All Variables: Difference between revisions
From Macros Wiki
Jump to navigationJump to search
No edit summary |
No edit summary |
||
| Line 19: | Line 19: | ||
| align=“left” |ExcelError || Error code set by all [[:Category:Excel|Excel]] commands ||9, 4, 25 | | align=“left” |ExcelError || Error code set by all [[:Category:Excel|Excel]] commands ||9, 4, 25 | ||
|- | |- | ||
| align="left" |EXCEL_IS_OPEN|| | | align="left" |EXCEL_IS_OPEN||Number set automatically by the system dictating whether or not an excel file is open || 9, 0, 0 | ||
|- | |- | ||
| align="left" |EXCEL_IS_VISIBLE|| | | align="left" |EXCEL_IS_VISIBLE||Number set automatically by the system dictating whether or not an excel file is visible|| 9, 0, 0 | ||
|- | |- | ||
| align="left" |FEAT_TYPE_ARC|| | | align="left" |FEAT_TYPE_ARC|| Number set automatically by the system about a feature type||9, 0, 0 | ||
|- | |- | ||
| align="left" |FEAT_TYPE_CTOOL|| | | align="left" |FEAT_TYPE_CTOOL|| Number set automatically by the system about a feature type ||9, 0, 0 | ||
|- | |- | ||
| align="left" |FEAT_TYPE_CURVE|| | | align="left" |FEAT_TYPE_CURVE|| Number set automatically by the system about a feature type ||9, 0, 0 | ||
|- | |- | ||
| align="left" |FEAT_TYPE_LINE_IJK|| | | align="left" |FEAT_TYPE_LINE_IJK|| Number set automatically by the system about a feature type ||9, 0, 0 | ||
|- | |- | ||
| align="left" |FEAT_TYPE_LINE|| | | align="left" |FEAT_TYPE_LINE|| Number set automatically by the system about a feature type ||9, 0, 0 | ||
|- | |- | ||
| align="left" |FEAT_TYPE_MARKER|| | | align="left" |FEAT_TYPE_MARKER|| Number set automatically by the system about a feature type ||9, 0, 0 | ||
|- | |- | ||
| align="left" |FEAT_TYPE_POINT|| | | align="left" |FEAT_TYPE_POINT|| Number set automatically by the system about a feature type ||9, 0, 0 | ||
|- | |- | ||
| align="left" |FEAT_TYPE_RAPID|| | | align="left" |FEAT_TYPE_RAPID|| Number set automatically by the system about a feature type ||9, 0, 0 | ||
|- | |- | ||
| align="left" |FEAT_TYPE_SPLINE|| | | align="left" |FEAT_TYPE_SPLINE|| Number set automatically by the system about a feature type ||9, 0, 0 | ||
|- | |- | ||
| align=“left” |FileError || Error code set by all file commands ||9, 4, 25 | | align=“left” |FileError || Error code set by all file commands ||9, 4, 25 | ||
|- | |- | ||
| align="left" |GIBBSCAM_VERSION_1|| | | align="left" |GIBBSCAM_VERSION_1||Number set automatically by the system dictating the version of gibbscam is running|| 9, 4, 24 | ||
|- | |- | ||
| align="left" |GIBBSCAM_VERSION_2|| | | align="left" |GIBBSCAM_VERSION_2||Number set automatically by the system dictating the version of gibbscam is running || 9, 4, 24 | ||
|- | |- | ||
| align="left" |GIBBSCAM_VERSION_3|| | | align="left" |GIBBSCAM_VERSION_3||Number set automatically by the system dictating the version of gibbscam is running || 9, 4, 24 | ||
|- | |- | ||
| align="left" |GIBBSCAM_WINDOW_X1|| | | align="left" |GIBBSCAM_WINDOW_X1||Number set automatically by the system dictating the first x position of the gibbscam window || 9, 0, 0 | ||
|- | |- | ||
| align="left" |GIBBSCAM_WINDOW_X2|| | | align="left" |GIBBSCAM_WINDOW_X2||Number set automatically by the system dictating the second x position of the gibbscam window || 9, 0, 0 | ||
|- | |- | ||
| align="left" |GIBBSCAM_WINDOW_Y1|| | | align="left" |GIBBSCAM_WINDOW_Y1||Number set automatically by the system dictating the first y position of the gibbscam window || 9, 0, 0 | ||
|- | |- | ||
| align="left" |GIBBSCAM_WINDOW_Y2|| | | align="left" |GIBBSCAM_WINDOW_Y2||Number set automatically by the system dictating the second y position of the gibbscam window || 9, 0, 0 | ||
|- | |- | ||
| align=“left” |HoleFrAngle || || 9, 4, 25 | | align=“left” |HoleFrAngle ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrBottom || || 9, 4, 25 | | align=“left” |HoleFrBottom ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrBottomClear || || 9, 4, 25 | | align=“left” |HoleFrBottomClear ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrBottomZ || || 9, 4, 25 | | align=“left” |HoleFrBottomZ ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrCS || || 9, 4, 25 | | align=“left” |HoleFrCS ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrDepth || || 9, 4, 25 | | align=“left” |HoleFrDepth ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrDia || || 9, 4, 25 | | align=“left” |HoleFrDia ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrDiaTop || || 9, 4, 25 | | align=“left” |HoleFrDiaTop ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrError || Error code set by all HOLEFR commands ||9, 4, 25 | | align=“left” |HoleFrError || Error code set by all [[:Category:Hole_Manager|HOLEFR]] commands ||9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrFullDepth || || 9, 4, 25 | | align=“left” |HoleFrFullDepth ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrMidDepth || || 9, 4, 25 | | align=“left” |HoleFrMidDepth ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrPosAxisX || || 9, 4, 25 | | align=“left” |HoleFrPosAxisX ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrPosAxisY || || 9, 4, 25 | | align=“left” |HoleFrPosAxisY ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrPosAxisZ || || 9, 4, 25 | | align=“left” |HoleFrPosAxisZ ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrPosTopX || || 9, 4, 25 | | align=“left” |HoleFrPosTopX ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrPosTopY || || 9, 4, 25 | | align=“left” |HoleFrPosTopY ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrPosTopZ || || 9, 4, 25 | | align=“left” |HoleFrPosTopZ ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrPosX || || 9, 4, 25 | | align=“left” |HoleFrPosX ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrPosY || || 9, 4, 25 | | align=“left” |HoleFrPosY ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrPosZ || || 9, 4, 25 | | align=“left” |HoleFrPosZ ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrRef || || 9, 4, 25 | | align=“left” |HoleFrRef ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrRevCS || || 9, 4, 25 | | align=“left” |HoleFrRevCS ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrThroughType || || 9, 4, 25 | | align=“left” |HoleFrThroughType ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrtipAngle || || 9, 4, 25 | | align=“left” |HoleFrtipAngle ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrTop || || 9, 4, 25 | | align=“left” |HoleFrTop ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrTopClear || || 9, 4, 25 | | align=“left” |HoleFrTopClear ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrTopZ || || 9, 4, 25 | | align=“left” |HoleFrTopZ ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrType || || 9, 4, 25 | | align=“left” |HoleFrType ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |HoleFrWidth || || 9, 4, 25 | | align=“left” |HoleFrWidth ||Number set automatically when using the [[HOLEFR_GET_FEAT]] command || 9, 4, 25 | ||
|- | |- | ||
| align=“left” |LineRef || Number of line created by a line [[:Geometry:Creating_Geometry|geometry]] command||9, 4, 25 | | align=“left” |LineRef || Number of line created by a line [[:Geometry:Creating_Geometry|geometry]] command||9, 4, 25 | ||
Revision as of 22:43, 20 August 2010
| These variables are set by some of the macro commands | Set by | Version Number |
| Button | Number of button pressed on macro dialog. ( OK button = zero ) | 9, 4, 25 |
| CircleRef | Number of circle created by a circle geometry command | 9, 4, 25 |
| ContourRef | Number of contour created by a contour geometry command | 9, 4, 25 |
| CsNumber | Number of CS created by the NEW_CS command | 9, 4, 25 |
| CURRENT_CS_NUM | Number set automatically by the system when a coordinate system is selected or created | 9, 0, 0 |
| CURRENT_WG_NUM | Number set automatically by the system when a workgroup is selected or created | 9, 0, 0 |
| ExcelCellLength | Number set automatically by the system when using the EXCEL_FIND_CELL command | 9, 4, 25 |
| ExcelError | Error code set by all Excel commands | 9, 4, 25 |
| EXCEL_IS_OPEN | Number set automatically by the system dictating whether or not an excel file is open | 9, 0, 0 |
| EXCEL_IS_VISIBLE | Number set automatically by the system dictating whether or not an excel file is visible | 9, 0, 0 |
| FEAT_TYPE_ARC | Number set automatically by the system about a feature type | 9, 0, 0 |
| FEAT_TYPE_CTOOL | Number set automatically by the system about a feature type | 9, 0, 0 |
| FEAT_TYPE_CURVE | Number set automatically by the system about a feature type | 9, 0, 0 |
| FEAT_TYPE_LINE_IJK | Number set automatically by the system about a feature type | 9, 0, 0 |
| FEAT_TYPE_LINE | Number set automatically by the system about a feature type | 9, 0, 0 |
| FEAT_TYPE_MARKER | Number set automatically by the system about a feature type | 9, 0, 0 |
| FEAT_TYPE_POINT | Number set automatically by the system about a feature type | 9, 0, 0 |
| FEAT_TYPE_RAPID | Number set automatically by the system about a feature type | 9, 0, 0 |
| FEAT_TYPE_SPLINE | Number set automatically by the system about a feature type | 9, 0, 0 |
| FileError | Error code set by all file commands | 9, 4, 25 |
| GIBBSCAM_VERSION_1 | Number set automatically by the system dictating the version of gibbscam is running | 9, 4, 24 |
| GIBBSCAM_VERSION_2 | Number set automatically by the system dictating the version of gibbscam is running | 9, 4, 24 |
| GIBBSCAM_VERSION_3 | Number set automatically by the system dictating the version of gibbscam is running | 9, 4, 24 |
| GIBBSCAM_WINDOW_X1 | Number set automatically by the system dictating the first x position of the gibbscam window | 9, 0, 0 |
| GIBBSCAM_WINDOW_X2 | Number set automatically by the system dictating the second x position of the gibbscam window | 9, 0, 0 |
| GIBBSCAM_WINDOW_Y1 | Number set automatically by the system dictating the first y position of the gibbscam window | 9, 0, 0 |
| GIBBSCAM_WINDOW_Y2 | Number set automatically by the system dictating the second y position of the gibbscam window | 9, 0, 0 |
| HoleFrAngle | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrBottom | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrBottomClear | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrBottomZ | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrCS | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrDepth | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrDia | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrDiaTop | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrError | Error code set by all HOLEFR commands | 9, 4, 25 |
| HoleFrFullDepth | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrMidDepth | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrPosAxisX | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrPosAxisY | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrPosAxisZ | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrPosTopX | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrPosTopY | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrPosTopZ | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrPosX | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrPosY | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrPosZ | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrRef | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrRevCS | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrThroughType | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrtipAngle | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrTop | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrTopClear | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrTopZ | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrType | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| HoleFrWidth | Number set automatically when using the HOLEFR_GET_FEAT command | 9, 4, 25 |
| LineRef | Number of line created by a line geometry command | 9, 4, 25 |
| MTOOL_HOLDER | 9, 0, 0 | |
| MTOOL_HOLDER_TYPE | 9, 4, 24 | |
| MTOOL_HOLDER_TYPE_BORE | 9, 4, 24 | |
| MTOOL_HOLDER_TYPE_COLLET | 9, 4, 24 | |
| MTOOL_HOLDER_TYPE_DRILL | 9, 4, 24 | |
| MTOOL_HOLDER_TYPE_MILL | 9, 4, 24 | |
| MTOOL_HOLDER_TYPE_ROT_CLAMP | 9, 4, 24 | |
| MTOOL_HOLDER_TYPE_SHELL | 9, 4, 24 | |
| MTOOL_HOLDER_TYPE_SHRINK_FIT | 9, 4, 24 | |
| MTOOL_HOLDER_TYPE_TAP | 9, 4, 24 | |
| MTOOL_HOLDER_TYPE_TG_COLLET | 9, 4, 24 | |
| PLUGIN_VERSION_1 | 9, 4, 24 | |
| PLUGIN_VERSION_2 | 9, 4, 24 | |
| PLUGIN_VERSION_3 | 9, 4, 24 | |
| PointRef | Number of point created by a point geometry command | 9, 4, 25 |
| ReadVarsNumVars | Number of variables read using READ_NUM_VARS command | 9, 4, 25 |
| SCREEN_HEIGHT | 9, 0, 0 | |
| SCREEN_WIDTH | 9, 0, 0 | |
| SolidRef | Number of solid created by an EXTRUDE_SHAPE command | 9, 4, 25 |
| TOOL_ORIENT_DL | 9, 4, 24 | |
| TOOL_ORIENT_DOWN_LEFT | 9, 4, 24 | |
| TOOL_ORIENT_DOWN_RIGHT | 9, 4, 24 | |
| TOOL_ORIENT_DOWN_RIGHT | 9, 4, 24 | |
| TOOL_ORIENT_DR | 9, 4, 24 | |
| TOOL_ORIENT_LD | 9, 4, 24 | |
| TOOL_ORIENT_LEFT_DOWN | 9, 4, 24 | |
| TOOL_ORIENT_LEFT_UP | 9, 4, 24 | |
| TOOL_ORIENT_LU | 9, 4, 24 | |
| TOOL_ORIENT_RD | 9, 4, 24 | |
| TOOL_ORIENT_RIGHT_DOWN | 9, 4, 24 | |
| TOOL_ORIENT_RIGHT_UP | 9, 4, 24 | |
| TOOL_ORIENT_RU | 9, 4, 24 | |
| TOOL_ORIENT_UL | 9, 4, 24 | |
| TOOL_ORIENT_UP_LEFT | 9, 4, 24 | |
| TOOL_ORIENT_UP_RIGHT | 9, 4, 24 | |
| TOOL_ORIENT_UR | 9, 4, 24 | |
| TOOL_TYPE_35_DEG | 9, 4, 24 | |
| TOOL_TYPE_55_DEG | 9, 4, 24 | |
| TOOL_TYPE_55_PARA | 9, 4, 24 | |
| TOOL_TYPE_80_DEG | 9, 4, 24 | |
| TOOL_TYPE_BACK_BORE | 9, 0, 0 | |
| TOOL_TYPE_BALL_END_MILL | 9, 0, 0 | |
| TOOL_TYPE_BORE | 9, 0, 0 | |
| TOOL_TYPE_CENTER_DRILL | 9, 0, 0 | |
| TOOL_TYPE_COUNTERSINK | 9, 0, 0 | |
| TOOL_TYPE_CUTOFF | 9, 4, 24 | |
| TOOL_TYPE_DRILL | 9, 0, 0 | |
| TOOL_TYPE_FACE_CUTTER | 9, 0, 0 | |
| TOOL_TYPE_FINISH_END_MILL | 9, 0, 0 | |
| TOOL_TYPE_FLY_CUTTER | 9, 0, 0 | |
| TOOL_TYPE_FORM | 9, 4, 24 | |
| TOOL_TYPE_GROOVE | 9, 4, 24 | |
| TOOL_TYPE_KEY_CUTTER | 9, 0, 0 | |
| TOOL_TYPE_PENTAGON | 9, 4, 24 | |
| TOOL_TYPE_REAMER | 9, 0, 0 | |
| TOOL_TYPE_RECTANGLE | 9, 4, 24 | |
| TOOL_TYPE_RIGID_TAP | 9, 0, 0 | |
| TOOL_TYPE_ROUGH_END_MILL | 9, 0, 0 | |
| TOOL_TYPE_ROUND | 9, 4, 24 | |
| TOOL_TYPE_ROUNDOVER | 9, 0, 0 | |
| TOOL_TYPE_SHELL_CUTTER | 9, 0, 0 | |
| TOOL_TYPE_SPOT_DRILL | 9, 0, 0 | |
| TOOL_TYPE_SPOT_FACE | 9, 0, 0 | |
| TOOL_TYPE_SQUARE | 9, 4, 24 | |
| TOOL_TYPE_TAP | 9, 0, 0 | |
| TOOL_TYPE_THREAD_MILL | 9, 0, 0 | |
| TOOL_TYPE_THREAD1 | 9, 4, 24 | |
| TOOL_TYPE_THREAD2 | 9, 4, 24 | |
| TOOL_TYPE_TRIANGLE | 9, 4, 24 | |
| TOOL_TYPE_TRIGON | 9, 4, 24 | |
| TOOL_TYPE_UTIL | 9, 4, 24 | |
| TOOL_TYPE_VPROFILE | 9, 0, 0 | |
| WgNumber | Number of WorkGroup created by the NEW_WG command | 9, 4, 25 |
