All Variables: Difference between revisions

From Macros Wiki
Jump to navigationJump to search
← Older editNewer edit →
ConnerO (talk | contribs)
GibbsDevs
5,024 edits
No edit summary
ConnerO (talk | contribs)
GibbsDevs
5,024 edits
No edit summary
Line 11: Line 11:
| align=“left” |CsNumber || Number of CS created by the [[NEW_CS]] command ||9, 4, 25
| align=“left” |CsNumber || Number of CS created by the [[NEW_CS]] command ||9, 4, 25
|-
|-
| align="left" |CURRENT_CS_NUM|| Number set automatically by the system when a coordinate system is selected or created || 9, 0, 0
| align="left" |CURRENT_CS_NUM|| Variable set automatically by the system when a coordinate system is selected or created || 9, 0, 0
|-
|-
| align="left" |CURRENT_WG_NUM||Number set automatically by the system when a workgroup is selected or created || 9, 0, 0
| align="left" |CURRENT_WG_NUM||Variable set automatically by the system when a workgroup is selected or created || 9, 0, 0
|-
|-
| align=“left” |ExcelCellLength || Number set automatically by the system when using the [[EXCEL_FIND_CELL]] command ||9, 4, 25
| align=“left” |ExcelCellLength || Variable set automatically by the system when using the [[EXCEL_FIND_CELL]] command ||9, 4, 25
|-
|-
| align=“left” |ExcelError || Error code set by all [[:Category:Excel|Excel]] commands ||9, 4, 25
| align=“left” |ExcelError || Error code set by all [[:Category:Excel|Excel]] commands ||9, 4, 25
|-
|-
| align="left" |EXCEL_IS_OPEN||Number set automatically by the system dictating whether or not an excel file is open || 9, 0, 0
| align="left" |EXCEL_IS_OPEN||Variable set automatically by the system dictating whether or not an excel file is open || 9, 0, 0
|-
|-
| align="left" |EXCEL_IS_VISIBLE||Number set automatically by the system dictating whether or not an excel file is visible|| 9, 0, 0
| align="left" |EXCEL_IS_VISIBLE||Variable set automatically by the system dictating whether or not an excel file is visible|| 9, 0, 0
|-
|-
| align="left" |FEAT_TYPE_ARC|| Number set automatically by the system about a feature type||9, 0, 0
| align="left" |FEAT_TYPE_ARC|| Variable set automatically by the system about a feature type||9, 0, 0
|-
|-
| align="left" |FEAT_TYPE_CTOOL|| Number set automatically by the system about a feature type ||9, 0, 0
| align="left" |FEAT_TYPE_CTOOL|| Variable set automatically by the system about a feature type ||9, 0, 0
|-
|-
| align="left" |FEAT_TYPE_CURVE|| Number set automatically by the system about a feature type ||9, 0, 0
| align="left" |FEAT_TYPE_CURVE|| Variable set automatically by the system about a feature type ||9, 0, 0
|-
|-
| align="left" |FEAT_TYPE_LINE_IJK|| Number set automatically by the system about a feature type ||9, 0, 0
| align="left" |FEAT_TYPE_LINE_IJK|| Variable set automatically by the system about a feature type ||9, 0, 0
|-
|-
| align="left" |FEAT_TYPE_LINE|| Number set automatically by the system about a feature type ||9, 0, 0
| align="left" |FEAT_TYPE_LINE|| Variable set automatically by the system about a feature type ||9, 0, 0
|-
|-
| align="left" |FEAT_TYPE_MARKER|| Number set automatically by the system about a feature type ||9, 0, 0
| align="left" |FEAT_TYPE_MARKER|| Variable set automatically by the system about a feature type ||9, 0, 0
|-
|-
| align="left" |FEAT_TYPE_POINT|| Number set automatically by the system about a feature type ||9, 0, 0
| align="left" |FEAT_TYPE_POINT|| Variable set automatically by the system about a feature type ||9, 0, 0
|-
|-
| align="left" |FEAT_TYPE_RAPID|| Number set automatically by the system about a feature type ||9, 0, 0
| align="left" |FEAT_TYPE_RAPID|| Variable set automatically by the system about a feature type ||9, 0, 0
|-
|-
| align="left" |FEAT_TYPE_SPLINE|| Number set automatically by the system about a feature type ||9, 0, 0
| align="left" |FEAT_TYPE_SPLINE|| Variable set automatically by the system about a feature type ||9, 0, 0
|-
|-
| align=“left” |FileError || Error code set by all file commands ||9, 4, 25
| align=“left” |FileError || Error code set by all file commands ||9, 4, 25
|-
|-
| align="left" |GIBBSCAM_VERSION_1||Number set automatically by the system dictating the version of gibbscam is running|| 9, 4, 24
| align="left" |GIBBSCAM_VERSION_1||Variable set automatically by the system dictating the version of gibbscam running|| 9, 4, 24
|-
|-
| align="left" |GIBBSCAM_VERSION_2||Number set automatically by the system dictating the version of gibbscam is running || 9, 4, 24
| align="left" |GIBBSCAM_VERSION_2||Variable set automatically by the system dictating the version of gibbscam running || 9, 4, 24
|-
|-
| align="left" |GIBBSCAM_VERSION_3||Number set automatically by the system dictating the version of gibbscam is running || 9, 4, 24
| align="left" |GIBBSCAM_VERSION_3||Variable set automatically by the system dictating the version of gibbscam running || 9, 4, 24
|-
|-
| align="left" |GIBBSCAM_WINDOW_X1||Number set automatically by the system dictating the first x position of the gibbscam window || 9, 0, 0
| align="left" |GIBBSCAM_WINDOW_X1||Variable set automatically by the system dictating the first x position of the gibbscam window || 9, 0, 0
|-
|-
| align="left" |GIBBSCAM_WINDOW_X2||Number set automatically by the system dictating the second x position of the gibbscam window || 9, 0, 0
| align="left" |GIBBSCAM_WINDOW_X2||Variable set automatically by the system dictating the second x position of the gibbscam window || 9, 0, 0
|-
|-
| align="left" |GIBBSCAM_WINDOW_Y1||Number set automatically by the system dictating the first y position of the gibbscam window || 9, 0, 0
| align="left" |GIBBSCAM_WINDOW_Y1||Variable set automatically by the system dictating the first y position of the gibbscam window || 9, 0, 0
|-
|-
| align="left" |GIBBSCAM_WINDOW_Y2||Number set automatically by the system dictating the second y position of the gibbscam window || 9, 0, 0
| align="left" |GIBBSCAM_WINDOW_Y2||Variable set automatically by the system dictating the second y position of the gibbscam window || 9, 0, 0
|-
|-
| align=“left” |HoleFrAngle ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrAngle ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrBottom ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrBottom ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrBottomClear ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrBottomClear ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrBottomZ ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrBottomZ ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrCS ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrCS ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrDepth ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrDepth ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrDia ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrDia ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrDiaTop ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrDiaTop ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrError || Error code set by all [[:Category:Hole_Manager|HOLEFR]] commands ||9, 4, 25
| align=“left” |HoleFrError || Error code set by all [[:Category:Hole_Manager|HOLEFR]] commands ||9, 4, 25
|-
|-
| align=“left” |HoleFrFullDepth ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrFullDepth ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrMidDepth ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrMidDepth ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrPosAxisX ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrPosAxisX ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrPosAxisY ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrPosAxisY ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrPosAxisZ ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrPosAxisZ ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrPosTopX ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrPosTopX ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrPosTopY ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrPosTopY ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrPosTopZ ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrPosTopZ ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrPosX ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrPosX ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrPosY ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrPosY ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrPosZ ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrPosZ ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrRef ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrRef ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrRevCS ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrRevCS ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrThroughType ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrThroughType ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrtipAngle ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrtipAngle ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrTop ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrTop ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrTopClear ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrTopClear ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrTopZ ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrTopZ ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrType ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrType ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |HoleFrWidth ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
| align=“left” |HoleFrWidth ||Variable set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25
|-
|-
| align=“left” |LineRef || Number of line created by a line [[:Geometry:Creating_Geometry|geometry]] command||9, 4, 25
| align=“left” |LineRef || Number of line created by a line [[:Geometry:Creating_Geometry|geometry]] command||9, 4, 25
|-
|-
| align="left" |MTOOL_HOLDER ||   || 9, 0, 0
| align="left" |MTOOL_HOLDER || Variable set automatically reporting the mill tool holder || 9, 0, 0
|-
|-
| align="left" |MTOOL_HOLDER_TYPE ||   || 9, 4, 24
| align="left" |MTOOL_HOLDER_TYPE || Variable set automatically reporting the mill tool holder type || 9, 4, 24
|-
|-
| align="left" |MTOOL_HOLDER_TYPE_BORE||   ||9, 4, 24
| align="left" |MTOOL_HOLDER_TYPE_BORE|| Variable set automatically reporting if the mill tool holder is bore ||9, 4, 24
|-
|-
| align="left" |MTOOL_HOLDER_TYPE_COLLET||   ||9, 4, 24
| align="left" |MTOOL_HOLDER_TYPE_COLLET|| Variable set automatically reporting if the mill tool holder is a collet ||9, 4, 24
|-
|-
| align="left" |MTOOL_HOLDER_TYPE_DRILL||   ||9, 4, 24
| align="left" |MTOOL_HOLDER_TYPE_DRILL|| Variable set automatically reporting if the mill tool holder is a drill ||9, 4, 24
|-
|-
| align="left" |MTOOL_HOLDER_TYPE_MILL||   ||9, 4, 24
| align="left" |MTOOL_HOLDER_TYPE_MILL|| Variable set automatically reporting if the mill tool holder is a mill ||9, 4, 24
|-
|-
| align="left" |MTOOL_HOLDER_TYPE_ROT_CLAMP||   ||9, 4, 24
| align="left" |MTOOL_HOLDER_TYPE_ROT_CLAMP|| Variable set automatically reporting if the mill tool holder is a rotary clamp ||9, 4, 24
|-
|-
| align="left" |MTOOL_HOLDER_TYPE_SHELL||   ||9, 4, 24
| align="left" |MTOOL_HOLDER_TYPE_SHELL|| Variable set automatically reporting if the mill tool holder is a shell ||9, 4, 24
|-
|-
| align="left" |MTOOL_HOLDER_TYPE_SHRINK_FIT||   ||9, 4, 24
| align="left" |MTOOL_HOLDER_TYPE_SHRINK_FIT|| Variable set automatically reporting if the mill tool holder is a shrink fit ||9, 4, 24
|-
|-
| align="left" |MTOOL_HOLDER_TYPE_TAP||   ||9, 4, 24
| align="left" |MTOOL_HOLDER_TYPE_TAP|| Variable set automatically reporting if the mill tool holder is a tap ||9, 4, 24
|-
|-
| align="left" |MTOOL_HOLDER_TYPE_TG_COLLET||   ||9, 4, 24
| align="left" |MTOOL_HOLDER_TYPE_TG_COLLET|| Variable set automatically reporting if the mill tool holder is a tool group ||9, 4, 24
|-
|-
| align="left" |PLUGIN_VERSION_1||  || 9, 4, 24
| align="left" |PLUGIN_VERSION_1||Variable set automatically by the system dictating the version of plugin running || 9, 4, 24
|-
|-
| align="left" |PLUGIN_VERSION_2||  || 9, 4, 24
| align="left" |PLUGIN_VERSION_2||Variable set automatically by the system dictating the version of plugin running || 9, 4, 24
|-
|-
| align="left" |PLUGIN_VERSION_3||  || 9, 4, 24
| align="left" |PLUGIN_VERSION_3||Variable set automatically by the system dictating the version of plugin running || 9, 4, 24
|-
|-
| align=“left” |PointRef || Number of point created by a point [[:Geometry:Creating_Geometry|geometry]] command||9, 4, 25
| align=“left” |PointRef || Number of point created by a point [[:Geometry:Creating_Geometry|geometry]] command||9, 4, 25
Line 149: Line 149:
| align=“left” |ReadVarsNumVars || Number of variables read using READ_NUM_VARS command ||9, 4, 25
| align=“left” |ReadVarsNumVars || Number of variables read using READ_NUM_VARS command ||9, 4, 25
|-
|-
| align="left" |SCREEN_HEIGHT||  || 9, 0, 0
| align="left" |SCREEN_HEIGHT||Variable set automatically by the system dictating the height of the screen|| 9, 0, 0
|-
|-
| align="left" |SCREEN_WIDTH||  ||9, 0, 0
| align="left" |SCREEN_WIDTH||Variable set automatically by the system dictating the height of the screen ||9, 0, 0
|-
|-
| align=“left” |SolidRef || Number of solid created by an [[EXTRUDE_SHAPE]] command||9, 4, 25
| align=“left” |SolidRef || Number of solid created by an [[EXTRUDE_SHAPE]] command||9, 4, 25
|-
|-
| align="left" |TOOL_ORIENT_DL||   ||9, 4, 24
| align="left" |TOOL_ORIENT_DL|| Variable set automatically reporting if the tool orientation is down left ||9, 4, 24
|-
|-
| align="left" |TOOL_ORIENT_DOWN_LEFT||   ||9, 4, 24
| align="left" |TOOL_ORIENT_DOWN_LEFT|| Variable set automatically reporting if the tool orientation is down left ||9, 4, 24
|-
|-
| align="left" |TOOL_ORIENT_DOWN_RIGHT||   ||9, 4, 24
| align="left" |TOOL_ORIENT_DOWN_RIGHT|| Variable set automatically reporting if the tool orientation is down right ||9, 4, 24
|-
|-
| align="left" |TOOL_ORIENT_DOWN_RIGHT||   ||9, 4, 24
| align="left" |TOOL_ORIENT_DR|| Variable set automatically reporting if the tool orientation is down right ||9, 4, 24
|-
|-
| align="left" |TOOL_ORIENT_DR||   ||9, 4, 24
| align="left" |TOOL_ORIENT_LD|| Variable set automatically reporting if the tool orientation is left down ||9, 4, 24
|-
|-
| align="left" |TOOL_ORIENT_LD||   ||9, 4, 24
| align="left" |TOOL_ORIENT_LEFT_DOWN|| Variable set automatically reporting if the tool orientation is left down ||9, 4, 24
|-
|-
| align="left" |TOOL_ORIENT_LEFT_DOWN||   ||9, 4, 24
| align="left" |TOOL_ORIENT_LEFT_UP|| Variable set automatically reporting if the tool orientation is left up ||9, 4, 24
|-
|-
| align="left" |TOOL_ORIENT_LEFT_UP||   ||9, 4, 24
| align="left" |TOOL_ORIENT_LU|| Variable set automatically reporting if the tool orientation is left up ||9, 4, 24
|-
|-
| align="left" |TOOL_ORIENT_LU||   ||9, 4, 24
| align="left" |TOOL_ORIENT_RD|| Variable set automatically reporting if the tool orientation is right down ||9, 4, 24
|-
|-
| align="left" |TOOL_ORIENT_RD||   ||9, 4, 24
| align="left" |TOOL_ORIENT_RIGHT_DOWN|| Variable set automatically reporting if the tool orientation is right down ||9, 4, 24
|-
|-
| align="left" |TOOL_ORIENT_RIGHT_DOWN||   ||9, 4, 24
| align="left" |TOOL_ORIENT_RIGHT_UP|| Variable set automatically reporting if the tool orientation is right up ||9, 4, 24
|-
|-
| align="left" |TOOL_ORIENT_RIGHT_UP||   ||9, 4, 24
| align="left" |TOOL_ORIENT_RU|| Variable set automatically reporting if the tool orientation is right up ||9, 4, 24
|-
|-
| align="left" |TOOL_ORIENT_RU||   ||9, 4, 24
| align="left" |TOOL_ORIENT_UL|| Variable set automatically reporting if the tool orientation is up left ||9, 4, 24
|-
|-
| align="left" |TOOL_ORIENT_UL||   ||9, 4, 24
| align="left" |TOOL_ORIENT_UP_LEFT|| Variable set automatically reporting if the tool orientation is up left ||9, 4, 24
|-
|-
| align="left" |TOOL_ORIENT_UP_LEFT||   ||9, 4, 24
| align="left" |TOOL_ORIENT_UP_RIGHT|| Variable set automatically reporting if the tool orientation is up right ||9, 4, 24
|-
|-
| align="left" |TOOL_ORIENT_UP_RIGHT||   ||9, 4, 24
| align="left" |TOOL_ORIENT_UR|| Variable set automatically reporting if the tool orientation is up right ||9, 4, 24
|-
|-
| align="left" |TOOL_ORIENT_UR||   ||9, 4, 24
| align="left" |TOOL_TYPE_35_DEG ||Variable set automatically reporting if the tool type is 35 degrees || 9, 4, 24
|-
|-
| align="left" |TOOL_TYPE_35_DEG ||   || 9, 4, 24
| align="left" |TOOL_TYPE_55_DEG || Variable set automatically reporting if the tool type is 55 degrees  || 9, 4, 24
|-
|-
| align="left" |TOOL_TYPE_55_DEG ||   || 9, 4, 24
| align="left" |TOOL_TYPE_55_PARA || Variable set automatically reporting if the tool type is 55 parallel || 9, 4, 24
|-
|-
| align="left" |TOOL_TYPE_55_PARA ||   || 9, 4, 24
| align="left" |TOOL_TYPE_80_DEG || Variable set automatically reporting if the tool type is 80 degrees || 9, 4, 24
|-
|-
| align="left" |TOOL_TYPE_80_DEG ||   || 9, 4, 24
| align="left" |TOOL_TYPE_BACK_BORE|| Variable set automatically reporting if the tool type is back bore ||9, 0, 0
|-
|-
| align="left" |TOOL_TYPE_BACK_BORE||   ||9, 0, 0
| align="left" |TOOL_TYPE_BALL_END_MILL|| Variable set automatically reporting if the tool type is a ball end mill ||9, 0, 0
|-
|-
| align="left" |TOOL_TYPE_BALL_END_MILL||   ||9, 0, 0
| align="left" |TOOL_TYPE_BORE|| Variable set automatically reporting if the tool type is bore ||9, 0, 0
|-
|-
| align="left" |TOOL_TYPE_BORE||   ||9, 0, 0
| align="left" |TOOL_TYPE_CENTER_DRILL|| Variable set automatically reporting if the tool type is a center drill ||9, 0, 0
|-
|-
| align="left" |TOOL_TYPE_CENTER_DRILL||   ||9, 0, 0
| align="left" |TOOL_TYPE_COUNTERSINK|| Variable set automatically reporting if the tool type is a countersink ||9, 0, 0
|-
|-
| align="left" |TOOL_TYPE_COUNTERSINK||   ||9, 0, 0
| align="left" |TOOL_TYPE_CUTOFF || Variable set automatically reporting if the tool type is cutoff || 9, 4, 24
|-
|-
| align="left" |TOOL_TYPE_CUTOFF ||   || 9, 4, 24
| align="left" |TOOL_TYPE_DRILL|| Variable set automatically reporting if the tool type is a drill ||9, 0, 0
|-
|-
| align="left" |TOOL_TYPE_DRILL||   ||9, 0, 0
| align="left" |TOOL_TYPE_FACE_CUTTER|| Variable set automatically reporting if the tool type is a face cutter ||9, 0, 0
|-
|-
| align="left" |TOOL_TYPE_FACE_CUTTER||   ||9, 0, 0
| align="left" |TOOL_TYPE_FINISH_END_MILL|| Variable set automatically reporting if the tool type is a finish end mill ||9, 0, 0
|-
|-
| align="left" |TOOL_TYPE_FINISH_END_MILL||   ||9, 0, 0
| align="left" |TOOL_TYPE_FLY_CUTTER|| Variable set automatically reporting if the tool type is a fly cutter || 9, 0, 0
|-
|-
| align="left" |TOOL_TYPE_FLY_CUTTER||   || 9, 0, 0
| align="left" |TOOL_TYPE_FORM || Variable set automatically reporting if the tool type is form || 9, 4, 24
|-
|-
| align="left" |TOOL_TYPE_FORM ||   || 9, 4, 24
| align="left" |TOOL_TYPE_GROOVE || Variable set automatically reporting if the tool type is groove || 9, 4, 24
|-
|-
| align="left" |TOOL_TYPE_GROOVE ||   || 9, 4, 24
| align="left" |TOOL_TYPE_KEY_CUTTER|| Variable set automatically reporting if the tool type is a key cutter || 9, 0, 0
|-
|-
| align="left" |TOOL_TYPE_KEY_CUTTER||   || 9, 0, 0
| align="left" |TOOL_TYPE_PENTAGON || Variable set automatically reporting if the tool type is pentagon ||9, 4, 24
|-
|-
| align="left" |TOOL_TYPE_PENTAGON ||   ||9, 4, 24
| align="left" |TOOL_TYPE_REAMER|| Variable set automatically reporting if the tool type is a reamer ||9, 0, 0
|-
|-
| align="left" |TOOL_TYPE_REAMER||   ||9, 0, 0
| align="left" |TOOL_TYPE_RECTANGLE || Variable set automatically reporting if the tool type is a rectangle || 9, 4, 24
|-
|-
| align="left" |TOOL_TYPE_RECTANGLE ||   || 9, 4, 24
| align="left" |TOOL_TYPE_RIGID_TAP|| Variable set automatically reporting if the tool type is a rigid tap ||9, 0, 0
|-
|-
| align="left" |TOOL_TYPE_RIGID_TAP||   ||9, 0, 0
| align="left" |TOOL_TYPE_ROUGH_END_MILL|| Variable set automatically reporting if the tool type is an end mill || 9, 0, 0
|-
|-
| align="left" |TOOL_TYPE_ROUGH_END_MILL||   || 9, 0, 0
| align="left" |TOOL_TYPE_ROUND || Variable set automatically reporting if the tool type is a round || 9, 4, 24
|-
|-
| align="left" |TOOL_TYPE_ROUND ||   || 9, 4, 24
| align="left" |TOOL_TYPE_ROUNDOVER|| Variable set automatically reporting if the tool type is a roundover ||9, 0, 0
|-
|-
| align="left" |TOOL_TYPE_ROUNDOVER||   ||9, 0, 0
| align="left" |TOOL_TYPE_SHELL_CUTTER|| Variable set automatically reporting if the tool type is a shellcutter ||9, 0, 0
|-
|-
| align="left" |TOOL_TYPE_SHELL_CUTTER||   ||9, 0, 0
| align="left" |TOOL_TYPE_SPOT_DRILL|| Variable set automatically reporting if the tool type is a spot drill ||9, 0, 0
|-
|-
| align="left" |TOOL_TYPE_SPOT_DRILL||   ||9, 0, 0
| align="left" |TOOL_TYPE_SPOT_FACE|| Variable set automatically reporting if the tool type is a spot face ||9, 0, 0
|-
|-
| align="left" |TOOL_TYPE_SPOT_FACE||   ||9, 0, 0
| align="left" |TOOL_TYPE_SQUARE || Variable set automatically reporting if the tool type is a square || 9, 4, 24
|-
|-
| align="left" |TOOL_TYPE_SQUARE ||   || 9, 4, 24
| align="left" |TOOL_TYPE_TAP|| Variable set automatically reporting if the tool type is a tap ||9, 0, 0
|-
|-
| align="left" |TOOL_TYPE_TAP||   ||9, 0, 0
| align="left" |TOOL_TYPE_THREAD_MILL|| Variable set automatically reporting if the tool type is a thread mill ||9, 0, 0
|-
|-
| align="left" |TOOL_TYPE_THREAD_MILL||   ||9, 0, 0
| align="left" |TOOL_TYPE_THREAD1 || Variable set automatically reporting if the tool type is a thread || 9, 4, 24
|-
|-
| align="left" |TOOL_TYPE_THREAD1 ||   || 9, 4, 24
| align="left" |TOOL_TYPE_THREAD2 || Variable set automatically reporting if the tool type is a thread || 9, 4, 24
|-
|-
| align="left" |TOOL_TYPE_THREAD2 ||   || 9, 4, 24
| align="left" |TOOL_TYPE_TRIANGLE || Variable set automatically reporting if the tool type is a triangle || 9, 4, 24
|-
|-
| align="left" |TOOL_TYPE_TRIANGLE ||   || 9, 4, 24
| align="left" |TOOL_TYPE_TRIGON || Variable set automatically reporting if the tool type is trigonometrical || 9, 4, 24
|-
|-
| align="left" |TOOL_TYPE_TRIGON ||   || 9, 4, 24
| align="left" |TOOL_TYPE_UTIL || Variable set automatically reporting if the tool type is utility || 9, 4, 24
|-
|-
| align="left" |TOOL_TYPE_UTIL ||   || 9, 4, 24
| align="left" |TOOL_TYPE_VPROFILE || Variable set automatically reporting if the tool type is vprofile || 9, 0, 0
|-
| align="left" |TOOL_TYPE_VPROFILE ||   || 9, 0, 0
|-
|-
| align=“left” |WgNumber || Number of WorkGroup created by the [[NEW_WG]] command ||9, 4, 25
| align=“left” |WgNumber || Number of WorkGroup created by the [[NEW_WG]] command ||9, 4, 25
|-
|-
|}
|}

Revision as of 23:01, 20 August 2010

These variables are set by some of the macro commands Set by Version Number
Button Number of button pressed on macro dialog. ( OK button = zero ) 9, 4, 25
CircleRef Number of circle created by a circle geometry command 9, 4, 25
ContourRef Number of contour created by a contour geometry command 9, 4, 25
CsNumber Number of CS created by the NEW_CS command 9, 4, 25
CURRENT_CS_NUM Variable set automatically by the system when a coordinate system is selected or created 9, 0, 0
CURRENT_WG_NUM Variable set automatically by the system when a workgroup is selected or created 9, 0, 0
ExcelCellLength Variable set automatically by the system when using the EXCEL_FIND_CELL command 9, 4, 25
ExcelError Error code set by all Excel commands 9, 4, 25
EXCEL_IS_OPEN Variable set automatically by the system dictating whether or not an excel file is open 9, 0, 0
EXCEL_IS_VISIBLE Variable set automatically by the system dictating whether or not an excel file is visible 9, 0, 0
FEAT_TYPE_ARC Variable set automatically by the system about a feature type 9, 0, 0
FEAT_TYPE_CTOOL Variable set automatically by the system about a feature type 9, 0, 0
FEAT_TYPE_CURVE Variable set automatically by the system about a feature type 9, 0, 0
FEAT_TYPE_LINE_IJK Variable set automatically by the system about a feature type 9, 0, 0
FEAT_TYPE_LINE Variable set automatically by the system about a feature type 9, 0, 0
FEAT_TYPE_MARKER Variable set automatically by the system about a feature type 9, 0, 0
FEAT_TYPE_POINT Variable set automatically by the system about a feature type 9, 0, 0
FEAT_TYPE_RAPID Variable set automatically by the system about a feature type 9, 0, 0
FEAT_TYPE_SPLINE Variable set automatically by the system about a feature type 9, 0, 0
FileError Error code set by all file commands 9, 4, 25
GIBBSCAM_VERSION_1 Variable set automatically by the system dictating the version of gibbscam running 9, 4, 24
GIBBSCAM_VERSION_2 Variable set automatically by the system dictating the version of gibbscam running 9, 4, 24
GIBBSCAM_VERSION_3 Variable set automatically by the system dictating the version of gibbscam running 9, 4, 24
GIBBSCAM_WINDOW_X1 Variable set automatically by the system dictating the first x position of the gibbscam window 9, 0, 0
GIBBSCAM_WINDOW_X2 Variable set automatically by the system dictating the second x position of the gibbscam window 9, 0, 0
GIBBSCAM_WINDOW_Y1 Variable set automatically by the system dictating the first y position of the gibbscam window 9, 0, 0
GIBBSCAM_WINDOW_Y2 Variable set automatically by the system dictating the second y position of the gibbscam window 9, 0, 0
HoleFrAngle Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrBottom Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrBottomClear Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrBottomZ Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrCS Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrDepth Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrDia Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrDiaTop Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrError Error code set by all HOLEFR commands 9, 4, 25
HoleFrFullDepth Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrMidDepth Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrPosAxisX Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrPosAxisY Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrPosAxisZ Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrPosTopX Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrPosTopY Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrPosTopZ Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrPosX Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrPosY Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrPosZ Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrRef Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrRevCS Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrThroughType Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrtipAngle Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrTop Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrTopClear Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrTopZ Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrType Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
HoleFrWidth Variable set automatically when using the HOLEFR_GET_FEAT command 9, 4, 25
LineRef Number of line created by a line geometry command 9, 4, 25
MTOOL_HOLDER Variable set automatically reporting the mill tool holder 9, 0, 0
MTOOL_HOLDER_TYPE Variable set automatically reporting the mill tool holder type 9, 4, 24
MTOOL_HOLDER_TYPE_BORE Variable set automatically reporting if the mill tool holder is bore 9, 4, 24
MTOOL_HOLDER_TYPE_COLLET Variable set automatically reporting if the mill tool holder is a collet 9, 4, 24
MTOOL_HOLDER_TYPE_DRILL Variable set automatically reporting if the mill tool holder is a drill 9, 4, 24
MTOOL_HOLDER_TYPE_MILL Variable set automatically reporting if the mill tool holder is a mill 9, 4, 24
MTOOL_HOLDER_TYPE_ROT_CLAMP Variable set automatically reporting if the mill tool holder is a rotary clamp 9, 4, 24
MTOOL_HOLDER_TYPE_SHELL Variable set automatically reporting if the mill tool holder is a shell 9, 4, 24
MTOOL_HOLDER_TYPE_SHRINK_FIT Variable set automatically reporting if the mill tool holder is a shrink fit 9, 4, 24
MTOOL_HOLDER_TYPE_TAP Variable set automatically reporting if the mill tool holder is a tap 9, 4, 24
MTOOL_HOLDER_TYPE_TG_COLLET Variable set automatically reporting if the mill tool holder is a tool group 9, 4, 24
PLUGIN_VERSION_1 Variable set automatically by the system dictating the version of plugin running 9, 4, 24
PLUGIN_VERSION_2 Variable set automatically by the system dictating the version of plugin running 9, 4, 24
PLUGIN_VERSION_3 Variable set automatically by the system dictating the version of plugin running 9, 4, 24
PointRef Number of point created by a point geometry command 9, 4, 25
ReadVarsNumVars Number of variables read using READ_NUM_VARS command 9, 4, 25
SCREEN_HEIGHT Variable set automatically by the system dictating the height of the screen 9, 0, 0
SCREEN_WIDTH Variable set automatically by the system dictating the height of the screen 9, 0, 0
SolidRef Number of solid created by an EXTRUDE_SHAPE command 9, 4, 25
TOOL_ORIENT_DL Variable set automatically reporting if the tool orientation is down left 9, 4, 24
TOOL_ORIENT_DOWN_LEFT Variable set automatically reporting if the tool orientation is down left 9, 4, 24
TOOL_ORIENT_DOWN_RIGHT Variable set automatically reporting if the tool orientation is down right 9, 4, 24
TOOL_ORIENT_DR Variable set automatically reporting if the tool orientation is down right 9, 4, 24
TOOL_ORIENT_LD Variable set automatically reporting if the tool orientation is left down 9, 4, 24
TOOL_ORIENT_LEFT_DOWN Variable set automatically reporting if the tool orientation is left down 9, 4, 24
TOOL_ORIENT_LEFT_UP Variable set automatically reporting if the tool orientation is left up 9, 4, 24
TOOL_ORIENT_LU Variable set automatically reporting if the tool orientation is left up 9, 4, 24
TOOL_ORIENT_RD Variable set automatically reporting if the tool orientation is right down 9, 4, 24
TOOL_ORIENT_RIGHT_DOWN Variable set automatically reporting if the tool orientation is right down 9, 4, 24
TOOL_ORIENT_RIGHT_UP Variable set automatically reporting if the tool orientation is right up 9, 4, 24
TOOL_ORIENT_RU Variable set automatically reporting if the tool orientation is right up 9, 4, 24
TOOL_ORIENT_UL Variable set automatically reporting if the tool orientation is up left 9, 4, 24
TOOL_ORIENT_UP_LEFT Variable set automatically reporting if the tool orientation is up left 9, 4, 24
TOOL_ORIENT_UP_RIGHT Variable set automatically reporting if the tool orientation is up right 9, 4, 24
TOOL_ORIENT_UR Variable set automatically reporting if the tool orientation is up right 9, 4, 24
TOOL_TYPE_35_DEG Variable set automatically reporting if the tool type is 35 degrees 9, 4, 24
TOOL_TYPE_55_DEG Variable set automatically reporting if the tool type is 55 degrees 9, 4, 24
TOOL_TYPE_55_PARA Variable set automatically reporting if the tool type is 55 parallel 9, 4, 24
TOOL_TYPE_80_DEG Variable set automatically reporting if the tool type is 80 degrees 9, 4, 24
TOOL_TYPE_BACK_BORE Variable set automatically reporting if the tool type is back bore 9, 0, 0
TOOL_TYPE_BALL_END_MILL Variable set automatically reporting if the tool type is a ball end mill 9, 0, 0
TOOL_TYPE_BORE Variable set automatically reporting if the tool type is bore 9, 0, 0
TOOL_TYPE_CENTER_DRILL Variable set automatically reporting if the tool type is a center drill 9, 0, 0
TOOL_TYPE_COUNTERSINK Variable set automatically reporting if the tool type is a countersink 9, 0, 0
TOOL_TYPE_CUTOFF Variable set automatically reporting if the tool type is cutoff 9, 4, 24
TOOL_TYPE_DRILL Variable set automatically reporting if the tool type is a drill 9, 0, 0
TOOL_TYPE_FACE_CUTTER Variable set automatically reporting if the tool type is a face cutter 9, 0, 0
TOOL_TYPE_FINISH_END_MILL Variable set automatically reporting if the tool type is a finish end mill 9, 0, 0
TOOL_TYPE_FLY_CUTTER Variable set automatically reporting if the tool type is a fly cutter 9, 0, 0
TOOL_TYPE_FORM Variable set automatically reporting if the tool type is form 9, 4, 24
TOOL_TYPE_GROOVE Variable set automatically reporting if the tool type is groove 9, 4, 24
TOOL_TYPE_KEY_CUTTER Variable set automatically reporting if the tool type is a key cutter 9, 0, 0
TOOL_TYPE_PENTAGON Variable set automatically reporting if the tool type is pentagon 9, 4, 24
TOOL_TYPE_REAMER Variable set automatically reporting if the tool type is a reamer 9, 0, 0
TOOL_TYPE_RECTANGLE Variable set automatically reporting if the tool type is a rectangle 9, 4, 24
TOOL_TYPE_RIGID_TAP Variable set automatically reporting if the tool type is a rigid tap 9, 0, 0
TOOL_TYPE_ROUGH_END_MILL Variable set automatically reporting if the tool type is an end mill 9, 0, 0
TOOL_TYPE_ROUND Variable set automatically reporting if the tool type is a round 9, 4, 24
TOOL_TYPE_ROUNDOVER Variable set automatically reporting if the tool type is a roundover 9, 0, 0
TOOL_TYPE_SHELL_CUTTER Variable set automatically reporting if the tool type is a shellcutter 9, 0, 0
TOOL_TYPE_SPOT_DRILL Variable set automatically reporting if the tool type is a spot drill 9, 0, 0
TOOL_TYPE_SPOT_FACE Variable set automatically reporting if the tool type is a spot face 9, 0, 0
TOOL_TYPE_SQUARE Variable set automatically reporting if the tool type is a square 9, 4, 24
TOOL_TYPE_TAP Variable set automatically reporting if the tool type is a tap 9, 0, 0
TOOL_TYPE_THREAD_MILL Variable set automatically reporting if the tool type is a thread mill 9, 0, 0
TOOL_TYPE_THREAD1 Variable set automatically reporting if the tool type is a thread 9, 4, 24
TOOL_TYPE_THREAD2 Variable set automatically reporting if the tool type is a thread 9, 4, 24
TOOL_TYPE_TRIANGLE Variable set automatically reporting if the tool type is a triangle 9, 4, 24
TOOL_TYPE_TRIGON Variable set automatically reporting if the tool type is trigonometrical 9, 4, 24
TOOL_TYPE_UTIL Variable set automatically reporting if the tool type is utility 9, 4, 24
TOOL_TYPE_VPROFILE Variable set automatically reporting if the tool type is vprofile 9, 0, 0
WgNumber Number of WorkGroup created by the NEW_WG command 9, 4, 25
Retrieved from "https://macros.gibbscam.com/index.php?title=All_Variables&oldid=5436"