All Variables
From Macros Wiki
| These variables are set by some of the macro commands | Set by | Version Number |
| Button | Number of button pressed on macro dialog. ( OK button = zero ) | 9, 4, 25 |
| CircleRef | Number of circle created by a circle geometry command | 9, 4, 25 |
| ContourRef | Number of contour created by a contour geometry command | 9, 4, 25 |
| CsNumber | Number of CS created by the NEW_CS command | 9, 4, 25 |
| CURRENT_CS_NUM | Variable set automatically by the system when a coordinate system is selected or created | 9, 0, 0 |
| CURRENT_WG_NUM | Variable set automatically by the system when a workgroup is selected or created | 9, 0, 0 |
| ExcelCellLength | Variable set automatically by the system when using the EXCEL_FIND_CELL command | 9, 4, 25 |
| ExcelError | Error code set by all Excel commands | 9, 4, 25 |
| EXCEL_IS_OPEN | Variable set automatically by the system dictating whether or not an excel file is open | 9, 0, 0 |
| EXCEL_IS_VISIBLE | Variable set automatically by the system dictating whether or not an excel file is visible | 9, 0, 0 |
| FEAT_TYPE_ARC | Variable set automatically by the system about a feature type | 9, 0, 0 |
| FEAT_TYPE_CTOOL | Variable set automatically by the system about a feature type | 9, 0, 0 |
| FEAT_TYPE_CURVE | Variable set automatically by the system about a feature type | 9, 0, 0 |
| FEAT_TYPE_LINE_IJK | Variable set automatically by the system about a feature type | 9, 0, 0 |
| FEAT_TYPE_LINE | Variable set automatically by the system about a feature type | 9, 0, 0 |
| FEAT_TYPE_MARKER | Variable set automatically by the system about a feature type | 9, 0, 0 |
| FEAT_TYPE_POINT | Variable set automatically by the system about a feature type | 9, 0, 0 |
| FEAT_TYPE_RAPID | Variable set automatically by the system about a feature type | 9, 0, 0 |
| FEAT_TYPE_SPLINE | Variable set automatically by the system about a feature type | 9, 0, 0 |
| FileError | Error code set by all file commands | 9, 4, 25 |
| GIBBSCAM_VERSION_1 | Variable set automatically by the system dictating the version of gibbscam running | 9, 4, 24 |
| GIBBSCAM_VERSION_2 | Variable set automatically by the system dictating the version of gibbscam running | 9, 4, 24 |
| GIBBSCAM_VERSION_3 | Variable set automatically by the system dictating the version of gibbscam running | 9, 4, 24 |
| GIBBSCAM_WINDOW_X1 | Variable set automatically by the system dictating the first x position of the gibbscam window | 9, 0, 0 |
| GIBBSCAM_WINDOW_X2 | Variable set automatically by the system dictating the second x position of the gibbscam window | 9, 0, 0 |
| GIBBSCAM_WINDOW_Y1 | Variable set automatically by the system dictating the first y position of the gibbscam window | 9, 0, 0 |
| GIBBSCAM_WINDOW_Y2 | Variable set automatically by the system dictating the second y position of the gibbscam window | 9, 0, 0 |
| HoleFrAngle | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrBottom | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrBottomClear | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrBottomZ | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrCS | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrDepth | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrDia | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrDiaTop | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrError | Error code set by all HOLEFR commands | 9, 4, 25 |
| HoleFrFullDepth | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrMidDepth | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrPosAxisX | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrPosAxisY | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrPosAxisZ | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrPosTopX | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrPosTopY | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrPosTopZ | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrPosX | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrPosY | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrPosZ | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrRef | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrRevCS | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrThroughType | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrtipAngle | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrTop | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrTopClear | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrTopZ | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrType | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrWidth | Variable set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| LineRef | Number of line created by a line geometry command | 9, 4, 25 |
| MTOOL_HOLDER | Variable set automatically reporting the mill tool holder | 9, 0, 0 |
| MTOOL_HOLDER_TYPE | Variable set automatically reporting the mill tool holder type | 9, 4, 24 |
| MTOOL_HOLDER_TYPE_BORE | Variable set automatically reporting if the mill tool holder is bore | 9, 4, 24 |
| MTOOL_HOLDER_TYPE_COLLET | Variable set automatically reporting if the mill tool holder is a collet | 9, 4, 24 |
| MTOOL_HOLDER_TYPE_DRILL | Variable set automatically reporting if the mill tool holder is a drill | 9, 4, 24 |
| MTOOL_HOLDER_TYPE_MILL | Variable set automatically reporting if the mill tool holder is a mill | 9, 4, 24 |
| MTOOL_HOLDER_TYPE_ROT_CLAMP | Variable set automatically reporting if the mill tool holder is a rotary clamp | 9, 4, 24 |
| MTOOL_HOLDER_TYPE_SHELL | Variable set automatically reporting if the mill tool holder is a shell | 9, 4, 24 |
| MTOOL_HOLDER_TYPE_SHRINK_FIT | Variable set automatically reporting if the mill tool holder is a shrink fit | 9, 4, 24 |
| MTOOL_HOLDER_TYPE_TAP | Variable set automatically reporting if the mill tool holder is a tap | 9, 4, 24 |
| MTOOL_HOLDER_TYPE_TG_COLLET | Variable set automatically reporting if the mill tool holder is a tool group | 9, 4, 24 |
| PLUGIN_VERSION_1 | Variable set automatically by the system dictating the version of plugin running | 9, 4, 24 |
| PLUGIN_VERSION_2 | Variable set automatically by the system dictating the version of plugin running | 9, 4, 24 |
| PLUGIN_VERSION_3 | Variable set automatically by the system dictating the version of plugin running | 9, 4, 24 |
| PointRef | Number of point created by a point geometry command | 9, 4, 25 |
| ReadVarsNumVars | Number of variables read using READ_NUM_VARS command | 9, 4, 25 |
| SCREEN_HEIGHT | Variable set automatically by the system dictating the height of the screen | 9, 0, 0 |
| SCREEN_WIDTH | Variable set automatically by the system dictating the height of the screen | 9, 0, 0 |
| SolidRef | Number of solid created by an EXTRUDE_SHAPE command | 9, 4, 25 |
| TOOL_ORIENT_DL | Variable set automatically reporting if the tool orientation is down left | 9, 4, 24 |
| TOOL_ORIENT_DOWN_LEFT | Variable set automatically reporting if the tool orientation is down left | 9, 4, 24 |
| TOOL_ORIENT_DOWN_RIGHT | Variable set automatically reporting if the tool orientation is down right | 9, 4, 24 |
| TOOL_ORIENT_DR | Variable set automatically reporting if the tool orientation is down right | 9, 4, 24 |
| TOOL_ORIENT_LD | Variable set automatically reporting if the tool orientation is left down | 9, 4, 24 |
| TOOL_ORIENT_LEFT_DOWN | Variable set automatically reporting if the tool orientation is left down | 9, 4, 24 |
| TOOL_ORIENT_LEFT_UP | Variable set automatically reporting if the tool orientation is left up | 9, 4, 24 |
| TOOL_ORIENT_LU | Variable set automatically reporting if the tool orientation is left up | 9, 4, 24 |
| TOOL_ORIENT_RD | Variable set automatically reporting if the tool orientation is right down | 9, 4, 24 |
| TOOL_ORIENT_RIGHT_DOWN | Variable set automatically reporting if the tool orientation is right down | 9, 4, 24 |
| TOOL_ORIENT_RIGHT_UP | Variable set automatically reporting if the tool orientation is right up | 9, 4, 24 |
| TOOL_ORIENT_RU | Variable set automatically reporting if the tool orientation is right up | 9, 4, 24 |
| TOOL_ORIENT_UL | Variable set automatically reporting if the tool orientation is up left | 9, 4, 24 |
| TOOL_ORIENT_UP_LEFT | Variable set automatically reporting if the tool orientation is up left | 9, 4, 24 |
| TOOL_ORIENT_UP_RIGHT | Variable set automatically reporting if the tool orientation is up right | 9, 4, 24 |
| TOOL_ORIENT_UR | Variable set automatically reporting if the tool orientation is up right | 9, 4, 24 |
| TOOL_TYPE_35_DEG | Variable set automatically reporting if the tool type is 35 degrees | 9, 4, 24 |
| TOOL_TYPE_55_DEG | Variable set automatically reporting if the tool type is 55 degrees | 9, 4, 24 |
| TOOL_TYPE_55_PARA | Variable set automatically reporting if the tool type is 55 parallel | 9, 4, 24 |
| TOOL_TYPE_80_DEG | Variable set automatically reporting if the tool type is 80 degrees | 9, 4, 24 |
| TOOL_TYPE_BACK_BORE | Variable set automatically reporting if the tool type is back bore | 9, 0, 0 |
| TOOL_TYPE_BALL_END_MILL | Variable set automatically reporting if the tool type is a ball end mill | 9, 0, 0 |
| TOOL_TYPE_BORE | Variable set automatically reporting if the tool type is bore | 9, 0, 0 |
| TOOL_TYPE_CENTER_DRILL | Variable set automatically reporting if the tool type is a center drill | 9, 0, 0 |
| TOOL_TYPE_COUNTERSINK | Variable set automatically reporting if the tool type is a countersink | 9, 0, 0 |
| TOOL_TYPE_CUTOFF | Variable set automatically reporting if the tool type is cutoff | 9, 4, 24 |
| TOOL_TYPE_DRILL | Variable set automatically reporting if the tool type is a drill | 9, 0, 0 |
| TOOL_TYPE_FACE_CUTTER | Variable set automatically reporting if the tool type is a face cutter | 9, 0, 0 |
| TOOL_TYPE_FINISH_END_MILL | Variable set automatically reporting if the tool type is a finish end mill | 9, 0, 0 |
| TOOL_TYPE_FLY_CUTTER | Variable set automatically reporting if the tool type is a fly cutter | 9, 0, 0 |
| TOOL_TYPE_FORM | Variable set automatically reporting if the tool type is form | 9, 4, 24 |
| TOOL_TYPE_GROOVE | Variable set automatically reporting if the tool type is groove | 9, 4, 24 |
| TOOL_TYPE_KEY_CUTTER | Variable set automatically reporting if the tool type is a key cutter | 9, 0, 0 |
| TOOL_TYPE_PENTAGON | Variable set automatically reporting if the tool type is pentagon | 9, 4, 24 |
| TOOL_TYPE_REAMER | Variable set automatically reporting if the tool type is a reamer | 9, 0, 0 |
| TOOL_TYPE_RECTANGLE | Variable set automatically reporting if the tool type is a rectangle | 9, 4, 24 |
| TOOL_TYPE_RIGID_TAP | Variable set automatically reporting if the tool type is a rigid tap | 9, 0, 0 |
| TOOL_TYPE_ROUGH_END_MILL | Variable set automatically reporting if the tool type is an end mill | 9, 0, 0 |
| TOOL_TYPE_ROUND | Variable set automatically reporting if the tool type is a round | 9, 4, 24 |
| TOOL_TYPE_ROUNDOVER | Variable set automatically reporting if the tool type is a roundover | 9, 0, 0 |
| TOOL_TYPE_SHELL_CUTTER | Variable set automatically reporting if the tool type is a shellcutter | 9, 0, 0 |
| TOOL_TYPE_SPOT_DRILL | Variable set automatically reporting if the tool type is a spot drill | 9, 0, 0 |
| TOOL_TYPE_SPOT_FACE | Variable set automatically reporting if the tool type is a spot face | 9, 0, 0 |
| TOOL_TYPE_SQUARE | Variable set automatically reporting if the tool type is a square | 9, 4, 24 |
| TOOL_TYPE_TAP | Variable set automatically reporting if the tool type is a tap | 9, 0, 0 |
| TOOL_TYPE_THREAD_MILL | Variable set automatically reporting if the tool type is a thread mill | 9, 0, 0 |
| TOOL_TYPE_THREAD1 | Variable set automatically reporting if the tool type is a thread | 9, 4, 24 |
| TOOL_TYPE_THREAD2 | Variable set automatically reporting if the tool type is a thread | 9, 4, 24 |
| TOOL_TYPE_TRIANGLE | Variable set automatically reporting if the tool type is a triangle | 9, 4, 24 |
| TOOL_TYPE_TRIGON | Variable set automatically reporting if the tool type is trigonometrical | 9, 4, 24 |
| TOOL_TYPE_UTIL | Variable set automatically reporting if the tool type is utility | 9, 4, 24 |
| TOOL_TYPE_VPROFILE | Variable set automatically reporting if the tool type is vprofile | 9, 0, 0 |
| WgNumber | Number of WorkGroup created by the NEW_WG command | 9, 4, 25 |
