DATA | 9, 0, 0 |
| OPEN_CLEARANCE | Open clearance value | OP_DATA - PROC_DATA | 9, 0, 0 |
| ORIENTATION | Orientation | UTIL_PROC_DATA | 9, 0, 0 |
| OUTPUT_FILE | Output filename | SET_POST_DATA | 9, 0, 0 |
| OVERHANG | Overhang amount | OP_DATA - PROC_DATA | 9, 0, 0 |
| OVERLAP | Overlap amount | OP_DATA - PROC_DATA | 9, 0, 0 |
| PART_FILE | Part filename | PART_DATA | 9, 0, 0 |
| PART_IN_MAIN | Part is in main spindle | UTIL_PROC_DATA | 9, 0, 0 |
| PART_IN_SUB | Part is in sub spindle | UTIL_PROC_DATA | 9, 0, 0 |
| PART_NAME | Part name | PART_DATA | 9, 0, 0 |
| PART_SPACING_X | Part spacing in X | SET_POST_DATA | 9, 0, 0 |
| PART_SPACING_Y | Part spacing in Y | SET_POST_DATA | 9, 0, 0 |
| PART_SPACING_Z | Part spacing in Z | SET_POST_DATA | 9, 0, 0 |
| PAST_STOCK | Past stock amount | OP_DATA - PROC_DATA | 9, 0, 0 |
| PATH_CS | Toolpath CS number | OP_DATA - PROC_DATA | 9, 0, 0 |
| PATTERN_INDEX | Pattern index | OP_DATA - PROC_DATA | 9, 3, 9 |
| PATTERN_ON | Pattern on setting | OP_DATA - PROC_DATA | 9, 3, 9 |
| POCKET_ENTRY_HELIX_ANGLE | Pocket entry helix angle | OP_DATA - PROC_DATA | 9, 0, 0 |
| POCKET_ENTRY_HELIX_CP_X | Pocket entry helix X center | OP_DATA - PROC_DATA | 9, 0, 0 |
| POCKET_ENTRY_HELIX_CP_Y | Pocket entry helix Y center | OP_DATA - PROC_DATA | 9, 0, 0 |
| POCKET_ENTRY_HELIX_DIA | Pocket entry helix diameter | OP_DATA - PROC_DATA | 9, 0, 0 |
| POCKET_ENTRY_HELIX_MAX_CUT | Pocket entry maximum cut | OP_DATA - PROC_DATA | 9, 0, 0 |
| POCKET_ENTRY_HELIX_SLOPE | Pocket entry slope | OP_DATA - PROC_DATA | 9, 0, 0 |
| POCKET_ENTRY_HELIX_START_Z | Pocket entry start Z | OP_DATA - PROC_DATA | 9, 0, 0 |
| POCKET_ENTRY_HELIX_TYPE | Pocket entry helix type | OP_DATA - PROC_DATA | 9, 0, 0 |
| POCKET_ENTRY_HELIX_WALL_CLEAR | Pocket entry wall clearance | OP_DATA - PROC_DATA | 9, 0, 0 |
| POCKET_ENTRY_PERIPH_SLOPE | Pocket entry periphery slope | OP_DATA - PROC_DATA | 9, 0, 0 |
| POCKET_ENTRY_PERIPH_START_Z | Pocket entry periphery start Z position | OP_DATA - PROC_DATA | 9, 0, 0 |
| POCKET_ENTRY_PLUNGE_PT_X | Pocket entry plunge point in X | PROC_DATA | 9, 0, 0 |
| POCKET_ENTRY_PLUNGE_PT_Y | Pocket entry plunge point in Y | PROC_DATA | 9, 0, 0 |
| POCKET_ENTRY_RAMP | Pocket entry uses ramp | OP_DATA | 9, 0, 0 |
| POCKET_ENTRY_RAMP_ANGLE | Pocket entry ramp angle | OP_DATA - PROC_DATA | 9, 0, 0 |
| POCKET_ENTRY_RAMP_MAX_CUT | Pocket entry ramp maximum cut | OP_DATA | 9, 0, 0 |
| POCKET_ENTRY_RAMP_SLOPE | Pocket entry ramp slope | OP_DATA - PROC_DATA | 9, 0, 0 |
| POCKET_ENTRY_RAMP_START_Z | Pocket entry ramp start Z position | OP_DATA - PROC_DATA | 9, 0, 0 |
| POCKET_ENTRY_RAMP_TYPE | Pocket entry ramp type | PROC_DATA | 9, 3, 9 |
| POCKET_ENTRY_RAMP_WALL_CLEAR | Pocket entry ramp wall clearance | OP_DATA - PROC_DATA | 9, 0, 0 |
| POCKET_TYPE | Pocket type | OP_DATA - PROC_DATA | 9, 0, 0 |
| POST_FILE | Post filename | SET_POST_DATA | 9, 0, 0 |
| PREF_FOOTER_CHARS | Footer in characters preference | SET_POST_DATA | 9, 0, 0 |
| PREF_FOOTER_FEET | Footer in feet preference | SET_POST_DATA | 9, 0, 0 |
| PREF_FOOTER_METERS | Footer in meters preference | SET_POST_DATA | 9, 0, 0 |
| PREF_FOOTER_METRES | Footer in metres preference | SET_POST_DATA | 9, 0, 0 |
| PREF_HEADER_ABS_INC | Header ABS INC preference | SET_POST_DATA | 9, 0, 0 |
| PREF_HEADER_DATE_TIME | header time preference | SET_POST_DATA | 9, 0, 0 |
| PREF_HEADER_FORMAT_CODE | Header format code preference | SET_POST_DATA | 9, 0, 0 |
| PREF_HEADER_FORMAT_NAME | Header format name preference | SET_POST_DATA | 9, 0, 0 |
| PREF_HEADER_NUM_PARTS | Header number of parts preference | SET_POST_DATA | 9, 0, 0 |
| PREF_HEADER_PROG_COMMENT | Header progam comment preference | SET_POST_DATA | 9, 0, 0 |
| PREF_HEADER_PROG_NAME | header pogram name preference | SET_POST_DATA | 9, 0, 0 |
| PREF_HEADER_SPECIAL | Header special data preference | SET_POST_DATA | 9, 0, 0 |
| PREF_HEADER_START_TOOL | Header start tool preference | SET_POST_DATA | 9, 0, 0 |
| PREF_OP_OP_COMMENT | Op comment option | SET_POST_DATA | 9, 0, 0 |
| PREF_OP_OPNUM_TYPE | Op number type option | SET_POST_DATA | 9, 0, 0 |
| PREF_OP_TOOL_COMMENT | Tool comment option | SET_POST_DATA | 9, 0, 0 |
| PREF_OP_TOOLNUM_TYPE | Tool number type option | SET_POST_DATA | 9, 0, 0 |
| PREF_OP_WG_COMMENT | WorkgGroup comment option | SET_POST_DATA | 9, 0, 0 |
| PREF_SUB | Prefer subs setting | SET_POST_DATA | 9, 0, 0 |
| PREFER_SUBS | Prefer subs setting | PROC_DATA -OP_DATA | 9, 3, 9 |
| PRIME_SPINDLE | Prime spindle number | TOOL_DATA | 9, 0, 0 |
| PROC_GROUP | Process group number | OP_DATA | 9, 0, 0 |
| PROC_ID | Process ID number | OP_DATA | 9, 0, 0 |
| PROC_OP | Process operation number | OP_DATA | 9, 0, 0 |
| PROG_STOP | Program stop option | OP_DATA - PROC_DATA | 9, 3, 9 |
| PULLBACK | Pullback amount | UTIL_PROC_DATA | 9, 0, 0 |
| RADIUS | Part radius | PART_DATA | 9, 0, 0 |
| RAPID_CLEARANCE | Rapid clearance | OP_DATA - PROC_DATA | 9, 0, 0 |
| RAPID_IN | Rapid in | OP_DATA - PROC_DATA | 9, 3, 9 |
| REPEATS | Use repeats | PROC_DATA | 9, 0, 0 |
| RETRACTS | Controls Zig Zag Roughing "No Retracts" flag (inverse sense) | OP_DATA - PROC_DATA | 9, 3, 9 |
| ROUND_CORNERS | Round corners option | OP_DATA - PROC_DATA | 9, 3, 9 |
| RPM | Spindle speed | OP_DATA - PROC_DATA | 9, 0, 0 |
| S_USE_ADV_TOL | Use advanced tolerance | OP_DATA - PROC_DATA | 9, 3, 9 |
| SAME_STROKE | Same stroke option | OP_DATA - PROC_DATA | 9, 3, 9 |
| SCALLOP_FEED | Scallop feed amount | OP_DATA - PROC_DATA | 9, 0, 0 |
| SCALLOP_FEED_LOCK | Scallop feed lock | OP_DATA - PROC_DATA | 9, 3, 9 |
| SELECTED_OPS | Post selected oerations | SET_POST_DATA | 9, 0, 0 |
| SEQ_BY | Block seq by value | SET_POST_DATA | 9, 0, 0 |
| SEQ_FROM | Block seq from value | SET_POST_DATA | 9, 0, 0 |
| SFLOCUT_TYPE | Surface flow cut type | OP_DATA | 9, 0, 0 |
| SFLOW_MACH_DIR | Surface flow machining direction | OP_DATA | 9, 0, 0 |
| SFLOW_MACH_ZORDER | Surface flow machining Z order | OP_DATA | 9, 0, 0 |
| SFLOW_TRAVEL_AROUND_MODE | Surface flow travel around mode | OP_DATA | 9, 0, 0 |
| SHIFT_DISTANCE | Shift distance | UTIL_PROC_DATA | 9, 0, 0 |
| SPIN_CONTROL | Spindle control option | OP_DATA | 9, 0, 0 |
| SPINDLE_DIR | Spindle direction | TOOL_DATA | 9, 0, 0 |
| SPINDLE_NUM | Spindle number | UTIL_PROC_DATA | 9, 0, 0 |
| SPINDLE_ON | Spindle is on | UTIL_PROC_DATA | 9, 0, 0 |
| SPINDLE_SPEED | Spindle speed | UTIL_PROC_DATA | 9, 0, 0 |
| SPINDLE_UNLOADED | Spindle is unloaded | UTIL_PROC_DATA | 9, 0, 0 |
| SPINDLE_USED | Spindle is used | SET_POST_DATA | 9, 0, 0 |
| START_ON_RIGHT | Start on right | OP_DATA - PROC_DATA | 9, 0, 0 |
| START_PROG_NUM | Start program number | SET_POST_DATA | 9, 0, 0 |
| STAY_CLEAR | Stay clear option | OP_DATA - PROC_DATA | 9, 3, 9 |
| STEP | Step value | OP_DATA | 9, 0, 0 |
| STEPOVER_FEED | Stepover feed value | OP_DATA - PROC_DATA | 9, 0, 0 |
| STEPOVER_FEED_LOCK | Stepover feed lock | OP_DATA - PROC_DATA | 9, 3, 9 |
| STOCK | Stock amount (Pocket stock, for Mill Offset Roughing) | OP_DATA - PROC_DATA | 9, 3, 9 |
| STOCK_DIA | Stock diameter | SET_POST_DATA | 9, 0, 0 |
| STOCK_RAD | Stock radius | PART_DATA - SET_POST_DATA | 9, 0, 0 |
| STOCK_X1 | Stock X1 position | PART_DATA | 9, 0, 0 |
| STOCK_X2 | Stock X2 position | PART_DATA | 9, 0, 0 |
| STOCK_Y1 | Stock Y1 position | PART_DATA | 9, 0, 0 |
| STOCK_Y2 | Stock Y2 position | PART_DATA | 9, 0, 0 |
| STOCK_Z1 | Stock X1 position | PART_DATA - POST_DATA | 9, 0, 0 |
| STOCK_Z2 | Stock Z2 position | PART_DATA - POST_DATA | 9, 0, 0 |
| SUB_IN_UNLOAD | Sub spindle in unload | UTIL_PROC_DATA | 9, 0, 0 |
| SURF_STOCK | Surface stock | OP_DATA | 9, 0, 0 |
| SURF_Z | Surface Z value | PROC_DATA | 9, 3, 9 |
| SURFACE_ARC_FIT_TOL | Surface arc fit tolerance | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_BACK_AND_FORTH | Surface back and forth option | PROC_DATA | 9, 0, 0 |
| SURFACE_BACK_FORTH | Surface back and forth option | OP_DATA | 9, 0, 0 |
| SURFACE_CFEED | Surface contour feedrate | PROC_DATA | 9, 3, 9 |
| SURFACE_CLEANUP_TYPE | Surface cleanup type | PROC_DATA | 9, 4, 12 |
| SURFACE_CLEAR_STOCK | Surface clear stock amount | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_CLEAR_STOCK_TYPE | Surface clear stock type | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_CONST_FACES_CLEAR | Surface constant faces clear value | PROC_DATA | 9, 3, 9 |
| SURFACE_CONSTRAIN | Surface constraint amount | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_CONSTRAINT_FACES_CLEAR | Surface constraint faces clear option | OP_DATA | 9, 0, 0 |
| SURFACE_CONSTRAINT_TOL | Surface constraint tolerance | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_CORNER_RAD | Surface corner radius | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_CURVE_CUT_DIR | Surface curve cut direction | OP_DATA | 9, 0, 0 |
| SURFACE_CUT_ANGLE | Surface cut angle | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_CUT_OPT | Surface cut option | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_CUT_OVER_EDGES | Surface cut over edges | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_CUT_TOL | Surface cut tolerance | PROC_DATA | 9, 3, 9 |
| SURFACE_CUT_TYPE | Surface cut type | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_CUTS_TYPE | Surface cuts type | PROC_DATA | 9, 0, 0 |
| SURFACE_DEPTH | Surface depth of cut | OP_DATA | 9, 0, 0 |
| SURFACE_DESIRED_Z | Surface desired Z depth | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_EFEED | Surface entry feedrate | PROC_DATA | 9, 3, 9 |
| SURFACE_ENTRY_PLUNGE_PT_X | Surface entry plunge point in X | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_ENTRY_PLUNGE_PT_Y | Surface entry plunge point in Y | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_ENTRY_RAMP_TYPE | Surface entry ramp type | OP_DATA - PROC_DATA | 9, 3, 9 |
| SURFACE_ENTRY_TYPE | Surface entry type | OP_DATA - PROC_DATA | 9, 3, 9 |
| SURFACE_FIXTURE_CLEAR | Surface fixture clearance | PROC_DATA | 9, 3, 9 |
| SURFACE_FIXTURE_TOL | Surface fixture tolerance | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_FLOW_CUT_TYPE | Surface flow cut direction | PROC_DATA | 9, 0, 0 |
| SURFACE_FLOW_MACH_DIR | Surface flow machining direction | PROC_DATA | 9, 0, 0 |
| SURFACE_FLOW_MACH_Z_ORDER | Surface flow machining Z order | PROC_DATA | 9, 0, 0 |
| SURFACE_FLOW_TRAVEL_AROUND_MODE | Surface flow travel around mode | PROC_DATA | 9, 0, 0 |
| SURFACE_INTERSECT_TYPE | Surface intersection type | PROC_DATA | 9, 0, 0 |
| SURFACE_LACE_CUT_DIR | Surface lace cut direction | PROC_DATA - OP_DATA | 9, 0, 0 |
| SURFACE_MAX_CUT_ANGLE | Surface maximum cut angle | OP_DATA - PROC_DATA | 9, 3, 9 |
| SURFACE_NORMAL_ANGLE | Surface normal angle | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_OFFSET_SURFACES | Surface offset surfaces option | PROC_DATA | 9, 0, 0 |
| SURFACE_OFFSET_SURFS | Surface offset surfaces option | OP_DATA | 9, 0, 0 |
| SURFACE_ONE_PASS | Surface one pass option | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_OUTPUT_PREF | Surface output preference | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_PASSES_PER_SIDE | Surface number of passes per side | PROC_DATA | 9, 0, 0 |
| SURFACE_PASSES_TYPE | Surface pass type | PROC_DATA | 9, 0, 0 |
| SURFACE_RETRACT_OPT | Surface retract option | OP_DATA | 9, 0, 0 |
| SURFACE_RETRACT_OPTION | Surface retract option | PROC_DATA | 9, 0, 0 |
| SURFACE_RIDGE_HEIGHT | Surface ridge height | PROC_DATA - OP_DATA | 9, 3, 9 |
| SURFACE_SKIP_FLATS | Surface skip flats option | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_SMOOTH_TOL | Surface smoothing tolerance | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_SPLINE_APPROX_TOL | Surface spline approximation tolerance | PROC_DATA | 9, 3, 9 |
| SURFACE_SPLINE_TOL | Surface spline tolerance | OP_DATA | 9, 0, 0 |
| SURFACE_STAY_IN_STOCK | Surface stay in stock option | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_STEP_CUT_RATIO | Surface stepover cut ration | PROC_DATA -OP_DATA | 9, 3, 9 |
| SURFACE_STEP_OVER | Surface stepover | OP_DATA | 9, 0, 0 |
| SURFACE_STEPOVER | Surface stepover | PROC_DATA | 9, 3, 9 |
| SURFACE_STOCK | Surface stock amount | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_STOCK_TOL | Surface stock tolerance | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_TYPE | Surface type | OP_DATA - PROC_DATA | 9, 0, 0 |
| SURFACE_Z | Surface Z value | PROC_DATA | 9, 3, 9 |
| SURFACE_DEPTH | Surface depth | OP_DATA | 9, 0, 0 |
| TG_COUNT | Total number of ToolGroups | PART_DATA | 9, 0, 0 |
| TIME | Time | OP_DATA - PROC_DATA | 9, 0, 0 |
| TIP_Z | Tip Z position | PROC_DATA | 9, 3, 9 |
| TO_WORKPIECE | To workpiece option | UTIL_PROC_DATA | 9, 0, 0 |
| TOOL_CHANGE | Toolchange option | PROC_DATA | 9, 0, 0 |
| TOOL_CHANGE_X | Toolchange position in X | PART_DATA - GET_TG_DATA | 9, 0, 0 |
| TOOL_CHANGE_Y | Toolchange position in Y | PART_DATA - GET_TG_DATA | 9, 0, 0 |
| TOOL_CHANGE_Z | Toolchange position in Z | PART_DATA - GET_TG_DATA | 9, 0, 0 |
| TOOL_GROUP | ToolGroup number | OP_DATA - PROC_DATA | 9, 0, 0 |
| TOOL_GROUP_POS | ToolGroup position | TOOL_DATA | 9, 0, 0 |
| TOOL_NEG_SIDE | Negative side option | TOOL_DATA | 9, 0, 0 |
| TOOL_NUM | Tool number | OP_DATA - PROC_DATA | 9, 0, 0 |
| TOOLGROUP | ToolGroup number | TOOL_DATA | 9, 0, 0 |
| TORQUE_SENSING | Torque sensing option | UTIL_PROC_DATA | 9, 0, 0 |
| TORQUE_VAL | Torque value | UTIL_PROC_DATA | 9, 0, 0 |
| TYPE | Tool type | TOOL_DATA | 9, 0, 0 |
| TYPE | Operation type | OP_DATA | 9, 0, 0 |
| TYPE | Process type | PROC_DATA | 9, 0, 0 |
| TYPE | Part type | PART_DATA | 9, 0, 0 |
| UNITS | Part units | PART_DATA | 9, 0, 0 |
| USE_ID | Tool uses ID | TOOL_DATA | 9, 0, 0 |
| UTIL_TYPE | Utility type | OP_DATA | 9, 0, 0 |
| WALL_ANG | Wall angle | OP_DATA | 9, 0, 0 |
| WALL_ANGLE | Wall angle | PROC_DATA | 9, 0, 0 |
| WALL_BOT | Wall bottom value | OP_DATA | 9, 0, 0 |
| WALL_BOTTOM | Wall bottom value | PROC_DATA | 9, 0, 0 |
| WALL_DCEP_SIDE | Wall DCEP side value | OP_DATA | 9, 0, 0 |
| WALL_IANG | Internal wall angle | OP_DATA | 9, 0, 0 |
| WALL_IBOT | Internal wall bottom | OP_DATA | 9, 0, 0 |
| WALL_ITOP | Internal wall top | OP_DATA | 9, 0, 0 |
| WALL_MODE | Wall mode | OP_DATA - PROC_DATA | 9, 0, 0 |
| WALL_RIDGE_HEIGHT | Wall ridge height | OP_DATA - PROC_DATA | 9, 0, 0 |
| WALL_SAME_DCEP_SIDE | Wall same side DCEP | PROC_DATA | 9, 3, 9 |
| WALL_SAME_DIR | Wall same direction option | OP_DATA - PROC_DATA | 9, 0, 0 |
| WALL_SHAPE_STEP | Wall uses shape step | OP_DATA - PROC_DATA | 9, 0, 0 |
| WALL_STEP | Wall step amount | OP_DATA - PROC_DATA | 9, 0, 0 |
| WALL_SWEPT_ISLAND | Wall uses swept islands | OP_DATA - PROC_DATA | 9, 0, 0 |
| WALL_SWEPT_POCKET | Wall uses swept pockets | OP_DATA - PROC_DATA | 9, 0, 0 |
| WALL_TOP | Wall top | OP_DATA - PROC_DATA | 9, 0, 0 |
| WALL_TOP_TO_BOTTOM | Wall cut from top to bottom | OP_DATA - PROC_DATA | 9, 3, 9 |
| WALL_USER_STEP | Wall user step amount | OP_DATA - PROC_DATA | 9, 0, 0 |
| WALLI_ANGLE | Internal wall angle | PROC_DATA | 9, 0, 0 |
| WALLI_BOTTOM | Internal wall bottom | PROC_DATA | 9, 0, 0 |
| WALLI_TOP | Internal wall top | PROC_DATA | 9, 0, 0 |
| WG_NUM | WorkGroup number | OP_DATA | 9, 0, 0 |
| WORK_FIXTURES | Use work fixtures | SET_POST_DATA | 9, 0, 0 |
| WORKPIECE | Workpiece number | OP_DATA | 9, 0, 0 |
| WP_COUNT | Workpiece count | PART_DATA | 9, 0, 0 |
| WRAP | Wrap option | OP_DATA - PROC_DATA | 9, 3, 9 |
| WRAP_COPY_ANGLE | Wrap duplication angle | PROC_DATA | 9, 0, 0 |
| WRAP_DUP_ANGLE | Wrap duplication angle | OP_DATA | 9, 0, 0 |
| WRAP_DUPS | Wrap number of duplications | OP_DATA | 9, 0, 0 |
| WRAP_NUM_COPIES | Wrap number of duplications | PROC_DATA | 9, 3, 9 |
| WRAP_START_ANGLE | Wrap start angle | OP_DATA - PROC_DATA | 9, 0, 0 |
| X_CLEARANCE | X clearance value | UTIL_PROC_DATA | 9, 0, 0 |
| X_DROP | X drop value | UTIL_PROC_DATA | 9, 0, 0 |
| X_HOME | X home option | UTIL_PROC_DATA | 9, 0, 0 |
| X_POSITION | X position value | UTIL_PROC_DATA | 9, 0, 0 |
| X_VALUE | X value | UTIL_PROC_DATA | 9, 0, 0 |
| Z_CLEARANCE | Z clearance value | UTIL_PROC_DATA | 9, 0, 0 |
| Z_DROP | Z drop value | UTIL_PROC_DATA | 9, 0, 0 |
| Z_HOME | Z home option | UTIL_PROC_DATA | 9, 0, 0 |
| Z_POSITION | Z postition | UTIL_PROC_DATA | 9, 0, 0 |
| Z_STEP | Actual Z stepover | OP_DATA - PROC_DATA | 9, 0, 0 |
| Z_STEP_WANTED | Z stepover desired | OP_DATA - PROC_DATA | 9, 3, 9 |
| Z_VALUE | Z value | UTIL_PROC_DATA | 9, 0, 0 |
| ZIG_ZAG | Zigzag option | OP_DATA | 9, 0, 0 |
